Resurrect your 360 Controller Battery

Domingo

Fully [H]
Joined
Jul 30, 2004
Messages
24,293
After trying to play Dishonored with a dying 360 Plug-&-Play battery pack I ran upon this neat little trick. Yes, I know you can just use normal rechargeable batteries - but this works just as well, especially if you have one laying around that won't keep a charge.

http://www.youtube.com/watch?v=QXaIlyjvvSE

In my case, the controller would light up green like it was fully charged, but died in 5-10 seconds after unplugging it. This little trick made it run like new.
Plus, it works regardless if you're using it with a 360 or a PC. Mine was a launch day controller/charge kit.
 
yep, smart chip are not that smart, even most phones have some special feature to reset the battery life counter. however the batteries once they get old they lose the charge faster though.
 
wish i would have seen this vid 4 years ago when i had a play n charge pack that only worked when plugged in.
 
I brought 2 back from the dead last night. I used one of them for at least 2 hours and it was still doing fine afterward.
 
Nice! Just found an old battery pack last month in my tv stand and it was pooched like this. Would say changed but die in 10 seconds.
 
Sweet! I found 2 of my old packs that wouldn't charge, tried this trick, and it worked! Well, one pack charged for about 3hrs and seems to be working 100% but my other one just wont charge at all. Not bad considering both are well over 2 years old.
 
Nice, wish something like that worked with those Wii battery packs. Have a rechargeable energizer that didn't even last a year before failing. Never bothered with returning as figured if I needed to ship back it would cost as much as the whole unit did :(
 
Nice, wish something like that worked with those Wii battery packs. Have a rechargeable energizer that didn't even last a year before failing. Never bothered with returning as figured if I needed to ship back it would cost as much as the whole unit did :(

Yeah, same here. I have a MadCatz Wii charging stand with 2 battery packs that are pretty much worthless. Every now and then one will randomly work for about 15 minutes, but they usually die in seconds.
 
Will have to try this when I get home. Both batteries won't keep the controller on for more than a couple minutes after charging.
 
That's so interesting. Can anyone explain the technicals behind it?
The intent behind this is that the batteries have an expected life cycle (charge/discharge), so the pack counts that cycle then shows failure when it's reached. They do this for a couple reasons, 1 so that you replace the battery before they fail, and 2 so that you replace the battery and have to buy more pricey Microsoft licensed hardware. The reality is that they may show failure even though the batteries may be able to continue operating for a while.

Print manufacturers do this for ink cartridges too, they show empty after x amount of print jobs, even if some ink may be left.

The procedure being performed is simply clearing the logic counters on the device, essentially setting the count back to zero, fooling the unit to believing it's brand new.
 
Last edited:
Is it dangerous? (battery failure)

I would say yes, using the paper clip method to discharge the battery is quite dangerous. You never EVER want to directly short across a battery.

A better method would be to use a common 2.3 volt flashlight bulb or a resistor of some sort.


With that being said lots of people have used the paper clip method and I haven't heard of anything exploding yet.
 
well just did this, my old pack was so old didnt even heat up the wire once. Skipped ahead tot he reseting it part and it ha sbeen charging off my 360 for 3 hours now and still going. Would only "charge" for like 30 minutes before and show full lol.
 
I tried it too. 1 of 3 dead batteries seems to be restored. Another went from charging for 1 sec to charging for about 1 minute, but still dead.
 
Tried on both mine. Neither got the wire hot, but 1 seems to be charging now. The other still goes green after a few seconds on the charger so it may just be dead for good.

Edit: I spoke too soon, the other battery only charged for about 5 minutes so I think both of mine are beyond saving.
 
Last edited:
So inside the battery pack they are just AA Sanyo's. I'm going to see if they dead ones are really dead by taking them apart and trying to charge them on a standard charger.

Edit: Too them apart, one battery won't charge at all, another charged for about 5 mins before being full. The other two are still going. I'll try to test and refresh them on my lacrosse charger and see how much life they have left.
 
