Brand New Opty 165 Stepping CCBBE 0610DPMW New "BB" Memory Controller

Spazilton said:
Only reason I got the K8N-SLI for my wife is that it worked out to right at $90 with the rebates. She is going to have a single 7800GT for now, maybe upgrade to SLI one of these days. I already owned the Memory(Mushkin PC4400 TCCD), and the 7800GT. So for around $350 I upgraded her from a P4 3.0 1GB 9800 Pro to an Opty 146 @2.8 7800GT,($90 for the Mobo, $143 for the Processor and $99 for the Antec Neo HE 550. and other odds and ends) and the best part is her 8300 still has some fairly decent resale value on ebay, so I should probally come very close to breaking even.
Click to expand...
abit did make a decent overclocker at one point but since dfi hit the market, it seems nobody gets close, my buddy bought that ax-8 for a steal so I don't blame him 43. shipped, and he doesn't really plan on overclocking much so it should do him fine.
 
Spazilton said:
Its going into my SLI-DR Expert this afternoon. Since the 170 in my sig is going bye-bye.

Only crappy part is that I'm out of AS5, and only have Cermauique left. I don't think there is anywhere local I can pick up AS5.
Click to expand...

ceramique is just as good as AS5 and easier to clean up/re-apply, AS5 is really not impressive to me when you factor in cost and cleanup + it gets hard and needs to be re-applied more often, ceramique is superior IMO and theres no risk factor either
 
Spazilton said:
I have to give her 146 almost 1.5 to get stable at 2.8 and its a CACJE 0607 which should do much better.
Click to expand...

Interesting, my 146 CACJE 0607 is stable at 2.8 with stock voltage on my KN8 Ultra, air cooled with a XP90. Maybe Abit messed up with o/c stability with the SLI's.
 
I'm done testing this chip, it's good for 300x9 and 1.344 volts on a 24/7 basis, anything more pushes the limits of my mobo/cooling setup and more voltage doesn't seem to help. I tried to scale the 3 GHz barrier, but no luck even at 1.472. DId do fine at 2.95 though.

my.php


didn't bother priming at 2.95 because knowing whether its completely stable or not at that speed is irrelevant to ]
 
freddy418 said:
I'm done testing this chip, it's good for 300x9 and 1.344 volts on a 24/7 basis, anything more pushes the limits of my mobo/cooling setup and more voltage doesn't seem to help. I tried to scale the 3 GHz barrier, but no luck even at 1.472. DId do fine at 2.95 though.

my.php


didn't bother priming at 2.95 because knowing whether its completely stable or not at that speed is irrelevant to ]
Click to expand...

Yea that looks like you are hitting a wall on your motherboard.
 
Yup last couple of days has been a crap shoot on steppings from Monarch.

Some got the 0610s

Others have gotten 0551s or even one person got a 0543.

PS the 0610s are shaping up to be beasts! :)
 
Spazilton said:
Yup last couple of days has been a crap shoot on steppings from Monarch.

Some got the 0610s

Others have gotten 0551s or even one person got a 0543.

PS the 0610s are shaping up to be beasts! :)
Click to expand...

What's yours ending up at? Mine seems to do 3GHz at 1.5v but 3042 is a no go even at 1.6v. We'll see if the one coming on monday is a CCBBE 0610
 
repoman0 said:
What's yours ending up at? Mine seems to do 3GHz at 1.5v but 3042 is a no go even at 1.6v. We'll see if the one coming on monday is a CCBBE 0610
Click to expand...

I just got done with 4 tests For US History that were due today. So Im going to grab some food and break down the Install the chip on my expert. I should have results in 3 hours or so. 3.0 at <1.5 is going to be what Im shooting for.
 
So what is a good non-SLI board for these that will OC like mad? I've currently got a K8N Neo4 SLI and it has never oc'd worth a dump for me.
 
since I do not have much money, is there a way that I can buy from a store and know that I will get a good cpu from 2006?
 
brycejones said:
So what is a good non-SLI board for these that will OC like mad? I've currently got a K8N Neo4 SLI and it has never oc'd worth a dump for me.
Click to expand...
Dfi ultra-d is a strong oc'er and should give you better numbers then the msi.
 
gotfrag? said:
since I do not have much money, is there a way that I can buy from a store and know that I will get a good cpu from 2006?
Click to expand...
If you have a local fry's, micro center or pc club they will let you hand pick the chip you want. They generally charge more than the e-tailers and they charge tax but you know what stepping you are getting.
 
