DAN A4-SFX: The smallest gaming case in the world

Also spec sheet for AR05, same thing. If you are lazy to tweak (like me), buy a 65W non-K and be happy forever :)

ar05.PNG
 
Higher voltage + higher frequency = too much heart for little coolers. You can scale back the K processor to behave like non-K. You're all saying the same thing. Let's stop going around in circles.

As for the PC not booting Wezelkrozum dondan mine wouldn't boot with my graphics card because the metal piece (that sticks out at the back of the case that holds the card) was too tall, preventing the riser PCI slot from making full contact with the card. I had to unscrew the riser at which point it all worked.

I highly recommend people build outside of the case first, so it's easier to debug.
 
I guess I'll have to take off my case side off for the time being, until a good cooling solution has been found, it sucks :(

The problem with a 140mm or 120mm on the c7 is, that the biggest part of the air went not through the heatsink, because air will use the easiest way.

Use the A9x14 fan with the included 12v to 9v adapter (low noise adapter).
 
The problem with a 140mm or 120mm on the c7 is, that the biggest part of the air went not through the heatsink, because air will use the easiest way.

Use the A9x14 fan with the included 12v to 9v adapter (low noise adapter).

Dan as anyone posted the same problem as i did? About the side panel blocking ths C7 fan?
 
Can someone try to mount the fans on the side panel to see what it does to C7 noise and temp when there is no gap between the fan and side panel? Preferably both the C7 fan and the Noctua one.

@gna582 - You really managed "i5-7600K 4500 Mhz 1,12 V 67 °C 23 °C 1800 92 x 14 NF-A9x14 PWM Noctua NH-L9i" with no mods? no delid? no direct die mount? stock TIM?
 
Can someone try to mount the fans on the side panel to see what it does to C7 noise and temp when there is no gap between the fan and side panel? Preferably both the C7 fan and the Noctua one.

@gna582 - You really managed "i5-7600K 4500 Mhz 1,12 V 67 °C 23 °C 1800 92 x 14 NF-A9x14 PWM Noctua NH-L9i" with no mods? no delid? no direct die mount? stock TIM?
Asking people to post their OC/temp results online in a public spreadsheet is like asking people for their weight. Some make it look better than it actually is because of personal reasons and some just have bad scales which do not give you proper values.
it is the same here, some may use the most 'optimistic' numbers they saw and some might just not really know how they can properly monitor everything to insure the results are correct (not deactivating C states while testing thermals, not monitoring ambient the whole time, running it for a too small time etc.), measuring things is hard, there is a reason that it is a full scientific discipline (metrology).
 
Did anyone have a go at the DeepCool HTPC200 CPU coolers? looks like it will fit right in, though might have the same issues as the C7 in terms of turbulens due to sitting to c lose to the sidepanel?

The heatsink looks a lot like the silverstone AR05
 
Edges like those are often added for strength purposes.
Yeah, I guessed it was for vertical stability. If it doesn't have any other purpose could it instead go down, along the side of the PSU?

Reason I'm asking is, I looked at the free space (at least 3cm since a SFX-L fits there) there is when using a SFX PSU and thought how to take advantage of that. One of the biggest drawbacks for this case is that there is no active exhaust which makes the case and components pretty hot - seen by the temp difference when not using the I/O panel.
I figured that there is enough room for a 92mm top fan if you lower the PSU with spacers/extending bracket, that attaches to the stock bracket, to make room for the powercable and airflow. It would also pull air from the GPU side. Below is a quick sketch of it:
DAN-A4-top-fan.png


Something for A4-SFX v2?

More great pictures by loafidelity.
 
Yeah when i put the side panel you can ear the fan hitting it and then it stops =s
Did you modify anything that adds height to the mobo or the heatsink? I have a C7 in my Dan A4 and have no trouble closing the sidepanel. Also a lot of guys on German forums installed C7s and I did not read of any problem..

There was some mention here and there of using the C7 heatsink with the Noctua L9i fan...does anyone know if this gets rid of the noise while giving the c7 superior cooling performance?

If anyone has done this, could you also let us know how you secured the noctua fan to the C7 heatsink?