Last edited:
So inside the battery pack they are just AA Sanyo's. I'm going to see if they dead ones are really dead by taking them apart and trying to charge them on a standard charger.

Snip*

What? Just AA batteries? My whole life has been a lie! :(
 
The intent behind this is that the batteries have an expected life cycle (charge/discharge), so the pack counts that cycle then shows failure when it's reached. They do this for a couple reasons, 1 so that you replace the battery before they fail, and 2 so that you replace the battery and have to buy more pricey Microsoft licensed hardware. The reality is that they may show failure even though the batteries may be able to continue operating for a while.

Print manufacturers do this for ink cartridges too, they show empty after x amount of print jobs, even if some ink may be left.

The procedure being performed is simply clearing the logic counters on the device, essentially setting the count back to zero, fooling the unit to believing it's brand new.
Thanks!
 
What? Just AA batteries? My whole life has been a lie! :(

Take apart a 9v. It's usually just six AAA's.

Quite common to use whatever cells are available and then repackage them at a premium. Hence why you usually get the standard "AA" adapter with a wireless controller.
 
Take apart a 9v. It's usually just six AAA's.

Quite common to use whatever cells are available and then repackage them at a premium. Hence why you usually get the standard "AA" adapter with a wireless controller.

Good luck trying to cram six AAA batteries into a 9 volt cell...

Perhaps you meant AAAA...
 
So far the batteries removed from the packs seem to be pretty good.
1800, 1900, 1700 out of 2100 mah.

M3wHN.jpg
 
The intent behind this is that the batteries have an expected life cycle (charge/discharge), so the pack counts that cycle then shows failure when it's reached. They do this for a couple reasons, 1 so that you replace the battery before they fail, and 2 so that you replace the battery and have to buy more pricey Microsoft licensed hardware. The reality is that they may show failure even though the batteries may be able to continue operating for a while.

Print manufacturers do this for ink cartridges too, they show empty after x amount of print jobs, even if some ink may be left.

The procedure being performed is simply clearing the logic counters on the device, essentially setting the count back to zero, fooling the unit to believing it's brand new.

you forgot one of the most important reasons.

Once the batteries have reached the end of their service life, they can explode when charged and that is not a good thing.
 
you forgot one of the most important reasons.

Once the batteries have reached the end of their service life, they can explode when charged and that is not a good thing.

OK, I can't stand it, I'll bite... please provide reliable linkage that states that NiMH cells can explode when they've reached the 'end of their service life'.
 
OK, I can't stand it, I'll bite... please provide reliable linkage that states that NiMH cells can explode when they've reached the 'end of their service life'.

lithium cells will explode not nimh, there is no need to use a smart chip with nimh cells....
 
This is why it's better to use AAs with a good charger IMO. Easier to swap 'em out, recharge, etc.

When my AAs start getting cranky I run them through the recharge-refresh cycle on my LaCrosse charger - take a day or so to discharge/recharge/discharge batteries until it stops seeing improvement in the capacity - gets them refreshed and working again.

A good charger plus a good handful of Eneloops / Rayovac Hybrids does the trick. And as a bonus, they also work great in the kids' toys, remote controls, Wiimotes, etc.
 
Awesome, glad to see it worked. Thanks for spreading the word, I'm glad to see people not getting duped into buying new battery packs when the existing should work fine. :D


After trying to play Dishonored with a dying 360 Plug-&-Play battery pack I ran upon this neat little trick. Yes, I know you can just use normal rechargeable batteries - but this works just as well, especially if you have one laying around that won't keep a charge.

http://www.youtube.com/watch?v=QXaIlyjvvSE

In my case, the controller would light up green like it was fully charged, but died in 5-10 seconds after unplugging it. This little trick made it run like new.
Plus, it works regardless if you're using it with a 360 or a PC. Mine was a launch day controller/charge kit.
 
Back
Top