ASUS Rampage VI Extreame

Lucky75

Limp Gawd
Joined
Jul 22, 2020
Messages
143
Hello guys,
I want to use I9 10980xe Cpu with ASUS R6E motherboard.
How much memaory I can use in that case ?
Is there any issues with that motherboard and CascadeLake-X?
 
Just make sure that the BIOS version on that motherboard is recent. You see, the R6E requires BIOS version 2002 or higher in order to use the Cascade Lake CPUs on that board. If for some reason you have an earlier BIOS version, you will need to find an older, 7000- or 9000-series X-platform CPU in order to perform the BIOS flashing.
 
What about overclock ?
Too many variables there. In general, the more cores, the less that the CPU will overclock in the first place. It also depends on the other factors, such as CPU and case cooling. There is no getting around that.
 
Hello guys,
I want to use I9 10980xe Cpu with ASUS R6E motherboard.
How much memaory I can use in that case ?
Is there any issues with that motherboard and CascadeLake-X?

The motherboard itself has only been tested to use up to 128GB of RAM. When it came out, all the available CPU's for that board only supported 128GB of RAM. Support for 256GB of RAM didn't arrive until Cascade Lake-X. In theory, Cascade Lake-X would support 256GB of RAM on the RVIE, but there are no guarantees. Memory compatibility comes down to a lot of factors. If you stick to 128GB or less, you'll be good to go. If you want to run more than that, I'd suggest a newer X299 motherboard or one that's been confirmed to support 256GB.

Just make sure that the BIOS version on that motherboard is recent. You see, the R6E requires BIOS version 2002 or higher in order to use the Cascade Lake CPUs on that board. If for some reason you have an earlier BIOS version, you will need to find an older, 7000- or 9000-series X-platform CPU in order to perform the BIOS flashing.

This is factually incorrect. While 2002 or later is required to support Cascade Lake-X, the RVIE does not even need a CPU installed to flash the BIOS.

What about overclock ?

What about it? While your mileage may vary, but you are looking at around a 4.7GHz maximum overclock if you use a really good (and larger) AIO. With custom liquid cooling 4.8GHz or greater is possible. With loads like Cinebench R20 and Prime95, you'll see temperatures near the throttling point which for that CPU is 110c. I've seen 105c-109c doing just that with a decent waterblock (EK Velocity RGB) and 480mm and a 420mm radiator. That CPU will clock slightly higher, but only if you aren't trying to use AVX512 based workloads or run tests that create slightly unrealistic heat conditions.

Too many variables there. In general, the more cores, the less that the CPU will overclock in the first place. It also depends on the other factors, such as CPU and case cooling. There is no getting around that.

This is a gross over simplification of things. While you aren't incorrect in general terms, this isn't strictly true with Intel's Cascade Lake-X CPU's. According to Intel, there are "small dies" and "large dies" when it comes to Cascade Lake-X and its predecessors. Essentially, the larger ones are binned better and can often provide better overclocks than the smaller ones. The 10 or 12 core is the cut off for that. The 14 and 18 core CPU's aren't hindered by their extra cores in this case beyond that they are more demanding on the VRM's and cooling solution. However, you don't exactly find poor VRM's on X299 boards. They were always spec'ed to support 18c/36t CPU's like the 7980XE right from the start. The cooling is up to you. However, if you really want to overclock it, you will need a top tier AIO or a custom loop to do it.
 
Sticking a fan using the included bracket works pretty decently on the RVIE
 
I have this board. It is currently running an 10940x in a Fractal Design R5. I installed a fan on the top of the case to help cool the VRM. Otherwise, it does get quite hot. ASUS UEFI is good, but like someone else noted, make sure you update the UEFI to the latest version but not the 2002 version. I had that version and it was running the CPU voltage at 1.5 (on auto). Not good.
 
I will try to ask more clear questions. I buyed that CPU from one guy with ASUS R6E Omega and there it was running at 5 GHz at 1.3 volts.
I am asking did I can do the same OC with my old motherboard ?
 
What is your motherboard, cooling solution, and case? What is the cpu that you are currently running?
 
