Flexible Risers in Second Slot under Two Slot GPU?

Zarathustra[H]

Extremely [H]
2FA
Joined
Oct 29, 2000
Messages
42,484
Hey all,

Has anyone ever seen a flexible riser that would fit in a pinch like this?

When I switched to SLI I had to pull my 10Gig ethernet adapter, due to the board layout.

I would really like to use it again, but my options are to kick one of the GPU slots down to 8x (which I really don't want to do) or to figure out how to use one of the slots hidden underneath a GPU.

My thoughts are if there were something like an L-shaped riser, with a flex cable on the end of it it could work, it's just that I've never seen one!
 
you could use a PCIe ribbon cable, but then you would need to figure out your own mounting

like the cables in this photo taken from the mod gallery
11896198_10153543199910140_5081493847068783043_o.jpg
 
Yeah, I don't want to suspend the GPU in the air above the slot.

I was hoping something flexible or thin and with a right angle existed, so the GPU can sit in the slow like it normally does, and the flexible riser can run from the covered slot under the GPU to a location for the NIC...

It's so annoying that lanes are limited. -E just isn't enough.

In an ideal world every CPU would come with enough lanes to provide full 16x capability to 8 PCIe slots.

So 128 PCIe lanes + a few for the chipset.
 
So using any of the black slots will kick the lane configuration down to 16/8/8? Isn't lane distribution determined by the device connected? I remember plugging my sound card into a PCI-E x16 slot once and it was only using one lane while my video card still got the full 16 with a 16 lane non-E CPU.
 
I have 4 1x to 16x riser cables, 3 of which I modded to have power over a molex. They are basically these: (newegg)
What you could do is route those to another spot in the pc and hook your 10g gigabit card up. I would assume that you are using a low profile capable card? If so you could just install that bracket then hook the riser up and the screw the card down to the case. That might work, or you could mod some kind of bracket to hold it in place if it wiggles to much.

If you need one or 4 hit me up ill sell them cheap. I guess one thing to consider is if the cards exceed 1x pcie 3.0 bandwidth (most likely not), then you might need to go to a 4x or 16x, but video cards at 4x are usually 95% capable.
 
I have 4 1x to 16x riser cables, 3 of which I modded to have power over a molex. They are basically these: (newegg)
What you could do is route those to another spot in the pc and hook your 10g gigabit card up. I would assume that you are using a low profile capable card? If so you could just install that bracket then hook the riser up and the screw the card down to the case. That might work, or you could mod some kind of bracket to hold it in place if it wiggles to much.

If you need one or 4 hit me up ill sell them cheap. I guess one thing to consider is if the cards exceed 1x pcie 3.0 bandwidth (most likely not), then you might need to go to a 4x or 16x, but video cards at 4x are usually 95% capable.

I would need an 8x version, but thanks!

So can you confirm that this design will actually fit in the slot under a full height GPU?

I have a fairly good idea how I'd hook up the NIC, its the whole "male end of the riser fitting under the GPU" thing I'm not sure about.
 
Question. I thought the slots that get covered by a dual slot card share the lanes with that 16x slot.

Am I mistaken?
 
Question. I thought the slots that get covered by a dual slot card share the lanes with that 16x slot.

Am I mistaken?

That depends very much on your motherboard.

Mine is laid out like this:

- Slot 1: 16x (or 8x if Slot 2 is used)
- No Slot
- Slot 2: 8x if used (see slot 1)
- Slot 3: 4x no matter what.
- Slot 4: 16x (or 8x if Slot 6 is used)
- Slot 5: 4x no matter what
- Slot 6: 8x if used (see slot 4)

So right now I have 16x-16x SLI in slots 1 and 4
Nothing in slot 2 (to maintain 16-16)
Slot 3 contains my Creative X-Fi Titanium HD
Slot 6 is unused (again, don't want to lose 16-16)

So this leaves slot 5, a 4x electrical 16x slot, which is completely covered by GPU2.

My 10gig NIC is an 8x Gen2 card, but according to my calculations the bandwidth from 4x should be sufficient to saturate it.
 
our system vendor gets all the risers for our systems from adexelec

How much room is under the vid card to get to that PCIe slot?

I probably have a 90 right angle x16 adaptor I can sell cheap, I can measure the height if you want, probably also have some of the ribbon extenders, but they are all straight ends, not 90'
 
Back
Top