DAN A4-SFX: The smallest gaming case in the world

Cool! Do you have any pictures of how you modified the mounting bracket?

I mounted it without taking photos, but you can see the area I cut out of the narrow ILM bracket under the copper heat pipes on the right side of the image above. Here's a picture of where to make the cuts (drawn in red)

pTl8Rnx.jpg
 
You want to provide a link? A google, ebay, and amazon search turns up nothing for me.

It is because it's under a different brand.

Did anybody that have the Nexus Low 7000 R2 noticed something at the box of the cooler?

I did noticed this on the box of my cooler...
ur57vk7l2f55glczg.jpg


I googled CoolJag and found this...
cc201304021652415902.png


The CoolJag Falcon 2. It's the same as the Nexus Low 7000 (not the R2)

It is available at the following sites;

Schneider-Consulting-Elektronik - Listed as compatible with LGA 1366/1156/775

Orbit Micro - Listed as compatible with LGA 775/1366

Antares Pro - Listed as compatible with LGA 1366/1356/1156/1155/1150/775

Frozen CPU - Listed as compatible with LGA 1366 only


The downside is that the cooler is a bit on the expensive side, around $40+. The mounting compatibility is also sketchy, differs from every seller but the CoolJag site indicates that it is compatible with Intel sockets 1366/1356/1156/1155/ 775. And how stable the four heatpipes at the CPU block are once the skivetek heatsink is removed/unscrewed.
 
Last edited:
It is because it's under a different brand.

Did anybody that have the Nexus Low 7000 R2 noticed something at the box of the cooler?

I did noticed this on the box of my cooler...

I googled CoolJag and found this...
cc201304021652415902.png


The CoolJag Falcon 2. It's the same as the Nexus Low 7000 (not the R2)

It is available at the following sites;

Schneider-Consulting-Elektronik - Listed as compatible with LGA 1366/1156/775

Orbit Micro - Listed as compatible with LGA 775/1366

Antares Pro - Listed as compatible with LGA 1366/1356/1156/1155/1150/775

Frozen CPU - Listed as compatible with LGA 1366 only


The downside is that the cooler is a bit on the expensive side, around $40+.

very nice!! you can even use liquid metal thermal paste on it because is copper on the bottom http://www.frozencpu.com/products/image/8624/cpu-cjg-31_3.jpg
 
So the c7+noctua fan works well enough, thanks for the information and tests.

Will the lp-53 + noctua fan perform better than the c7+noctua fan?

What about noise with side panel? Won't the LP53 + noctua fan be quieter since it's overall height will be lower than C7 + noctua fan?
 
The LP53 will be quieter, every cooler smaller then the C7 is quieter with the Noctua fan. And no, the C7 isnt a silent wonder now with the Noctua fan, he is still noisy
 
The LP53 will be quieter, every cooler smaller then the C7 is quieter with the Noctua fan. And no, the C7 isnt a silent wonder now with the Noctua fan, he is still noisy

Someone earlier said: "But if you want to be quiet, lp53(40mm height) is worth it."

Yeah, that's significantly lower height for the same performance with the noctua fan. Just making sure my effort to implement the LP53 isn't lost since I already own the C7.
 
It is because it's under a different brand.

I googled CoolJag and found this...
cc201304021652415902.png


The CoolJag Falcon 2. It's the same as the Nexus Low 7000 (not the R2)

It is available at the following sites;

Schneider-Consulting-Elektronik - Listed as compatible with LGA 1366/1156/775

Orbit Micro - Listed as compatible with LGA 775/1366

Antares Pro - Listed as compatible with LGA 1366/1356/1156/1155/1150/775

Frozen CPU - Listed as compatible with LGA 1366 only


The downside is that the cooler is a bit on the expensive side, around $40+. The mounting compatibility is also sketchy, differs from every seller but the CoolJag site indicates that it is compatible with Intel sockets 1366/1356/1156/1155/ 775. And how stable the four heatpipes at the CPU block are once the skivetek heatsink is removed/unscrewed.

Thanks! I took a risk and ordered one of these from Frozen CPU.
 
Thanks! I took a risk and ordered one of these from Frozen CPU.

Really nice to see same cooler in another brand.