. However, you don't exactly find poor VRM's on X299 boards. They were always spec'ed to support 18c/36t CPU's like the 7980XE right from the start. The cooling is up to you. However, if you really want to overclock it, you will need a top tier AIO or a custom loop to do it.


actually.. this board has a notoriously poor VRM for overclocking the 18c chips.. hence the omega update and added active cooling on the VRM heatsink.

if your gonna go for a mild overclock even (as low as 4.3ghz allcore and 1.15vid) make sure you use active cooling to prevent VRM throttling.



 
I will try to ask more clear questions. I buyed that CPU from one guy with ASUS R6E Omega and there it was running at 5 GHz at 1.3 volts.

I'm skeptical about such a claim based on what I've seen those CPU's do.
 
I'm skeptical about such a claim based on what I've seen those CPU's do.
i am also

OP
did he mention how massive a radiator he had attached to it?

because at 1.3v on my 10980xe im totally cpu throttling even with a 420mm x 60mm radiator and custom waterloop. i have a 1260mm radiator (and 4 200mm fans) comming in a couple weeks to do the much hyped 5ghz all core and finally tame the thermals.. but without MASSIVE cooling its simply not happening.
 
i am also

OP
did he mention how massive a radiator he had attached to it?

because at 1.3v on my 10980xe im totally cpu throttling even with a 420mm x 60mm radiator and custom waterloop. i have a 1260mm radiator (and 4 200mm fans) comming in a couple weeks to do the much hyped 5ghz all core and finally tame the thermals.. but without MASSIVE cooling its simply not happening.

I used a 420mm and a 480mm and couldn't get the temps that low. Granted, I had the GPU in the same loop, but it wouldn't generate all that much heat doing benchmarks that tested the CPU alone. The issue comes down to the fact that the surface area of the die, heat spreader and TIM are all bottlenecks for cooling. You can't just throw infinite radiator space at it and expect to tame the 10980XE. It just doesn't work that way. Also, the voltages required to stabilize it at 5.0GHz all core don't help. At 1.3v, my test sample from Intel would only do 4.8GHz all core with the above radiator configuration. 4.7GHz is about all it could manage on the same board using a 360mm radiator setup and an older waterblock design.
 
And I thought my 10700k with full load temps of 84c with 2x360MM were bad.
 
I used a 420mm and a 480mm and couldn't get the temps that low. Granted, I had the GPU in the same loop, but it wouldn't generate all that much heat doing benchmarks that tested the CPU alone. The issue comes down to the fact that the surface area of the die, heat spreader and TIM are all bottlenecks for cooling. You can't just throw infinite radiator space at it and expect to tame the 10980XE. It just doesn't work that way. Also, the voltages required to stabilize it at 5.0GHz all core don't help. At 1.3v, my test sample from Intel would only do 4.8GHz all core with the above radiator configuration. 4.7GHz is about all it could manage on the same board using a 360mm radiator setup and an older waterblock design.

i know it. the cores might not have 5ghz in them no matter what i do short of extreme cooling and voltage, but having a ridiculous rad will help compared to what i have now. the 10980xe is in its own loop with a heatkiller block and KPx paste and said rad i mentioned before. i can add liquid metal to the IHS on that chip also to help thermal transfer
. i have a 7980xe here also so i can try direct die cooling to get temps more incheck of using a soldered chip doesnt work out. i dont 100% full expect to get any of the 18c chips i have up to 5ghz STABLE. but im gonna do my damnedest. If it doesnt work out how id like ill use it to run the GPU as close to ambient room temp as i can. or maybe hook it up to my 10900k direct die system (70c max 5.3/4.8 ghz 1.5v set 1.33get after 10 linpack loops)

bottom line is ill find something fun to do with it. throwing more RAD wont solve the heat issue completely, but it will help as much as possible, well without going the chiller/phase change cooling route.
 
Last edited:
I have Monoblock and 420 + 560 + MO-RA3 420 (3x420 mm) so my cooling should be ok. But that motherboard is old and not so good like Omega and that is the reason for that post.
 
I have Monoblock and 420 + 560 + MO-RA3 420 (3x420 mm) so my cooling should be ok. But that motherboard is old and not so good like Omega and that is the reason for that post.
ohh dude i wanna see! but 5ghz on the 1st gen rampage vi will be rough. not impossible with the monoblock but probably still rough. sounds like we will have a very similiar set up all said and done. i have a 360x60 420x60 and the 1260mm rad comming in a couple weeks (been on back order since july was told easly sept delivery) and i have the newer rampage VI with the new monoblock from EK.. im not using that block RN but i might throw it on.

anyways i wanna seeeee pics!
 
