Arctic Cooling Accelero Xtreme 5970 now available!

dun dun dun. I smell fried 5970 on the way lmao. Really though i wouldnt attach that thing to my card if it would fry it. But hey its your choice

Wouldn't you give it a try if your HD5970 ratled like a b*tch?

This rattle noise is very annoying, I can't concentrate on any game with that damn noise, that's the only reason im going for accelero xtreme :/
 
Wouldn't you give it a try if your HD5970 ratled like a b*tch?

This rattle noise is very annoying, I can't concentrate on any game with that damn noise, that's the only reason im going for accelero xtreme :/

Headphones, or watercooling. Or both. :)
 
Wouldn't you give it a try if your HD5970 ratled like a b*tch?

This rattle noise is very annoying, I can't concentrate on any game with that damn noise, that's the only reason im going for accelero xtreme :/

Oh ya i,m brave i'll roll the dice i hate that annoying POS ATI fan. So I was extremely careful installing it. Did not not over tighten and viola both DVI ports work like a charm, displayport works, card runs cool and quiet. All is sweet.

Wait wait what happened everything just went dark, I was lovin it for about 5 minutes. card was drooping under the wait of the cooler then no display on any ports DVI or display port. No beep on boot up. 700 dollar brick.

I rolled the dice after reading this whole post, just new I would be the lucky one. Just like last trip to Vegas, going home broke. Well are you feeling lucky, I was. Now I'm just feeling kind of stupid. I mean everyone here did warn me, I have no one to blame but myself.
 
Oh ya i,m brave i'll roll the dice i hate that annoying POS ATI fan. So I was extremely careful installing it. Did not not over tighten and viola both DVI ports work like a charm, displayport works, card runs cool and quiet. All is sweet.

Wait wait what happened everything just went dark, I was lovin it for about 5 minutes. card was drooping under the wait of the cooler then no display on any ports DVI or display port. No beep on boot up. 700 dollar brick.

I rolled the dice after reading this whole post, just new I would be the lucky one. Just like last trip to Vegas, going home broke. Well are you feeling lucky, I was. Now I'm just feeling kind of stupid. I mean everyone here did warn me, I have no one to blame but myself.

Good lord! I'm speechless. AC should really do the right thing and take these damn things off the market. You were very careful to follow AC's amended instructions and still bricked your card! :rolleyes:
 
Headphones, or watercooling. Or both. :)

Watercooling is not an option for me :/ Out of my budget xD

I got the G35 headphones, which are really good to remove the noise from the outside, but I can still hear the ratle lol.

Oh ya i,m brave i'll roll the dice i hate that annoying POS ATI fan. So I was extremely careful installing it. Did not not over tighten and viola both DVI ports work like a charm, displayport works, card runs cool and quiet. All is sweet.

Wait wait what happened everything just went dark, I was lovin it for about 5 minutes. card was drooping under the wait of the cooler then no display on any ports DVI or display port. No beep on boot up. 700 dollar brick.

I rolled the dice after reading this whole post, just new I would be the lucky one. Just like last trip to Vegas, going home broke. Well are you feeling lucky, I was. Now I'm just feeling kind of stupid. I mean everyone here did warn me, I have no one to blame but myself.

F*ck... I'm not willing to have a $700 brick xD I am really considering to refuse the package on Monday.
 
Hey guys!

The cooler arrived this morning.

I installed it 20 mins ago, and both DVI ports work just fine, installation was pretty easy to be honest.

FAN on auto (From 50% to 60% usually, and it's very silent):

Ambient Temp in my room: 27ºC
Iddle: 33ºC
Full (Furmark + Xtreme Burning mode): 62ºC

This cooler is damn great.

Also I want to ask you something, what is the VDDC Phase temps? With furmark they're almost 90ºC according to GPU-z, but im not sure what that is, I mean with gaming bad company 2 they don't go even close to that, so not sure what the VDDC Phase X temps are.
 
Use afterburner and turn the fan up so it does to 95% at around 45 degrees. Its really quiet like this and the most I see in Furmark is 53 on the cores and 69 on the voltage regs on my Toxic.

Regards
Fred
 
Use afterburner and turn the fan up so it does to 95% at around 45 degrees. Its really quiet like this and the most I see in Furmark is 53 on the cores and 69 on the voltage regs on my Toxic.