I've got both the C7 and L9i and am thinking of cannibalising the fan from the noctua to use with the C7 if it improves temps/noise

Edit: i just compared the noctua to the c7 fan. Theres hardly any difference between them. 2-3mm at the most. I have my doubts whether this difference would be enough to solve the noise issue

Ok securing the noctua fan to the c7 heatsink is possible with cable ties. Using the noctua fan, you save a grand freaking total of 2mm compared to the c7 fan. I am unsure if this will help things at all

Just registered to leave my two cents regarding this..
I switched the C7 stock fan for the Noctua A9x14 fan yesterday. After booting the pc I detached the sidepanel again to see if the fan was even spinning because I did not hear it..
Running Prime tests I only noticed a silent whisper. Nothing I would consider bothering and nowhere annoying like C7 stock. Temperatures rose about 3° but I don't have any problem with that.
Having seen/heard this I immediately canceled my orders of the NH-L9i and SST-AR05 as I am happy with both temps and noise of C7 heatsink + A9x14 fan.
Added test results for my Xeon E3-1230 v3 to Shaav's google doc.

About mounting the fan to the heatsink I found some examples on German forums:
zip ties:
upload_2017-2-16_12-54-42.jpeg

wire:
upload_2017-2-16_12-54-50.jpeg

nails :eek::
upload_2017-2-16_12-54-30.jpeg

s-hooks + tension spring:
upload_2017-2-16_12-55-32.jpeg
 
Did you modify anything that adds height to the mobo or the heatsink? I have a C7 in my Dan A4 and have no trouble closing the sidepanel. Also a lot of guys on German forums installed C7s and I did not read of any problem..



Just registered to leave my two cents regarding this..
I switched the C7 stock fan for the Noctua A9x14 fan yesterday. After booting the pc I detached the sidepanel again to see if the fan was even spinning because I did not hear it..
Running Prime tests I only noticed a silent whisper. Nothing I would consider bothering and nowhere annoying like C7 stock. Temperatures rose about 3° but I don't have any problem with that.
Having seen/heard this I immediately canceled my orders of the NH-L9i and SST-AR05 as I am happy with both temps and noise of C7 heatsink + A9x14 fan.
Added test results for my Xeon E3-1230 v3 to Shaav's google doc.

About mounting the fan to the heatsink I found some examples on German forums:
zip ties:
View attachment 17084
wire:
View attachment 17085
nails :eek::
View attachment 17083
s-hooks + tension spring:
View attachment 17086
THIS! makes me so happy :)
 
What is this raised edge for?

Increasing the stability of the shroud

Asking people to post their OC/temp results online in a public spreadsheet is like asking people for their weight. Some make it look better than it actually is because of personal reasons and some just have bad scales which do not give you proper values.
it is the same here, some may use the most 'optimistic' numbers they saw and some might just not really know how they can properly monitor everything to insure the results are correct (not deactivating C states while testing thermals, not monitoring ambient the whole time, running it for a too small time etc.), measuring things is hard, there is a reason that it is a full scientific discipline (metrology).

Thats not even the problem. There are few problems:
  • CPU are different, doesnt matter if the run @ same vcore
  • I doubt that the people really know their ambient temperature
  • Everyone is using different thermalpaste
  • The test parameters are probably different and not documanted (sidepanel off, which RPM are the running at etc)
  • If someone only tested one cooler, then his temps are pretty useless since u cant vaildate the data

Thats the reason why i dont trusts most of the results, only those where i know that they make sure the have the same test parametes with their coolers.
 
Last edited:
Did you modify anything that adds height to the mobo or the heatsink? I have a C7 in my Dan A4 and have no trouble closing the sidepanel. Also a lot of guys on German forums installed C7s and I did not read of any problem..

I didn't modify anything about the cooler, i noticed that mine as a little elevation if i push the fan down i can see the black plastic beneath the fan moving down, don't know if it's normal or not.

Seems like i will buy an A9x14 fan and apply it on the C7 heatsink like you mention, thank you for your opinion :)
 
Did you modify anything that adds height to the mobo or the heatsink? I have a C7 in my Dan A4 and have no trouble closing the sidepanel. Also a lot of guys on German forums installed C7s and I did not read of any problem..