Wounder if it will be possible to get AM4 mounting kit to that cooler, have buyed it direct if i got that confirmed or is it hard to do a own mounting kit ??
 
Really nice to see same cooler in another brand.

Wounder if it will be possible to get AM4 mounting kit to that cooler, have buyed it direct if i got that confirmed or is it hard to do a own mounting kit ??

Thermalright's Narrow ILM adapter works with this cooler and mounts to either Intel Narrow 2011 socket or AMD's AM3 socket. Do we know how AM4 compares to AM3? If the coolers are compatible this will work with that as well.
 
Thermalright's Narrow ILM adapter works with this cooler and mounts to either Intel Narrow 2011 socket or AMD's AM3 socket. Do we know how AM4 compares to AM3? If the coolers are compatible this will work with that as well.

Alot of cooler brands have confirmed they will give out free mounting kits to AM4 so i think its all new to AM3.

Noctua, Cryorig, Phanteks, Coolermaster and more in Sweden not checked other countries policies.
 
All will be collected on Monday or Tuesday.

How long can we expect for shipping from Germany to US? I'd assume around two weeks with all the water in the way. I'm planning a trip around the arrival of my case. Real important stuff...

I doubt you're using consumer shipping, but I was only able to get DHL quotes for 2-3 day shipping from Germany to US.
 
I emailed noctua (support@noctua.at) about the those metal retention clips from the NH-L9x65 bundle, and they said they would send me a pair for free with proof of purchase of the NF-A9x14 fan. Really nice of them!
Nice! I will do the same when I get my lp53+a9x14 then :) That is really a nice service.
 
The CoolJag Falcon 2. It's the same as the Nexus Low 7000 (not the R2)

The mounting compatibility is also sketchy, differs from every seller but the CoolJag site indicates that it is compatible with Intel sockets 1366/1356/1156/1155/ 775. And how stable the four heatpipes at the CPU block are once the skivetek heatsink is removed/unscrewed.

The second problem I encountered with the Falcon II was the mounting solution for LGA 1156 motherboards -- or lack thereof. The Falcon II comes readily adjustable for LGA 775 and 1366 mobos, but the third set of holes that were supposed to be for 1156 are too small for the provided mounting screws. It's like whoever made the Falcon II used the wrong drill bit, but made a hole anyway in the perfect spot. Using a dremel tool, I carved out the metal in between the LGA 775 and 1366 holes to create a slide-like hole (I would recommend using a drill-bit to bore out the 1156 hole instead of a metal disk like I used to cut everything out). After this mod, I simply made sure all the mounting studs were evenly spaced between where the LGA 775 and 1366 holes used to be. The included thermal paste is, surprisingly, top-notch stuff: Shin-Etsu X23-7762. It is [H]ard to spread, in my experience, but has achieved great results in various reviews.

This fan was reviewed here back in 2010, and I quoted the mounting compatibility fix with the 115x
 
Hi guys, i was trying to find out the clearance on the Nexus/Cooljag cooler, so we can figure out the height of RAM that would be OK to fit underneath the heat sink.

I found this iamdarkyoshi's review on linustechtips:

https://linustechtips.com/main/topi...xus-low-7000-cpu-cooler-20-plus-sh-on-amazon/

He seems to be using Crucial Ballistix Sport LT DDR4 RAM, which has a height of 44mm, as you can see it fits fine underneath the heat sink in the picture he has posted.

I am very happy with that as my Trident Zs are 44mm in height also, so if i use the a9x14 fan underneath the heat sink everything should fit just fine, the trident Zs are pretty tall for RAM, so most peoples RAM should be just fine if you intend to install a 92mm fan.

I hope this clears things up for some people, please don't feel like you HAVE to buy new ultra low profile RAM unless you really really want that 120mm fan underneath.
 
I went to the coolJag website and subtracted the height of the fan from the cooler, it comes out to around 50mm tall. Since the case only allows up to 48mm cooler height isn't this an issue? Not sure if the original poster fit his into the case. If not I'd be willing to test with a 120mm Scythe Slip Stream 2000rpm fan. Might need to remove the heat spreaders on my gskill ram but willing to try.

Can someone confirm if the 50mm height would work?