Regards
Fred

I realised that while playing BC2 with fan on Auto it only reaaches 47ºC, so cool :D

And it's damn silent :)

I'm so glad I bought this cooler, ZAS in your face to everyone who said I would break it lol :p (It's not an insult, i am just happy that I am winning that bet :p NO! I didnot break it :D NICEEEEEEEEEEE)
 
Hey guys!

The cooler arrived this morning.

I installed it 20 mins ago, and both DVI ports work just fine, installation was pretty easy to be honest.

FAN on auto (From 50% to 60% usually, and it's very silent):

Ambient Temp in my room: 27ºC
Iddle: 33ºC
Full (Furmark + Xtreme Burning mode): 62ºC

This cooler is damn great.

Also I want to ask you something, what is the VDDC Phase temps? With furmark they're almost 90ºC according to GPU-z, but im not sure what that is, I mean with gaming bad company 2 they don't go even close to that, so not sure what the VDDC Phase X temps are.

borat_great_success-450x337.jpg
 
FrozenCPU is selling the cooler, i submitted a review linking to this thread

Well.

I didn't kill my card, maybe AC is right and you're not supposed to tight the X plates 100%, I tight them like 50% or so (A few turns only, but safe so it is still).

I mean, I feel very sorry for those of you who got a $700 brick, but I must say, this cooler (At least for me) is damn great.

Another thing, did Arctic Cooling contact any of you about ur HD5970 see if they'll replace it? :/
 
Another thing, did Arctic Cooling contact any of you about ur HD5970 see if they'll replace it? :/

Arctic Cooling has not responded to anyone about their damaged cards. Everyone did charge backs on their credit cards. I am considering opening a small claims suit against the company for the cost of my card. I know they won't pay but I just want to see if they respond.

I'm glad you didn't damage your card, but let's not forget that Arctic Cooling is a piece of shit company that deserves no ones business.
 
Arctic Cooling has not responded to anyone about their damaged cards. Everyone did charge backs on their credit cards. I am considering opening a small claims suit against the company for the cost of my card. I know they won't pay but I just want to see if they respond.

I'm glad you didn't damage your card, but let's not forget that Arctic Cooling is a piece of shit company that deserves no ones business.

I do agree with you.

But, why do the cards break? I still don't understand. I followed the instructions and my card is fine, maybe im just very lucky?

Here are some more pictures:







I am not totally sure, but I think the card is bended a little bit, but Ican't really tell right now, didn't take the time to look at it closely.
 
My card does not look bent. I tightened my screws barely snug and dead DVI port. You are lucky.
 
You concluded..."I fully recommend this cooler to anyone with an HD5970 (Although you must be very patient while installing it, and take your time)."

I would have added that you must be patient, LUCKY, and slightly out of your mind when installing this cooler.

Well, I've seen many people with this cooler @ Overclock.net

Without tighten the screws too much, all cards are alive, I think it's a user-friendly problem, and not Arctic Cooling's problem.

In Overclock.net so far 4 users this week have installed the Accelero Xtreme 5970 and none killed their DVI ports, therefor I fully recommend this cooler as long as you don't over-tighten the screws.

Or ask me if you don't understand - I'm french - because google translate is a piece o sh*t ! :mad:

:p
 
Well, I've seen many people with this cooler @ Overclock.net

Without tighten the screws too much, all cards are alive, I think it's a user-friendly problem, and not Arctic Cooling's problem.

In Overclock.net so far 4 users this week have installed the Accelero Xtreme 5970 and none killed their DVI ports, therefor I fully recommend this cooler as long as you don't over-tighten the screws.

:p

Actually, it is ACs problem, the original instructions that these people used, said to tighten the screws to 100%, which killed their dvi ports, only later did they state to use 50% or w/e. read back a few pages, someone posted the original, after AC posted an update.

I'm tempted to buy this cooler, but after all of these people got screwed, with no help from AC, I don't feel as if I should give this company any of my $.
 
Actually, it is ACs problem, the original instructions that these people used, said to tighten the screws to 100%, which killed their dvi ports, only later did they state to use 50% or w/e. read back a few pages, someone posted the original, after AC posted an update.

I'm tempted to buy this cooler, but after all of these people got screwed, with no help from AC, I don't feel as if I should give this company any of my $.

I felt same way as you. But seeing as 100% of the people at Overclock.net who followed new instructions (Don't over-tighten any screws) didn't get their DVI ports killed, I decided to buy it, and here I am, with a DAMN GREAT cooler, and DAMN SILENT!!

I totally recommend you to get it.
 