Just registered to leave my two cents regarding this..
I switched the C7 stock fan for the Noctua A9x14 fan yesterday. After booting the pc I detached the sidepanel again to see if the fan was even spinning because I did not hear it..
Running Prime tests I only noticed a silent whisper. Nothing I would consider bothering and nowhere annoying like C7 stock. Temperatures rose about 3° but I don't have any problem with that.
Having seen/heard this I immediately canceled my orders of the NH-L9i and SST-AR05 as I am happy with both temps and noise of C7 heatsink + A9x14 fan.
Added test results for my Xeon E3-1230 v3 to Shaav's google doc.

About mounting the fan to the heatsink I found some examples on German forums:
zip ties:
View attachment 17084
wire:
View attachment 17085
nails :eek::
View attachment 17083
s-hooks + tension spring:
View attachment 17086

Thank you for the very informative post!

As I mentioned before, the difference in height between the C7 fan and the A9x14 is just 2mm, i just measured it just now. I am quite surprised that this 2mm can make such a big difference. I'm now wondering if it would be possible to just grind away 2-3mm from the fan of the C7 to make it work optimally in the Dan A4.
 
I think it is not only the 2mm difference in height but also the quality of the bearing and the whole fan itself.
My C7 stock fan was annoying even at low speed with no sidepanel at all and idling pc.
 
So the c7+noctua fan works well enough, thanks for the information and tests.

Will the lp-53 + noctua fan perform better than the c7+noctua fan?
 
So the c7+noctua fan works well enough, thanks for the information and tests.

At least for my setup with a non OC CPU. Don't know if there are reserves for OC'ing big time.

Will the lp-53 + noctua fan perform better than the c7+noctua fan?

According to other tests probably not very noticeable and not worth to me comparing it as I'm happy now.

Only disadvantage: I can now hear coil whine under load as there is no fan going bonkers anymore :D
 
just ordered a few more parts , I ordered the l9i , I already have the c7 so at the very least I can swap fans, hopefully you guys don't come up with something else and then I need to buy another cooler, and the next cooler I buy will be a dans if he decides to make one
 
For people with a Asus motherboard. Try downloading the 'Asus Ai suite 3' and run the 'Fan Expert 2' program. In idle my C7 went from 29 Degrees (delid) and 1300 RPM to 30 degrees and 700 RPM. It's now quiet at idle and under load it's audible but not as before.
 
For people with a Asus motherboard. Try downloading the 'Asus Ai suite 3' and run the 'Fan Expert 2' program. In idle my C7 went from 29 Degrees (delid) and 1300 RPM to 30 degrees and 700 RPM. It's now quiet at idle and under load it's audible but not as before.
I also did this and it changed the behaviour of the fan but its just as loud as it was before especially under load (Gaming). However, it doesn't skyrocket in the same way.
 
Did you modify anything that adds height to the mobo or the heatsink? I have a C7 in my Dan A4 and have no trouble closing the sidepanel. Also a lot of guys on German forums installed C7s and I did not read of any problem..



Just registered to leave my two cents regarding this..
I switched the C7 stock fan for the Noctua A9x14 fan yesterday. After booting the pc I detached the sidepanel again to see if the fan was even spinning because I did not hear it..
Running Prime tests I only noticed a silent whisper. Nothing I would consider bothering and nowhere annoying like C7 stock. Temperatures rose about 3° but I don't have any problem with that.
Having seen/heard this I immediately canceled my orders of the NH-L9i and SST-AR05 as I am happy with both temps and noise of C7 heatsink + A9x14 fan.
Added test results for my Xeon E3-1230 v3 to Shaav's google doc.

About mounting the fan to the heatsink I found some examples on German forums:
zip ties:
View attachment 17084
wire:
View attachment 17085
nails :eek::
View attachment 17083
s-hooks + tension spring:
View attachment 17086

Thank you for sharing this with us!

Trying to visualize, how would you strap a zip-tie on the C7 heatsink? still baffled.
 