Thanks! I took a risk and ordered one of these from Frozen CPU.
 
I went to the coolJag website and subtracted the height of the fan from the cooler, it comes out to around 50mm tall. Since the case only allows up to 48mm cooler height isn't this an issue? Not sure if the original poster fit his into the case. If not I'd be willing to test with a 120mm Scythe Slip Stream 2000rpm fan. Might need to remove the heat spreaders on my gskill ram but willing to try.

Can someone confirm if the 50mm height would work?
If the case is perfectly built, you have 50mm of space.

50mm is max but for example the thermalake apx-100 muscle at 52 mm is too much
 
I went to the coolJag website and subtracted the height of the fan from the cooler, it comes out to around 50mm tall. Since the case only allows up to 48mm cooler height isn't this an issue? Not sure if the original poster fit his into the case. If not I'd be willing to test with a 120mm Scythe Slip Stream 2000rpm fan. Might need to remove the heat spreaders on my gskill ram but willing to try.

Can someone confirm if the 50mm height would work?

Shaav answered this a few pages back


Because that was the official number (including some manufacturing tolerance etc.). If the case is perfectly built, you have 50mm of space.

And Dan posted a drawing of the height of the cooler after the mod

1cb4e12d4a.jpg

It will just about fit, and it shouldn't make much noise as the fan is way below the side of the case underneath the heat sink
 
Increasing the stability of the shroud



Thats not even the problem. There are few problems:
  • CPU are different, doesnt matter if the run @ same vcore
  • I doubt that the people really know their ambient temperature
  • Everyone is using different thermalpaste
  • The test parameters are probably different and not documanted (sidepanel off, which RPM are the running at etc)
  • If someone only tested one cooler, then his temps are pretty useless since u cant vaildate the data

Thats the reason why i dont trusts most of the results, only those where i know that they make sure the have the same test parametes with their coolers.

Exactly, that is what I meant with the second part. Most people don't really now how to isolate one parameter and meassure it properly (because they don't have to know it).
 
It is because it's under a different brand.

Did anybody that have the Nexus Low 7000 R2 noticed something at the box of the cooler?

I did noticed this on the box of my cooler...
ur57vk7l2f55glczg.jpg


I googled CoolJag and found this...
cc201304021652415902.png


The CoolJag Falcon 2. It's the same as the Nexus Low 7000 (not the R2)

It is available at the following sites;

Schneider-Consulting-Elektronik - Listed as compatible with LGA 1366/1156/775

Orbit Micro - Listed as compatible with LGA 775/1366

Antares Pro - Listed as compatible with LGA 1366/1356/1156/1155/1150/775

Frozen CPU - Listed as compatible with LGA 1366 only


The downside is that the cooler is a bit on the expensive side, around $40+. The mounting compatibility is also sketchy, differs from every seller but the CoolJag site indicates that it is compatible with Intel sockets 1366/1356/1156/1155/ 775. And how stable the four heatpipes at the CPU block are once the skivetek heatsink is removed/unscrewed.

I just ordered from Frozen CPU. I love that site. So... to confirm I'm going to mount the noctua 14mm fan on this using the rubber pegs and I don't have to worry too much about ram height. (I have G.skill Tridentz)
 
I just ordered from Frozen CPU. I love that site. So... to confirm I'm going to mount the noctua 14mm fan on this using the rubber pegs and I don't have to worry too much about ram height. (I have G.skill Tridentz)

Looks like the base of the cooljag is copper with a mirror finish, and not direct heatpipe like the R2. Someone with both will have to test with the same system and conditions to determine which is better. I'll be reporting on the Jag, but my 7700k delid is quite the edge case. Hopefully someone acquires both.

Jag

upload_2017-2-16_16-50-6.png


Versus R2

upload_2017-2-16_16-50-29.png
 
Be aware that the cooljag is Build differenty. The fins doesnt seem to be glude anymore
 
My first DIY cable mode.

Corsair SF450 and Asus Z270i Strix

I made the CPU cable 24 cm. It is on the long side but 20 cm will be tight.

yveziktteiwnsgp.jpg

What ram is that?

I also have a z270 for my build, how do the RGB on the Mainboard look when the sidecover is on--do they shine through the grating?
 
