• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Recent content by yomerol

  1. Y

    Rookie: Diagnosing possible failure in HDDs

    Thanx for the reply!, And sorry for the enormous delay! Here's the output of the lspci command: []# lspci 00:00.0 Host bridge: Intel Corporation 5400 Chipset Memory Controller Hub (rev 20) 00:01.0 PCI bridge: Intel Corporation 5400 Chipset PCI Express Port 1 (rev 20) 00:05.0 PCI...
  2. Y

    Counting the number of threads in my processor

    Hi, I'd like to get some advice in the following: I have this output from lshw (on a centos machine): lshw -c processor *-cpu description: CPU product: Xeon (Fill By OEM) vendor: Intel Corp. physical id: 3b bus info: cpu@0 version...
  3. Y

    Rookie: Diagnosing possible failure in HDDs

    Hello everybody I've been asked to diagnose a possible failure in the HDD of one server and I'd like to get a little light on this topic. What I've been told is that there's an unusual flashing in the server's leds, and one of the possibilites is a bad disk drive. I also been told that the...
  4. Y

    RAID 1 in Supermicro Server.

    Hello everyone! I tried to set up a raid1 array using virtualbox and I was sugested to try on hardware instead. I'm attaching screenshots at almost every step I perform since I'm not sure which would be the point of failure and give you guys better visibility in case you would like to...
  5. Y

    RAID 1 in Virtualbox 4.2

    Thanx a lot leeleatherwood! This thing I wanna do is for experimentation only, What I tried on Vbox was creating the VM (RHEL type) and create 2 virtual HDDs (.vdi format) for this virtual centos instace (and tried somehow to RAID 'em before instalation, and install the actual OS on top)...
  6. Y

    RAID 1 in Virtualbox 4.2

    Hi, I'm trying to setup a RAID 1 array on a CentOS host using Virtualbox 4.2. What I'm trying to do here is to create the array using only the virtualization software (Vbox Interface) and not during the installation of the guest OS (all documentation/videos/blogs I've visited ). I...
  7. Y

    RAM for X9SCL-F

    Hi guys! I'd like to get some advise on the placing of memory modules on a Supermicro X9SCL-F (in a 5017C-LF server) motherboard, currentlyit has 3 installed memory modules (8GB each) for a total of 24 Gb of RAM, looking at the memory slots I observe the following branding: DIM1A DIM2A...
  8. Y

    ESXi 5.0 Compatibility advice

    Many thanx, I'll check out some other card options, any suggestions?
  9. Y

    ESXi 5.0 Compatibility advice

    Hi! I'd like to know if drivers are needed for the following HW in ordet to run ESXi 5.0 on it. Barebone server: SYS-5017R-WRF (X9SRW-F, 815TQ-R500WB) it appears on the compatibility guide: http://partnerweb.vmware.com/comp_guide1/detail.php?device_cat=server&device_id=22020 also...
  10. Y

    RAID 1 in 5017C-LF

    Hi! I'm adding an extra hdd to a 5017c-lf(X9SCL-F, 510L-200B)server so I can set up a RAID 1 disk array , I'm not using any extra controller since one of the onboard product features is: SATA 6x SATA 2.0 (3Gbps) w/ RAID 0, 1, 5, 10 How can I find out which driver is suitable for the...
  11. Y

    unable to see all interfaces on Vsphere 5.0 on supermicro SS5017C-LF server

    Hi guys! I'm using a SS5017C-LF server, with Supermicro X9SCL(+)/X9SCM board. It has 4 network adapters (2 built in and the AOC-SG-i2 card which features 2 additional interfaces). I installed VMware Vsphere ESXi 5.0 but I can't see all of the interfaces. And vshphere client only...
See more
Back
Top