I know... I can't really return my XT140 just because it performs worse, I've already opened and used it. :p

I guess I'll have to take off my case side off for the time being, until a good cooling solution has been found, it sucks :(
dude thank you thank you thank you!!! I wish more ppl saw this issue as we do!! if I could reach through the internet I would shake you hand! I fucking hate seeing ppl do that. "blah blah bitch bitch, kaby not OC as fast as I EXPECTED, ill exchange it try another. nope still not as fast as I EXPECT. returned. fuck you kaby!" or this one almost made me loose my shit "so ive been mining on these gpus for almost three months and I changed my mind I don't want them. returned." no! fuck off! you don't get to return shit like that, it abusing the system and fucks over the store and potentially anyone that, usually unknowing, ends up with your returned product. un-opened and un-used returns only for me.
 
I may have a few Nexus Low-7000's available to part with, for those located in the US. I'll know more when they arrive in the middle of next week.
 
For those planning X99 builds in the A4, I wanted to follow up on dondan's comment that the Nexus LOW-7000 provides the best cooling performance and how to attach it to the Asrock X99 ITX board. I've used the dynatron t318 for over a year and have found the cooling performance to be subpar, Dan recommended the Nexus LOW-7000 as a possible option and had the best cooling of anything tested. Here's what you need to attach it to the Narrow ILM socket on the Asrock X99 board:

1. Nexus LOW-7000: remove the bottom aluminum fins that attach directly to the heat pipes; also remove the included fan from the heat sink
2. Thermalright Narrow ILM kit: you'll need to use a saw and cut the narrow cross bars on one end of the adapter, this is so the heat pipes of the Nexus LOW-7000 cooler can be routed upwards properly.
3. Thermalright TY-100 100mm fan or Noctua's 92mm thin fan: you'll slide this beneath upper aluminum fins in place of the lower aluminum fins and attach to the upper fins with zip ties
4. The crossbar attachment for the heatsink, the 4 LGA 2011 adapter posts, and the four corresponding screws from any Thermalright cooler mounting kit (such as the axp-100), these attach to the Thermalright narrow ILM kit (instructions are on the box)

See below for the finished product on the Asrock X99E-ITX/ac. I'm confident that this solution will perform much better than the dynatron t318!

Uunw8MC.jpg

FypKSZU.jpg


Those are the coolers that require low-profile RAM right?

They don't require low profile RAM! If you used low profile RAM I believe you could fit a slim 120mm fan under this heat sink as well.
 
Last edited:
Highly interested. How much money, do you estimate?

I'm not sure, first I need them to be delivered, so I can make sure they are in okay condition. I don't think they are brand new, which shouldn't make a difference as long as they have all the screws, brackets, ect.
 
For those planning X99 builds in the A4, I wanted to follow up on dondan's comment that the Nexus LOW-7000 provides the best cooling performance and how to attach it to the Asrock X99 ITX board. I've used the dynatron t318 for over a year and have found the cooling performance to be subpar, Dan recommended the Nexus LOW-7000 as a possible option and had the best cooling of anything tested. Here's what you need to attach it to the Narrow ILM socket on the Asrock X99 board:

1. Nexus LOW-7000: remove the bottom aluminum fins that attach directly to the heat pipes; also remove the included fan from the heat sink
2. Thermalright Narrow ILM kit: you'll need to use a saw and cut the narrow cross bars on one end of the adapter, this is so the heat pipes of the Nexus LOW-7000 cooler can be routed upwards properly.
3. Thermalright TY-100 100mm fan or Noctua's 92mm thin fan: you'll slide this beneath upper aluminum fins in place of the lower aluminum fins and attach to the upper fins with zip ties
4. The crossbar attachment for the heatsink, the 4 LGA 2011 adapter posts, and the four corresponding screws from any Thermalright cooler mounting kit (such as the axp-100), these attach to the Thermalright narrow ILM kit (instructions are on the box)

See below for the finished product on the Asrock X99E-ITX/ac. I'm confident that this solution will perform much better than the dynatron t318!

They don't require low profile RAM! If you used low profile RAM I believe you could fit a slim 120mm fan under this heat sink as well.

Cool! Do you have any pictures of how you modified the mounting bracket?
 
Back
Top