The Nexus Low-7000 R2 that I ordered from Japan came today. I been playing around with it, taking measurements, taking it apart, ect.

One thing I noticed is the original modifier of it bend his heat pipes some. You can see them bow out here:

6tauCAe.jpg



Here are some other known measurements:

5ZGPfh0.jpg



Here is an unbend version with the stock 20mm fan inserted below, w/o the top aluminum block that normally has the fins, and is 4.5mm thick (that block is also used to sandwich the socket brackets):

sjx1Fax.jpg



Here is what an unbend version measures from bottom of cpu block surface to top of heatsink fins (~45.5mm, you gain a few mm of clearance by removing/flipping the stock fan brackets):

qRQv4ry.jpg



Anyway, I'm thinking of making a thinner top block to sandwich in the cpu socket brackets to gain more clearance. Or possibly just using nuts and bolts to hold the brackets. Then if possible bending the heatpipe like the original modifier there might be enough room to fit a 120x25mm scythe gentle typhoon, assuming you use VLP ram, and it clears other motherboard stuff.

If you look at the 2nd picture above, you'll see there is an unknown value of space between his 15mm fan and the top of the 4.5mm block top, which looks to be greater than 5mm. So if you can take 15mm (fan), 4.5mm (block top), and the unknown space that appears to be more than 5mm, you might have more than enough space to fit a 25mm thick fan in there.

I have 4 other Nexus Low-7000 R2's coming (used by the the manufacture, Nexus - I asked to buy any used/engineering samples they had laying around, and all they had was 4). So my plan is to experiment with at least 1 of those, and unload the others. But my goal is to get my 120x25mm scythe gentle typhoon PWM fan in there :)
 
OK I just got my strix z270i today. so I test fit my ram and nexus cooler. the cooler fits with the heatpipes almost touching the strix top metal heat sink and the ram fits under it with maybe 3 or 4mm of space left. ( i got normal sized ram without a tall heatsink on it.) the left strix heat sink needs to be grinded or unscrewed from the mother board if I want to put a 120mm fan bellow the nexus cooler. also the wifi module will need to be modified or grinded or the fan will have to be offset 2~3 mm to make room for it or with a dremel one could remove a chunk of plastic from the fan where it meets the wifi module. I'm waiting to see if I can get my VLP ram. otherwise I've already got the noctua NF-A9x14 if I can't get it to fit at all
 
OK I just got my strix z270i today. so I test fit my ram and nexus cooler. the cooler fits with the heatpipes almost touching the strix top metal heat sink and the ram fits under it with maybe 3 or 4mm of space left. ( i got normal sized ram without a tall heatsink on it.) the left strix heat sink needs to be grinded or unscrewed from the mother board if I want to put a 120mm fan bellow the nexus cooler. also the wifi module will need to be modified or grinded or the fan will have to be offset 2~3 mm to make room for it or with a dremel one could remove a chunk of plastic from the fan where it meets the wifi module. I'm waiting to see if I can get my VLP ram. otherwise I've already got the noctua NF-A9x14 if I can't get it to fit at all

Thanks. Sounds like this will just drop in on the strix 270i with normal RAM and a 92x14mm fan. Very reassuring.
 
FWIW Amazon has Z270i listed directly (rather than Marketplace via 3rd party seller) again, though no stock until next week.
 

Attachments

  • z270i.PNG
    z270i.PNG
    41.5 KB · Views: 109
(regarding cooljag/nexus LOW7000 (non R2) Based on its appearance, the fins above the CPU are part of the upper alum block, and should be a tight compression fitting with the heatpipes.

Appears as though those with the Nexus LOW7000 (not R2) and the cooljag will need to mechanically cut off the fins from the top plate as they are part of the top half of the cpu block.

Looks as though the upper block with the fins can be removed though, and thus removed temporarily for grinding off the fins. I also hope the pipes are soldered to the bottom copper plate.




So my plan is to experiment with at least 1 of those, and unload the others. But my goal is to get my 120x25mm scythe gentle typhoon PWM fan in there :)

Saw the GT in your photo :)

I am totally in for one of the heatsinks when this eventuates.
 
Last edited:
Back
Top