DAN A4-SFX: The smallest gaming case in the world

No, it shouldn't... Anyway, I made a little mock-up with cardboard to get custom cable lengths and I was looking at my SF600 PSU thinking, there's a lot of wasted space down there once I have the more manageable custom cables...hmmm. A 120mm cooler wouldn't fit so I started to see if there was a 92mm AIO cooler on the market and there is!

I'm not sure if this will work now or not based off the 50mm measurement, but I found this tiny AIO manufactured by Asetek. As many as you know Asetek basically invented the AIO cooler. They manufacture all of Corsair's and NZXT's coolers to this day. The rad is 92 x 92 x 30 with no fan... I thought if I were to fabricate a fan window where the SSD/HDD mount is, maybe I could liquid cool this beast out the bottom! I mean it's still possible I suppose. 60mm would have been a lot better, but with some minor modding/slim fan it could work! The only downside to this of course is figuring out a way to get air around the mainboard. But there could be a fan suspended above the heatsink via threaded sleeve nuts/standoffs coming off the mounting hardware... I dunno. Just an idea as I researched the best form of cooling. Thoughts? It's hard when you don't have the case in front of you... I feel like I'm forgetting about something that might cause interference...

Or you could use a small GPU, like a 1070 mini or an R9 nano :)
 
As an eBay Associate, HardForum may earn from qualifying purchases.
Theres even a mini zotac 1080 which may work just as well.

Personally if it were me though, i'd be thinking more along the lines of modding the side panels so that you could mount radiators externally for both the cpu and gpu
 
Also seen Thermalright AXP-100RH , 51 mm cooling tower.

http://www.thermalright.de/en/cooler/66/axp-100-rh?c=9

Here i think you must take away metalplates for fan mounting and grind down it a bit on the top otherwise it will not fit the Case.

And i think you must come on solotions after the way to get this optimized.
if you grind it down, it will have the same problem as C7 causing turbulence (see posts before). It's actually better to leave ~10mm of free space. Otherwise if you don't mind the turbulence just use C7.
 
if you grind it down, it will have the same problem as C7 causing turbulence (see posts before). It's actually better to leave ~10mm of free space. Otherwise if you don't mind the turbulence just use C7.

It will be set up just like the nexus 7000 that dondan showed us. The fan will go underneath the heatsink so the turbulence will be lessened significantly. The turbulence is caused by the pre cut circular holes on the case itself not being aerodynamic as opposed to hex holes.

He should be fine.

On another note. If anyone decides to use a different fan for the thermalright axp-100 I'd buy their ty-100 fan. I also have a bnib a9x14 i could trade.
 
More on CPU cooling in Dan A4-SFX

Unfortunately Cryorig C7 was a bit over-hyped. Although it does cool well at full speed, it is a clear loser in terms of performance / noise + you get an annoying high-frequency turbulence due to the fan spinning close to the side panel.

My recommendation for the best performance / noise:
1) Silverstone AR05 (36.7mm) - a clear winner
2) Noctua L9i (37mm) - if you want more compatibility, as it doesn't have the wide heatpipe of AR05 (95mm x 95mm vs AR05's 104mm x 92mm)
3) Cryorig C7 (47mm) - if you want some room for overclocking, as it cools better at full speed, but it is also much louder
4) Something custom if you have the time and energy to do it yourself

Some other coolers compatible with the case, which don't seem to offer any advantage:
Alpenfohn Silvretta (45mm) - inferior to C7, L9i and AR05
Xigmatek Praeton LD963 (45mm) - inferior to L9i and AR05
Phanteks PH-TC90LS (45mm) - inferior to L9i and AR05
Raijintek Zelos (44mm) - inferior to L9i and AR05
Cooltek ITX30 (30mm) - inferior to AR05, about the same as L9i, but wider (100mm x 94mm vs L9i's 95mm x 95mm)
Intel Boxed Cooler - ewww

Sources:

C7 turbulence demonstration by Meccabolix:
Sure, here you go:



Idle fan speed = 930rpm

Then i did an instant jump to

100% fan speed = 2500rpm

Then i put the side cover on and did the same

No idea what the dB's are as i don't have the equipment to measure it. But the high pitched spinning when the side cover is on sure is annoying :p


L9i vs C7 performance in Linus video:


Screenshot of capped noise, which shows L9i having superior performance / noise:
L9ivsC7_performance_per_noise.PNG


Note that C7 does cool better if you uncap the speed:
L9ivsC7_temp.PNG


Note the video above includes AR06, not AR05. It also shows Phanteks PH-TC90LS inferior to L9i.

