DAN A4-SFX: The smallest gaming case in the world

Fantastic news! (Pictures please)

What motherboard are you using? I have the Asus Maximus Impact VIiI. Am am using the C7 cooler now, as I need to cut 5 mm off the top of the (excessively-huge) VRM heatsink to get the Nexus Low 7000 R2 to fit. Now I am concerned about the mounting hardware.

Could four plastic washers be used? I do not have a backplate from a NH-C12P to use. I have the washers from the Cryorig C7. That cooler is loud AF, but it cools well. My guess is the good C7 performance is due to pulling a lot of air from outside the case.

Could you let us Nexus Low 7000 users know what Home Depot calls the right-sized M3 bolts?

These are all the pictures I have for now. I'll try to take more if/when I delid my cpu. https://goo.gl/photos/RkQLiX9XxbLHA3NMA

Home Depot has very little selection for M3 bolts. You'll find them in the pull out drawers on the screw/bolt/nut isle. IMO, you're gonna want to use a backplate, unless you don't mind your motherboard being bent.... which could be very bad. Unless you come up with another way of mounting it. You just need to be creative. It's not too difficult to come up with ideas once you play around with the parts. The specs of my parts are in my sig.

Be careful that when using only a single slot you are running the memory in single-channel mode instead of dual-channel. Consequently, the memory bandwidth will be lower. From my experience this is not very critical when gaming, but this may change in the future.

See also this
I'm not too concerned about memory speeds or single vs dual channel. IMO, all that has minimal effect on everyday PC use (gaming, browsing, MS Office, etc).
 
when I ordered the full copper axp-100, they forgot to include two ty-100 fans so they send another package with lots of freebies! :D

wZCld8A.jpg

Where do you live, and how long was the shipping to you?
 
I'm not too concerned about memory speeds or single vs dual channel. IMO, all that has minimal effect on everyday PC use (gaming, browsing, MS Office, etc).

Cool, just wanted to make sure that you (and anybody reading) was informed.

Your post triggered some renewed interest on my part and I researched it again. My findings confirm your opinion, only in memory intensive cases (e.g. zip, x264) you will find a moderate improvement (~5%) using dual-channel DDR (~20% for quad-channel). I can't seem to find if dual-channel memory actually allows two cpu's to interact with the memory simultaneously, and thus reducing latency. Cores typically have their own MMU's (probably these only operate on the cache), but I don't know how these are connected to the memory controller. Anyway, the benchmarks show that it doesn't really matter.
 
Someone in this thread recommended the Tenba DYOB 13 camera bag for the case.
I want to report that it's a very tight fit with no inches to spare.




That is looking really nice! I am looking for something similar, though maybe cheaper, as I will "just" use it was a sleeve during transportation in my backback.

http://imgur.com/a/Qesf1

i managed to put NF-A4x10 on top of the board as exhaust, havent really tested yet if it helps with the temperature but i can noticeably feel the hot air blowing out, which i think is better than nothing. =)
How about noise? :)



And to those who mount a9x14 on the LP-53:
HOW THE **** AM I SUPPOSED TO DO THIS?! :mad:
I've used maybe 2½ hours fiddling with this, and the best I could do was rubberbands which 1: looks like rubbish 2: interfere with the fans airflow.
 
View attachment 18918

Yes, the bar was removed.

It is not needed for the strength or rigidity for mounting the PSU. With it in place, a 12mm fan fit no problem, but the ridge creates noise.

Not sure how much of a difference, but if you place your hand over it you can feel the heat being pumped out, so I would assume its doing something!

I used the TY100 100mm fan above PSU + lowered PSU. Fits also fine.
 
That's lucky, any chance you don't need that second TY-100? I'm searching for a 100mm pwm fan with no luck other than buying the AXP-100 and using the TY.
You can email Thermalright if you want to buy the TY-100 fan alone.
yep email them, and you can ask for the black and white, black and red or brown and green
Where do you live, and how long was the shipping to you?
6 days, each time, from taiwan to montreal
mcheddadi are those Gears of War pajamas?? :D Amazing.
oh yeah! cole train baby!
 
Someone in this thread recommended the Tenba DYOB 13 camera bag for the case.
I want to report that it's a very tight fit with no inches to spare.




The Lowepro Event Messenger 250 is also a tight AF fit. It is like they made the offical messurments before they added the padding. The A4-SFX does fit the bag, but it takes a little push. It has an exterior pocket that is enough for everything but a keyboard. The internal 13" laptop/tablet pocket can NOT be used, due to the pressure.

https://smile.amazon.com/Lowepro-Event-Messenger-Camera-Shoulder/dp/B0077B403S/

Man, that looks really snug! So would you need a separate bag to transport peripherals or can you still fit a slim wireless keyboard/mouse combo in there somehow?