Leaving this running for a while, I dont think I have a good mount on my TTBT, might have to redo it.
 
Yeah, I redid my mount too, instead of constant 38C at stock volts it's now 36-38C with the occasional jump to 41-42 :confused: But I think the temp sensor on my board is wack, it stays at ~38C up to 1.45v, same as my 0550vpmw would do.

Dual priming overnight at [email protected] to be completely sure of stability.. keep my room nice and warm while I sleep.
 
Well 2800 @ Stock did 30 min or so seemed to be going fine.

I found out I was having a lot of my problems because I kept the chipset at 1.5. A bump to 1.6 has greatly helped stability. I was getting wierd stuff like on a lockup the boot screen would be corrupted until a cold reboot.


2825 Fails after a coulpe of minutes. I think you are going to beat me with the watercooling. Going to prime another 1hr and then start adding some voltage.
 
Ok, so I went and picked mine up.(Opty 165) I got the 0551 version. =_= Not exactly what I was hopping for, but I heard that this thing can hit 2.5Ghz easy on stock voltage right? That's all I'm shooting for since I placed the order really.

EDIT: I have the Zalman 7000B Cu if that helps in OC this sucker at all.
 
Honestly,
Probally not. Ive heard the 0551s on the low end not doing over 2.25. Average seems to be around 2.6 with decent (1.5+) Voltage.
 
Well shit.

Prime just failed at 2800 @ stock. after 1hr and 5 min.

Screw this its voltage time...
 
Booted into windows at 3.0Ghz 1.45v going to see how stable it is.

Yey Primed for a whopping 2 seconds on Core 1 lol.

Guess its time for a tad more.

Decided to back it off to 2950 and See how that goes.

Right now Priming 2950 @ 1.45
 
These ships are just insane. I rmember the 0530's being the best then the 0550 and now these 06 chips. It just keeps getting better.
 
This chip doesn't scale at all well with voltage on air. I can't get anything over 2.92 stable with anything up to 1.525v. It starts acting wierd over 1.45. Everything fails on core 1.

I dont think its a CC1BE 0550 killer. I think its above the 0530, but below the 0550.

I know the temp sensor on the Expert is hosed, Im reading 43c with it so Im probally approching mid 50s actual with the TTBT.

I put it back down at 2800 @ 1.375 and going to let it prime overnight and see how it goes.

Do you guys thing watercooling would get me that magic 3Ghz?
 
I think water would give you just enough to get that extra 80-100mhz. Popping the top may also but only do that if you feel comfortable doing so.
 
2800.jpg


Leaving it here to prime overnight. I'm going to bed.

Thats @ 1.375, It needed the small bump.
 
Spazilton said:
Well 2800 @ Stock did 30 min or so seemed to be going fine.

I found out I was having a lot of my problems because I kept the chipset at 1.5. A bump to 1.6 has greatly helped stability. I was getting wierd stuff like on a lockup the boot screen would be corrupted until a cold reboot.


2825 Fails after a coulpe of minutes. I think you are going to beat me with the watercooling. Going to prime another 1hr and then start adding some voltage.
Click to expand...


so adding voltage to chipset actually does something?
 
Can someone check the TcaseMax and TDP values of these Opteron 165 (CCBBE 0610PMVV)? I am trying to see if the Tcase and TDP values mean (potentially) higher OC'ability.

My OC-friendy CCBIE 0608 has much higher values than the so-so 0551.

Optrn 180, JH9-E6, 49°C, 1.35V, 35.0W
Optrn 165, JH9-E6, 51°C, 1.35V, 45.0W - CCBWE 0551UPMW
Optrn 165, JH9-E6, 63°C, 1.35V, 105.0W - CCB1E 0608MPMW


Software:
http://www.thecoolest.zerobrains.com/forums/viewtopic.php?t=83
 
buzzly said:
Can someone check the TcaseMax and TDP values of these Opteron 165 (CCBBE 0610PMVV)? I am trying to see if the Tcase and TDP values mean (potentially) higher OC'ability.