AR05 review shows it is superior to L9i. You can also see Cooltek ITX30, which is inferior to AR05 and about the same as L9i:
http://www.nikktech.com/main/articl...ow-profile-cpu-cooler-review?showall=&start=5

AR05 better performance:
AR05vsL9i_temp.jpg


AR05 lower noise:
AR05vsL9i_noise.jpg


This is also consistent with Dan's cooling test before, AR05 is better than L9i (without customization):
https://hardforum.com/threads/dan-a...-in-the-world.1799326/page-55#post-1041652691

Alpenfohn Silvretta inferior to C7:
http://www.tech-review.de/include.php?path=content/articles.php&contentid=16637&page=6

Xigmatek Praeton LD963 inferior to L9i:
https://www.hardwarebbq.com/intel-6...raeton-apache-iii-and-intel-stock-cooler-2/8/

Raijintek Zelos inferior to L9i:
https://elchapuzasinformatico.com/2014/02/review-raijintek-zelos/5/

I currently own C7, but I will replace it with AR05 because I cannot tolerate the turbulence (not as bad if you remove the side panel, but common).

Cheers ;)
 
Last edited:
anyone who has a dancase or ncase to sell in reasonable price in Europe pls PM me
Thx in advance
 
Yeey,

I've got my system installed in the A4-SFX. Migration from my Hadron-Air case was a breeze. The system is much quieter now, I liked the Hadron-Air a lot, but the location of the GPU was not perfect, being squashed against the PSU. And the "custom" server style PSU in the Hadron was also a bit of a pain. No modular cables and a whiny 40mm fan. Moreover, the A4-SFX has more space for the GPU so I have more choices when upgrading.


Installation remarks:
- Having two hdds (or ssds) in the bracket doesn't work well with the corsair sata power cable connectors. I had to split the ribbon cable into a 2wire and 3wire part and bend each side in a loop to individual directions (left and right) to force the power connectors on the drives.
- When mounting a drive on the front position, the power cable has to pass besides it. There is not enough space for it to go on top of the drive. For me I routed it along the USB side, since the power button side was already crowded with 2 PCIe power cables. Since I figured this out near the end, I had to disassemble a lot to reroute the cable.
- Cables are a bit messy, especially the 24pin ATX cable. I had the feeling it was a bout 80mm too long for my mobo, which has the connector directly on the side of the PSU. The area directly underneath the PSU is completely filled with cables now. However, the mobo area and the GPU area look incredibly clean.
- The noctua cooler is running at 10% fan speed when idle and never exceeds 30%, it's performing well. The GPU is the most audible both in idea and while gaming, but it is much less loud than in my previous case.


Specs:
intel 4770 + noctua L9i (original fan)
asrock Z87E-ITX
evga GTX 770
corsair SF450
corsair ram 16GB
samsung 840 pro 256GB
samsung 850 evo 1TB
seagate hdd 2TB (15mm)
 
Sadly I can't get the Nexus from anywhere because it isn't produced anymore and all vendors are out of stock.
I know that the AXP-100 RH won't just fit inside like that but I will just make it fit.
I think I will do the same, I think I can take enough off the top fins without reaching the heat pipes and damaging them. At very least I could fit an a9 underneath then but ideally with a bit more modification I could get a slim 120mm underneath. Depends on ram clearance but I suppose the 120mm fan doesn't need to be centered on heatsink, I think it should cool really well. Hope it will get AM4 compatibility!
 
Here is fast made drawing how to mod the Nexus Low 7000 R2:
low-7000r2drawing_0xoc4udq.jpg

Does any body knows the part number of the Noctua anti-vibration mounts used in the Nexus mod or any similar alternatives ? and from where I can get these rubber / silicon mounts ?



31b0458b4b.jpg
 
For everyone who bought the Cryorig C7:

I purchased the 14cm slim C7 fan linked a few pages back. It will arrive tomorrow. I am going to zip tie it to the c7, take before and after temp readings, take some pics, and share the results with everyone.