Most non-gaming wireless keyboards do not have multi-key rollover of any kind. You cannot run, strafe, slide, and reload at the same time.

Now that the "tower" is so small the peripherals are taking up all the space. A mechanical keyboard, over-the-ear headphones, and necessary cables take up as much volume. I hope someone comes out with a folding 27 inch 144 Hz monitor soon.
 
Last edited:
The Lowepro Event Messenger 250 is also a tight AF fit. It is like they made the offical messurments before they added the padding. The A4-SFX does fit the bag, but it takes a little push. It has an exterior pocket that is enough for everything but a keyboard.
Thanks for the tip!

Most non-gaming wireless keyboards do not have multi-key rollover of any kind. You cannot run, strafe, slide, and reload at the same time.
I'm actually looking for something super basic in terms of peripherals on this occasion; planning to use the case as a mobile VR machine. When in use at my desk, I have a full setup right there.
 
Now that the "tower" is so small the peripherals are taking up all the space. A mechanical keyboard, over-the-ear headphones, and necessary cables take up as much volume. I hope someone comes out with a folding 27 inch 144 Hz monitor soon.

This. Honestly, the two places I take my computer regularly, I just bit the bullet - I split the cost of a second 1080p screen with both people, so they get a nice benefit but I get to use the screen when I come over, and I stash a cheapo $5 microsoft keyboard and a mousepad in their closet. That way I only have to bring my mouse and headphones.

Still trying to figure out what to do with headphones, though - there's not a great way to transport mine safely, but I despise earbuds...
 
Any excuse to buy new headphones should be seen as a golden opportunity. Seriously, I have like two or three different headphones stationed at all the various computers and consoles in my home and office......any excuse. :p
 
Has anyone tried mounting a 2½ slot GPU in the DAN A4 case? I just saw the Asus GTX 1080ti Strix on Twitter and lots of people are going to want to know if it's possible to fit it in.
 
Has anyone tried mounting a 2½ slot GPU in the DAN A4 case? I just saw the Asus GTX 1080ti Strix on Twitter and lots of people are going to want to know if it's possible to fit it in.

On a Titan X, with reference cooler. There is 7mm from outside of case, to hitting the GPU's cooler. So 7mm - thickness of the side panel = 7mm - 1.5mm = 5.5mm of space between inside of panel to reference videocard cooler.

I doubt it will fit.
 
Damn.why did asus have to go 2.5 slot for the strix 1090ti. Hoping the EVGA ICX cards will be able to fit now
 
My full copper Axp-100 came in and I went a different route with modifying it. I cut off the blades hanging underneath (using a hacksaw with a 32T blade...) instead of bending the heatpipes. I'm still waiting for my case and parts to come in but I'll let everyone know how the temps are once I get it all together. I've also got a LP53 on the way too, so I'll be interested to compare them both using the A9x14 Fan.

http://imgur.com/gallery/YSe15

n0mgTsol.jpg

MSm3KFMl.jpg

KUBODiUl.jpg
 
Nice! we'll be able to see if bending the heatpipes has a negative effect or not. great stuff man! all that copper must have been long to cut!
 
Nice! we'll be able to see if bending the heatpipes has a negative effect or not. great stuff man! all that copper must have been long to cut!

Haha yeah, it did take a bit of time but I was also trying to do as clean of a job as I could.
 
Case finally arrived and I managed to put almost everything in the case. Still waiting for the GPU though.

33047660250_bcb099ddaf_b.jpg


The challenge was to fit 2 disk drives along with 2 RGB LED strips.

33302432021_559b32439c_b.jpg


Mounted the RGB strips here where they interfered the least with the holes on the bottom of the case

33047659150_b5236d7f9d_b.jpg


The hard drives will sit nicely on top of the strips. With the Corsair SF600 SATA cables, its a bit of a squeeze but it does fit ok

33390466596_2fa275bf1a_b.jpg


Custom cabling helps a lot to keep things tidy. With Asus Strix Z270I, I used lengths of 150mm for the 24pin ATX cable, and 250mm for the 8 pin EPS. The lengths work near perfectly

33302426931_edb6c837e8_b.jpg


With the GPU PCIE cables though, I might have made a mistake. Mine is 200mm and a little too short. It may work with the EVGA dongle that moves the PCIE ports to the back of the GPU but for top mount PCIE i would advise you guys go with 300mm to guarantee compatibility with any GPU and yet not have too much excess cabling

33047654890_9f18c48175_b.jpg


Build more or less finished except for the GPU. Very happy with the result. With my delidded 7700K I was able to get stable 4.8GHz at 1.27V on the test bench but once in the case, although temps never went beyond 80 degrees during benchmarking, it would BSOD. Backing off to 4.7GHz at 1.25V fixed things and max temps seen during benchmarking are 78 degrees. Thanks Dan for making a wonderful case for us to enjoy and hope you guys find the info useful for your builds!