Personally speaking I would be wary of a product where the difference between flawless operation and it bricking your $700 component was a subjective tightening of screws. I really feel they should develop a better mounting system or advise users to forgo the X-clamps if the screws are that risky.
 
I felt same way as you. But seeing as 100% of the people at Overclock.net who followed new instructions (Don't over-tighten any screws) didn't get their DVI ports killed, I decided to buy it, and here I am, with a DAMN GREAT cooler, and DAMN SILENT!!

I totally recommend you to get it.

it's the principle, unless they help the people who they screwed over with the first set of instructions, I refuse to give them my $! I could have easily been one of those people, and out a $700 card, it's not right.

I totally recommend a complete boycott of all AC products, until they provide some sort of help for the people that lost their cards, honestly, I'm sort of shocked that you even stand behind it.
 
Last edited:
hi guys, i'd like to post some large pics (1024x768) of my install and write some information that may help people with their installs in the future. Would it be inappropriate to post it right here? Thanks.
 
hi guys, i'd like to post some large pics (1024x768) of my install and write some information that may help people with their installs in the future. Would it be inappropriate to post it right here? Thanks.

Please post it here.
 
Hi guys, just wanted to share some pics on my experience and leave you with a bit of info. I successfully installed the heat sink but not without help from reading on this forum the problems that everyone else had. I felt very bad for the people that were mislead by the instructions and ruined their cards at their own expense. So I registered just to share my pictures and experience for the people that plan on installing this in the future. I'll write the info after the last picture. Thanks.

01.jpg

02.jpg

03.jpg

04.jpg

05.jpg

06.jpg

07.jpg

08.jpg

09.jpg

10.jpg
 
11.jpg

13.jpg

12.jpg




Ambient: 25c

CPU Cores: 42c 37c 41c 35c



GPU Cores: 900MHz @ 1.174v

Memory Clock: 1100MHz


Fans at 35% during idle
Fans at 45% when temps go over 60c

*Fan speeds were controlled through MSi Afterburner 1.5.1

GPU1: Min 27c Max 63c
GPU2: Min 32c Max 64c


* Max was produced through 20 minutes of Modern Warfare 2
with all settings on max. This game runs the GPU's hotter
than anything I know, including furmark.


Installation experience:


-Picture 5 circles the 2 screws that the instructions did not tell me to remove, as you cannot remove the heat sink without removing those 2 screws as well.


- I reposted pictures of the instructions because 100% screw in is way too much for the retention clips.

During the retention clip install I would turn (tighten) the first screw literally 2-3 times around immediately after catching thread with the screw. Then finally
I would do the same for the rest. Even at 2-3 turns on the screw I could feel how firmly I needed to hold the clip down so that the screw wouldn't pop out
during fastening. This was already a hint for me to not over tighten. When all the screws were on from 2-3 turns tightening I did NOT continue to tighten
the screws more, I left it as is.

And just as another way to give you an idea on how little i screwed it in: The screw heads were not anywhere close to being flush with the back plate. You could
feel them bump outwards a bit from the backplate/bracket.



On 3rd to last picture where it shows the card installed in my computer case: The heat sink is not THAT heavy that it will sag your video card down.

I was lucky that the 6pin/8pin cables that i used were very stiff so the way i have them standing actually supports the video card in the PCIe slot as displayed in the picture.



*** hate to write a disclaimer but I'm posting these pictures and experiences for only sharing purposes. You are solely responsible for your own installation.
If anything fails because you followed my experience, I am not held responsible. Thanks again.
 
Last edited:
I know what you mean.


I eye'd the percentage. The screws are very short and they each have a small spring attached to them.

As I was saying, once each screw caught thread, I would not turn more than 2-3x around. I did that for all 4 sides and left it as is. It felt VERY tight already.
 
In an earlier part of my life, I've worked on jet engines, diesel and gasoline engines. I've worked on hydraulic, pneumatic and for the last 20 years computers. I've never been instructed by any reputable company to tighten a device using an eyeball or 50% feel tight measurement. If their engineering was done correctly I would expect their documentation to reflect the same degree of professionalism. Now for those who sucessfully tighten their screws 50 percent, I wish you the best. If it's only 50 percent tight, then there's a 50 percent chance of them coming loose. Good Luck! My bet is with a manufacturer to designs things to hold together 100 percent!

Correctly engineered, the damn thing should have shims, spacers or whatever, and then tighten the screws 100 percent. Is that so damn hard?
 
Last edited:
Back
Top