I don't have my Dan A4 yet. Regardless, if the temps and/or noise improves then the results should transfer over to the Dan A4.
 
Last edited:
Hey, If there's anyone with a GTX 1080 founders installed in their Dan Case, can you let me know what temps you're getting please?

I'm debating whether or not to keep the FE card or go for something like the EVGA ACX 1080. Better cooling is the only reason - I don't be overclocking much.
 
https://imgur.com/a/pgFgP
I got a massive 20C drop with my Skylake CPU after delid.
Cooler: Cryorig C7 on PWM
CPU: i7-6700K
TIM replacement: Grizzly Conductonaut
Test run: Prime95 26.6 Small FFT for ~10 minutes

Awesome results! I plan on deliding whatever processor I end up with. Did you use Conductonaut between the heatspreader and c7 as well? Also, please post what overclocking results you get with the delid and c7...

Are you going to be moving to a different cooler?
 
More on CPU cooling in Dan A4-SFX

Unfortunately Cryorig C7 was a bit over-hyped. Although it does cool well at full speed, it is a clear loser in terms of performance / noise + you get an annoying high-frequency turbulence due to the fan spinning close to the side panel.

My recommendation for the best performance / noise:
1) Silverstone AR05 (36.7mm) - a clear winner
2) Noctua L9i (37mm) - if you want more compatibility, as it doesn't have the wide heatpipe of AR05 (95mm x 95mm vs AR05's 104mm x 92mm)
3) Cryorig C7 (47mm) - if you want some room for overclocking, as it cools better at full speed, but it is also much louder
4) Something custom if you have the time and energy to do it yourself

Some other coolers compatible with the case, which don't seem to offer any advantage:
Alpenfohn Silvretta (45mm) - inferior to C7, L9i and AR05
Xigmatek Praeton LD963 (45mm) - inferior to L9i and AR05
Phanteks PH-TC90LS (45mm) - inferior to L9i and AR05
Raijintek Zelos (44mm) - inferior to L9i and AR05
Cooltek ITX30 (30mm) - inferior to AR05, about the same as L9i, but wider (100mm x 94mm vs L9i's 95mm x 95mm)
Intel Boxed Cooler - ewww

Sources:

C7 turbulence demonstration by Meccabolix:


L9i vs C7 performance in Linus video:


Screenshot of capped noise, which shows L9i having superior performance / noise:
View attachment 16960

Note that C7 does cool better if you uncap the speed:
View attachment 16961

Note the video above includes AR06, not AR05. It also shows Phanteks PH-TC90LS inferior to L9i.

AR05 review shows it is superior to L9i. You can also see Cooltek ITX30, which is inferior to AR05 and about the same as L9i:
http://www.nikktech.com/main/articl...ow-profile-cpu-cooler-review?showall=&start=5

AR05 better performance:
View attachment 16959

AR05 lower noise:
View attachment 16958

This is also consistent with Dan's cooling test before, AR05 is better than L9i (without customization):
https://hardforum.com/threads/dan-a...-in-the-world.1799326/page-55#post-1041652691

Alpenfohn Silvretta inferior to C7:
http://www.tech-review.de/include.php?path=content/articles.php&contentid=16637&page=6

Xigmatek Praeton LD963 inferior to L9i:
https://www.hardwarebbq.com/intel-6...raeton-apache-iii-and-intel-stock-cooler-2/8/

Raijintek Zelos inferior to L9i:
https://elchapuzasinformatico.com/2014/02/review-raijintek-zelos/5/

I currently own C7, but I will replace it with AR05 because I cannot tolerate the turbulence (not as bad if you remove the side panel, but common).

Cheers ;)


I ordered the cooltek LP53 and a9x14 this morning, then saw your post, then ordered the Silverstone AR05 based on the noise results and temp results lol

the AR05 is coming tomorrow, i'm going away in the evening for a few days but i should be able to get a video out before i go and hopefully some temp results too.

I should have the LP53 and a9x14 when i come back on the weekend, i'll do a vid of those aswell, i may even switch and swap the fans on each cooler to see which is the quietest and has better cooling if people wish. ( i guess i could even bring the pc with me and do the tests when i go away haha)
 
The Evga should be cooler and quieter. I've got a MSI RX 480 and the fans only spin 50-100rpm higher with closed side panel. So it doesnt even get much hotter then a open case
 
Can anyone that's purchased some custom cables for this case from Cablemod please provide the lengths you ordered and other custom specific details?

