Some questions about my new PC.

Final_Omen

n00b
Joined
Jul 1, 2007
Messages
19
Let's start with my specs... (This is my first post too!)

Intel C2D E6300 @ 7x450
Asus P5B-Plus
Corsair XMS2 5400C4 2x1024MB @ 900 5-5-5-15
eVGA 8800GTS 320MB SC @ 600/1800
Creative X-Fi XtremeMusic (discontinued)

OCZ GameXStream 600watt
*Lian-Li PC-A12 + *2x Scythe S-Flex SFF21F
*Thermalright SI-128 + *Silverstone FM121

3x WD 2500KS 250GB
*2x WD 5000AAKS 500GB
*LG 18X SATA DVD Burner

*Anything with an asterisk I haven't bought yet.

My main concern is cooling. With the Lian-Li PC-A12 only has 2 120mm fans, will the 2 Scythe S-Flex fans be enough to keep everything cool... enough? Also, I am in the market for a down-facing HSF for my CPU to help cool my memory and northbridge. As of right now (Centurion 5 with side open, stock cooling + AS5, passive memory, passive northbridge) my CPU temp hits 82 in TAT. My northbridge I'm assuming is somewhere around 50-55, and my memory just slightly below that. My videocard also hits 77-78 full load @ 90% fan speed. So I know the new cooling setup will help alot, but is there anything else that I might want to consider, maybe different fans? I'm not to sure I could go after another case, after I saw the PC-A12, I was blown away. What an elegant, quality case. Also, will the down-facing HSF help cool my northbridge and memory somewhat? I'm definitely not expecting a 10 degree drop just from the extra air movement from the cpu fan. Any other comments or suggestions on cooling will be greatly appreciated!

Now in terms of hardware, is there anything I should of done differently? Even though I already bought the components, would you guys recommend something else in exchange what I currently have? Personally I'm very happy with the speed and overall price this system cost me, I'm very satisfied, especially with the overclocking results.

Speaking of overclocking, what should my voltages be at? I was thinking my temps might be too high due to too much voltage. Now I haven't gone into the bios and tweaked around until I found the right voltage for my overclock, and I wont until I get my new cooling, but just to help me out with that, can I get an idea of what my voltages should be at.

Finally, my soundcard. While the X-Fi is a decent soundcard, I think I'm going to see how the Auzentech X-Fi 7.1 Prelude does. Mainly because of the extra outputs ON THE CARD!!! However, it looks like it will be using Creative drivers, so thats a bit of a turn-off. Main reason I want to replace my current soundcard (even if the one I want uses the same APU) is because I hear crackling and pops once every couple hours, almost as if extra energy builds up and discharges at a certain point. Although I could be way off...

Anyways, thanks for any comments/suggestions/answers you guys can give me! :)
 
check out a freezer7 pro or scythe ninja for your cpu, they're pretty popular these days. everything else looks good.

voltages...which ones? psu rails should be withing 5% of spec, and I really' can't say about your cpu voltage. different chips need different amounts of voltage to run, and I don't know offhand what speeds people are getting with different voltages on that chip...

your cpu temp, is that in celsius? I'm assuming its not, because there's no way it would be stable at 82 celsius. if it says 82c, then its a bad probe/software. rule of thumb, if you can't hold your finger on a hsf for more than a few seconds, its too hot.

crackling and popping: check what else is plugged into the circuit. I had a fridge plugged into the same surge protector one time, and everytime the compressor engaged, my speakers popped.
 
X-Fis just crackle, a lot of them. It comes down to poor quality control, from everything I've read -- the Creative forums are a giant pulsing sack of rage over this and any number of other issues on any given day of the week, and Creative doesn't even pretend to care.

I'd look at Yate Loons rather than the Scythe fans. They average around $4 as opposed to $15, and seem to be very good. I've been happy with mine.

I've been very happy with my P180B, but that Lian Li is a good option as well.

Samsung Spinpoint drives are reportedly fast and quiet... and I've personally never had good luck with WD drives (I have literally 6 or 7 dead to prove it) but it all comes down to personal preference there.

Keep voltages as low as you can possibly go, stable, for longevity and heat reasons. Never go above 1.5 vcore or so, as people around 1.55+ to 1.60 have killed chips.

TAT is not a good stress test -- it gives numbers above anything you will /ever/ see in real world usage.. Use Orthos or OCCT.
 
Thanks for your input guys. But I have a new problem... I will start a new thread if I can't get the problem figured out tomorrow when I bring my PC into my work to diagnose. Anyways, after messing around with some overclocking, my cpu no longer is dual core (wtf?). Yes, only one core now shows up. When my machine POSTs it shows a 2cpu count, but is it possible to fry just one core? I can no longer overclock to any extent either. Also, my machine will only boot after I clear the CMOS, if I restart my machine now, for example, it will not boot. I almost hope my cpu is fried, gives me a reason to get a E6420, but I having a feeling this is one dead motherboard.



Back to the topic at hand though. Does a down-facing heatsink help cool other components, such as northbridge, memory, or am I better off getting a HSF tower? I rather not have to replace my northbridge cooling.
 
Well you really have messed it up. In task manager click view -> CPU history -> One graph per CPU.
 
Back to the topic at hand though. Does a down-facing heatsink help cool other components, such as northbridge, memory, or am I better off getting a HSF tower? I rather not have to replace my northbridge cooling.

I'm not sure what you're talking about here. Every standard heatsink i've seen will have a fan pulling air 'down' through the heatsink. In that respect, no, it actually heats up your other components. Still, its better than the alternative, which is to pull in warm air from your other components and pull that through the fins (pulling 'up' through the heatsink) which would result in higher cpu temps.

When you say tower, do you mean something a heatpipe design like the ninja or tuniq tower?
 
Don't use TAT to find your C2D temps. TAT wasn't designed for C2D nor has it been updated for C2D CPUs. Use either CoreTemp or Speedfan to find out your true CPU temps.
 
Back
Top