My OC-friendy CCBIE 0608 has much higher values than the so-so 0551.

Optrn 180, JH9-E6, 49°C, 1.35V, 35.0W
Optrn 165, JH9-E6, 51°C, 1.35V, 45.0W - CCBWE 0551UPMW
Optrn 165, JH9-E6, 63°C, 1.35V, 105.0W - CCB1E 0608MPMW


Software:
http://www.thecoolest.zerobrains.com/forums/viewtopic.php?t=83
Click to expand...
57°c 1.35v 75w ccbbe 0610dpmw priming now at 2744 as it failed at 2800 stock, tonight I'll take it up and see what we can get :D
my ccb1e 0606vpmw was rated at 63°C 110.0w, it did 2.8 at stock voltage but doesn't like any extra voltage at all.
 
I get the same tcasemax. Priming still at [email protected], failed after an hour 35mins last time but still going this time. 1hr 35mins is still good enough for me, only on core 1 so I likely won't have any problems
 
repoman0 said:
I get the same tcasemax. Priming still at [email protected], failed after an hour 35mins last time but still going this time. 1hr 35mins is still good enough for me, only on core 1 so I likely won't have any problems
Click to expand...
yeah I've got another one that will be here monday, so then I'll decide which to keep, looks like the 0606 is gone definatly though, as this things outdoing it with the ihs on. it did 2.8 for an hour and 5 minutes then failed on core 1, hopefully one will hit 3 without issues. what did yours top out at or have you not put any volts to it?
 
Mine froze after 10mins at 3GHz 1.475v, so it should be fine at 1.5. But I didn't continue to prime as PWM temps went up to 75C, another fan is coming on monday

Though I tried to get over 3GHz, 3042 was a no go even with 1.6v.. might have been too much voltage, maybe it will do best at 1.55 or something. I will test more once I get my pwm fan
 
So the TCasemax and TDP values do make some sense. I know there are many factors involved in OC, such as packaging, cooling and others.

But if you look at the data, the Tcasemax/TDP, especially the TDP value, do make some senses.

Optrn165, JH9-E6, 63°C, 1.35V, 105.0W - CCB1E 0608MPMW Prime 2.83g Stock
OPTERN JH9-R 63°C , 1.35v, 110.0w ccb1e 0606vpmw 2.8g Stock
Opteron165, JH9-E, 57°c 1.35v, 75w ccbbe 0610dpmw - Prime 2,74g Stock voltage


My other not OC-friendly stepping.

Optrn 165, JH9-E6, 51°C, 1.35V, 45.0W - CCBWE 0551UPMW 2.7g @ 1.47v
 
;)
buzzly said:
So the TCasemax and TDP values do make some sense. I know there are many factors involved in OC, such as packaging, cooling and others.

But if you look at the data, the Tcasemax/TDP, especially the TDP value, do make some senses.

Optrn165, JH9-E6, 63°C, 1.35V, 105.0W - CCB1E 0608MPMW Prime 2.83g Stock
OPTERN JH9-R 63°C , 1.35v, 110.0w ccb1e 0606vpmw 2.8g Stock
Opteron165, JH9-E, 57°c 1.35v, 75w ccbbe 0610dpmw - Prime 2,74g Stock voltage


My other not OC-friendly stepping.

Optrn 165, JH9-E6, 51°C, 1.35V, 45.0W - CCBWE 0551UPMW 2.7g @ 1.47v
Click to expand...
I don't think I'd use it as an absolute as my ccb1e 0606vpmw didn't do but 2.6 on stock voltage with the ihs still on. but there definatly is some merit to it. ;)
 
I think I know why mine won't do over 3GHz, forgot to change the ldt multi to 2 :rolleyes: Probably why it kept freezing at anything over 333 htt. Oh well, 2844 at stock is stable for almost 3 hours now compared to 1.5 last night, must be the AS5 setting in.
 
You must log in or register to reply here.
Back
Top