I'd like to place an order too but don't have all my parts yet to do the measurements.
 
Can anyone that's purchased some custom cables for this case from Cablemod please provide the lengths you ordered and other custom specific details?

I'd like to place an order too but don't have all my parts yet to do the measurements.

I ordered 150mm ATX, 300mm EPS and PCI-E. Buy at your own risk, I can't guarantee those will work. EPS and ATX are highly dependent on where the connectors are on your board. I have an Asus z270i.
 
Is there anyone playing around with a ASUS Impact mobo. (VI, VII, VIII)?
I have the Impact VIII it feels like its one of the hardest to cool in that case.
Because of that mosfitwall I thinking of buying an full Cu cooler and put on somekind copper heatpipes that goes to the top.

Edit: It would be nice to see which mobo ppl are using on the Google spreadsheet.
 
Last edited:
FYI, there's a Nexus cooler on Amazon Italy https://www.amazon.it/Ventola-Nexus-Low-Profile-1366/dp/B001RI7TZS/ for anyone located near there... not sure if they ship international. I found one on Amazon Japan last night, sold by Amazon (who ships international), and ordered the last one... there is another listed on the japan site, but for like 4x what I got mine for.
 
As an Amazon Associate, HardForum may earn from qualifying purchases.
Is there anyone playing around with a ASUS Impact mobo. (VI, VII, VIII)?
I have the Impact VIII it feels like its one of the hardest to cool in that case.
Because of that mosfitwall I thinking of buying an full Cu cooler and put on somekind copper heatpipes that goes to the top.

Edit: It would nice to see which mobo ppl are using on the Google spreadsheet.
was thinking of adding heat pipes as well, ive no experience and im only going to try if all the other coolers aren't enough
 
I think I will do the same, I think I can take enough off the top fins without reaching the heat pipes and damaging them. At very least I could fit an a9 underneath then but ideally with a bit more modification I could get a slim 120mm underneath. Depends on ram clearance but I suppose the 120mm fan doesn't need to be centered on heatsink, I think it should cool really well. Hope it will get AM4 compatibility!
As suggested before it would be easier to replace the 7mm mainboard standoffs with 5mm an just not use an IO shield. That would gain you more than enough room for the AXP100RH without any grinding.
 
I ordered 150mm ATX, 300mm EPS and PCI-E. Buy at your own risk, I can't guarantee those will work. EPS and ATX are highly dependent on where the connectors are on your board. I have an Asus z270i.

Perfect! Thanks. I have the Z270i.. or will have when I pick it up in California next week. Waiting for me....
 
As an Amazon Associate, HardForum may earn from qualifying purchases.
I ordered 150mm ATX, 300mm EPS and PCI-E. Buy at your own risk, I can't guarantee those will work. EPS and ATX are highly dependent on where the connectors are on your board. I have an Asus z270i.
oh and by EPS- did you get 4 pin, 8 pin, or 4+4 pin? Sorry, first time doing this. Complete noob here.
 
Is there anyone playing around with a ASUS Impact mobo. (VI, VII, VIII)?
I have the Impact VIII it feels like its one of the hardest to cool in that case.
Because of that mosfitwall I thinking of buying an full Cu cooler and put on somekind copper heatpipes that goes to the top.

Edit: It would be nice to see which mobo ppl are using on the Google spreadsheet.

I got a Asus MAXIMUS VIII IMPACT and I don't have any issues cooling that board or the CPU ...
I'm using a Noctua NH-L9i to cool my i7 7700K. Haven't overclocked that much, but didn't have any issues with a 15% overclock.
(yes, at first I locked the CPU fan at 40% RPM, hit 100°C when playing Doom for a while, but after setting the CPU fan to automatic again I got a decent 72°C after a Doom session.
 
oh and by EPS- did you get 4 pin, 8 pin, or 4+4 pin? Sorry, first time doing this. Complete noob here.

4+4 but I don't think it matters if you need 8 pins, to just get the 8 pin. I just got exactly what the SF600 comes with.
 
Updates on US shipping? Its been 2 weeks since it was thought US shipping would be processed. What is the current progress?
 
No last weekend. Last week Monday to Friday there was a delay because of German Customs. Please read my updates on Kickstarter.
 
Back
Top