This is factually incorrect. While 2002 or later is required to support Cascade Lake-X, the RVIE does not even need a CPU installed to flash the BIOS.
I stand mostly corrected on this. What I had stated was based on my own experience with some of the other motherboards that I had owned in the past. Some of those would not even POST at all with a newer CPU than what was supported.

And I stand corrected on the ASUS ROG motherboards. These have a USB port that is assigned to flash a newer BIOS (or even a BIOS version that is older than what can be flashed under normal means) whenever the system is powered off. So yes, the ROG motherboards do not even have to be powered on (but just merely plugged in) to flash a newer BIOS version.
 
Last edited:
I stand mostly corrected on this. What I had stated was based on my own experience with some of the other motherboards that I had owned in the past. Some of those would not even POST at all with a newer CPU than what was supported.

And I stand corrected on the ASUS ROG motherboards. These have a USB port that is assigned to flash a newer BIOS (or even a BIOS version that is older than what can be flashed under normal means) whenever the system is powered off. So yes, the ROG motherboards do not even have to be powered on (but just merely plugged in) to flash a newer BIOS version.

Basically, any motherboard with a BIOS flashback feature should be able to do it as they have a specialized ASIC that does everything required to make it work. Every ROG board I've ever reviewed or looked at had this capability as do many others. The ASUS X299 Prime Edition 30 is another example of a motherboard that has this capability. On Intel boards, it's common to have this feature through the entire mid range. Even some lower end (not bottom of the barrel) boards have this capability. On the AMD side where you really need it, the feature is less common.
 
Basically, any motherboard with a BIOS flashback feature should be able to do it as they have a specialized ASIC that does everything required to make it work. Every ROG board I've ever reviewed or looked at had this capability as do many others. The ASUS X299 Prime Edition 30 is another example of a motherboard that has this capability. On Intel boards, it's common to have this feature through the entire mid range. Even some lower end (not bottom of the barrel) boards have this capability. On the AMD side where you really need it, the feature is less common.

Oddly on x399 its on every board I can think of. Bummer it was only supported for a gen and a half. It did save my bacon once. So I guess I should be glad it had it. But yea it should have been a no brainer. But those mobo vendors wanna sell new boards. Not keep people on old ones. Arg
 
Oddly on x399 its on every board I can think of. Bummer it was only supported for a gen and a half. It did save my bacon once. So I guess I should be glad it had it. But yea it should have been a no brainer. But those mobo vendors wanna sell new boards. Not keep people on old ones. Arg

There is a very good reason for that. X399 isn't like the other platforms. Motherboard manufacturers weren't sure if Threadripper would succeed in the HEDT market the way Ryzen did in the mainstream segment. Motherboard makers weren't ready to go all in on a bunch of motherboard models at various price points. This is why each motherboard maker only produced one or two models of X399 motherboard's initially. Also, given the price of the chipset and requirements for Threadripper, they decided not to go cheap.
 
x399 has a pretty good commitment for the future too, supposedly.

No, it doesn't. Socket TR4 is dead. It was replaced with the electrically incompatible sTRX4 and the TRX40 chipset.
 
  • Like
Reactions: E4g1e
like this
No, it doesn't. Socket TR4 is dead. It was replaced with the electrically incompatible sTRX4 and the TRX40 chipset.
History repeats itself, in this instance:

Intel also changed a few pins when it introduced its Coffee Lake (8th Generation) CPUs in late 2017. In both instances, the CPUs physically fit directly into their predecessor sockets, but attempting to operate such a system would result in a failure to even POST.
 
No, it doesn't. Socket TR4 is dead. It was replaced with the electrically incompatible sTRX4 and the TRX40 chipset.
Fuck, forgot that wasn’t the chipset for TRX40. Spent too many hours reading about them.
 
History repeats itself, in this instance:

Intel also changed a few pins when it introduced its Coffee Lake (8th Generation) CPUs in late 2017. In both instances, the CPUs physically fit directly into their predecessor sockets, but attempting to operate such a system would result in a failure to even POST.


but you can mod z170 /z270 to boot cfl/cfl-r
 
Back
Top