Search results

Been looking for one of these for a while now and have been eyeing the Rosewill RX81-MP-SC. What is the consensus best external enclosure here at [H]?

Anyone heard of this one yet? LED backlit, IPS, supposedly a 30-bit panel with a range of more than a billion colors. Specs: http://h10010.www1.hp.com/wwpc/us/en/sm/WF06a/382087-382087-64283-72270-444767-3648397.html

i've got an oem hdd that i'd like to install but since it didn't come with any screws do you guys know of a good place to get them? the Frys i went to didn't have them and i also tried RadioShack for the hell of it (no luck). thanks

Just wondering how often you guys clean your cases and how? What are some good ways to prevent dust from collecting inside?

alright..ive never seen this happen before but today i was running stress prime and it always seems core 2 just "hangs" in that it is still running and didnt throw any errors but it stays on the same test while core 1 keeps going. if i run stress prime only on core 2 it seems to advance but...

Hi all I just got a new Radeon x1900xtx, the plain ATI version. I tried overclocking with Overdrive in the CCC but it would not let me change any of the speeds for core or memory. I tried ATI Tray Tools but it reported that overclocking was disabled..anyone know how to get around this...

I'm using a 500 W PS but it doesn't have a 6-pin connector for my new Radeon x1900xtx. is the only solution to buy a PS with the 6-pin connector?

I've been thinking of switching to a DFI board from my current vanilla Asus A8N-SLi to get a better OC. I have an Opteron 165 and 2GB OCZ PC4000 EB. I've narrowed it down to the two boards in the topic but based on what I read at DFI Street, DFI boards are quite picky about the power supply and...

have any of you asus a8n-sli owners gotten your ram to run at ddr500 or above on 1t? I've got OCZ PC4000 EB 2GB and can't get my system stable. I've got this memory paired with an Opteron 165 which I would like to keep at 2.8 Ghz with a 333/400 divider. my calculations show the ram speed on this...

i've just reseated my scythe ninja after cleaning it and the cpu heatspreader with 99% isopropyl alcohol and coffee filters. i've applied AS5 per the instructions on the Arctic Silver website but my idle temperature is 41c and load around 54c. I notice my mobo temp is 39c too..is that too hot...

I recently upgraded to the OCZ Platinum EB (PC4000) 2GB kit. I have an Asus A8n-Sli paired with an Opteron 165 @ 2.8 GHz on stock volts. I've got the ram voltage at 2.7 volts and am using the rated timings of 3-3-2-8 @ 1T. I am running a 333/400 ratio and have the multiplier at 9x so my ram...

got mine at 2.8 ghz on stock volts, dual priming gets me 53c according to Asus probe. Asus probe has been notorious for its high readings but Speedfan says the same thing. I read that anything above 50c would slowly kill the cpu..any truth to this? whats the max load temp you guys think is safe...

Ive been doing research into a good 2gig kit (to be OC'd) to go with my Asus A8n-Sli but there doesn't seem to be any good answers. The G.Skill 2GB HZ kit seemed like a good choice but I've read numerous posts in other forums that 250 mhz is very hard to reach; those that do seem to only be able...

hi i heard that SATA ports 3 and 4 are locked on the a8n-sli so i switched my sata hdd to port 4. is there any way to confirm if this port is locked in the BIOS? Looking through the BIOS options and menus I couldnt seem to find any indication that port 4 was locked. anyone with this mobo...

put in stock opteron 165 yesterday with the scythe ninja+120mm Yate Loon and AS5. asus probe reports 34c idle, and 46c load. is this typical of the ninja's performance? i was hoping for lower temps, especially on stock volts. i think i did a pretty good job with the mount and the AS5...

alright, ive heard this tool isnt too accurate. some say it overstates temps by as much as 10c.. i just installed an opteron 165 (still at stock speed and voltage) with a scythe ninja+yate loon fan. asus pc probe says the cpu temp is 34c at idle. this sound right to you guys? do you guys use...

hi all, right now ive got 2x512 MB mushkin value ram and would like to upgrade to a 2GB kit. G.Skill seems to be a popular choice here, so i'd like to know which 2GB G.Skill kit is the best for OC'ing based on your experiences. based on some preliminary research it looks like the 2GB HZ kit...

Just got a scythe ninja but i broke the stock backplate when i tightened the screws too hard. i tried to use the ninja backplate but the cross shape won't align perfectly flat with the back of my Asus A8n-Sli board. There are three inductors right under the CPU socket and under each of them on...