32588071744_539a486dee_b.jpg
 
The Lowepro Event Messenger 250 is also a tight AF fit. It is like they made the offical messurments before they added the padding. The A4-SFX does fit the bag, but it takes a little push. It has an exterior pocket that is enough for everything but a keyboard. The internal 13" laptop/tablet pocket can NOT be used, due to the pressure.

im thinking of cutting off the interior pouch fora tablet, it would then fit without a push. still need to eait for the case to come though.
 
My full copper Axp-100 came in and I went a different route with modifying it. I cut off the blades hanging underneath (using a hacksaw with a 32T blade...) instead of bending the heatpipes. I'm still waiting for my case and parts to come in but I'll let everyone know how the temps are once I get it all together. I've also got a LP53 on the way too, so I'll be interested to compare them both using the A9x14 Fan.

http://imgur.com/gallery/YSe15

n0mgTsol.jpg

MSm3KFMl.jpg

KUBODiUl.jpg

Where was yours shipped too? Trying to find out how long til my gets here in SoCal
 
I'm thinking of cutting off the interior pouch for a tablet, it would then fit without a push. Still need to wait for the case to come though.

Please let us know how A4-SFX fits in the Lowepro Event Messenger 250 after the tablet pouch is removed. It may give the needed few millimeters so that I do not have to push or shake to get the computer to fit each time.

I do not want to cut out my tablet pouch as I had hoped to use it for a 11" 1080p 60Hz GeChic portable monitor if there was space. I still want to use the Event Messenger 250 for accessories and cables, even if I decide on something like the Tenba byob 13 for the case.
 
Now that the "tower" is so small the peripherals are taking up all the space. A mechanical keyboard, over-the-ear headphones, and necessary cables take up as much volume. I hope someone comes out with a folding 27 inch 144 Hz monitor soon.
I've actually been downsizing my peripherals, or at least getting portable versions of peripherals. My results:
Keyboard: Ajazz AK33 mechanical keyboard with Grifiti Chiton sleeve
Headphones: Beyerdynamics DT-1350-80
Speakers (if you dislike headphones like me): Edifier MP300 Plus 2.1 speakers (or Edifier Aurora which is the same thing but come without the protective pouch), you can power this off the PSU with a molex to 5.5mmx2.5mm barrel adapter since it runs off 12V. Incidentally this is where the "hole" at the GPU bracket comes in handy.
Monitors: Portable HDMI monitors from Aliexpress or Taobao(sells for cheaper if you can use the website), most 15.6" power off USB, a 17.3" version powers off 12V (again you can use a molex to 5.5mmx2.5mm barrel adapter to run it off the PSU), most of them are 8-bit IPS monitors unlike Gechic's 6-bit monitors. Throw them in a separate laptop bag to prevent damage. We won't be seeing gaming portable monitors though.
Storage: Stick 2x4TB or 2x5TB 2.5" 15mm Seagate drives in the A4. If you need external drives, use 2.5", don't use enclosures as they add unnecessary weight, get SATA->USB adapters instead and silicone sleeves for the 2.5" drives.
Wires: Can't do anything about this, but some HDMI cables are thinner than others.
 
Last edited:
How did you get down the Psu ??
Like this
Yeah, I guessed it was for vertical stability. If it doesn't have any other purpose could it instead go down, along the side of the PSU?

Reason I'm asking is, I looked at the free space (at least 3cm since a SFX-L fits there) there is when using a SFX PSU and thought how to take advantage of that. One of the biggest drawbacks for this case is that there is no active exhaust which makes the case and components pretty hot - seen by the temp difference when not using the I/O panel.
I figured that there is enough room for a 92mm top fan if you lower the PSU with spacers/extending bracket, that attaches to the stock bracket, to make room for the powercable and airflow. It would also pull air from the GPU side. Below is a quick sketch of it:
View attachment 17081

Something for A4-SFX v2?

More great pictures by loafidelity.
or this
The PSU bracket is a separate removable piece, right? So I wouldn't even have to do it this way:

I could just lower the whole bracket by drilling new screw holes 3cm lower on the front side and putting spacers to the mb side screws. Or would there be something blocking moving it down 3cm? Is there someone who could test out the temp difference? even just adding a fan outside the case on the top and temporarily lowering the PSU for better airflow?
Dan, could these extra holes be added to v2 and the top of the inner frame made 92mm fan friendly? I wager a lot of people would be interested in adding an active exhaust to the case.

Unfortunately, just measuring based on this pic http://i.imgur.com/9qw1acX.jpg a 92mm fan wouldn't be completely flat against the top panel since the bottom right corner would be against the inner frame.
 
Back
Top