RackMount Questions

Status
Not open for further replies.

EvilAlchemist

2[H]4U
Joined
Jan 11, 2008
Messages
2,732
Need a little help // knowledge about rack mount setups.
I purcahsed these units last week.
evilracks.jpg


I know / or think i understand how to mount the rackmount cases in the front of the rack.

How do you attach the back of the case to the other support posts
(These have 3 -- front - middle - back)

I have seen sliding rails for chassis.
Is there a way to support the back without sliding rails - like a permerant mount?

Is the necessary hardware included to back support // or are most only front supported?

Hope that makes sence.
 
It depends on the case.
No. Unless it came from IBM, it doesn't include rails. No, you don't get them with the rack. No, you don't even usually get the screws with the rack.
Most cases people here buy don't even come with rear extenders, or have them available. Many times, they're simply not needed, but if you've got cheap steel tongues up front, they'll bend or the back of the case will dip. Or both. But hey, at least most of them take universal rails. The problem being that universal rails tend to cost ~$100 or more by themselves.
EDIT: I took a look today. Universal rails are effectively dead. You get to guess at your screwhole distances, then play merry hell with flimsy sliders that I wouldn't trust to hold up an empty 1U. Ugh.

Oh, and the mid supports are somewhat unique, and only for short devices like KVMs and switches. I never use them when I have them available, because they're impossible to work with once everything's installed.
 
start at the bottom and build up if you have heavy stuff and no support rails for the back.
just put some pennies on the outside edges of the top of the previous topmost case and build up using the pennies as load bearing transfers from case to case as you build up.

secondly rails are immensly helpful if you need to pull a case out and tinker inside such as a ram upgrade or failure analysis/replacement. they save you having to tear apart your rack to get the offender out to just look at it.
 
If your rackmount cases are too heavy to be safely supported by only the front tabs, you can use some plumbers tape (the metal band with holes from a hardware store) to secure the rear of the case. I have several 2U cases that are supported fine via only the front mounts, but all my steel 4U's are mounted this way. I just take two peices of the tape, secured to the rear sides of the case, and then use regular cage nuts & bolts to secure the other end to the rear posts.
 
Rails are pretty cheap on Ebay or use perforated steel pieces. Try P/N 8962K24 from mcmaster.com, and then figure out how to attach it to the rack.
 
A solid steel rod or steel square tube can be used to cross under the back of the system possibly?
 
First off .. i wanna thank AreEss for all his suggestions here and in PMs ..

I think my best course of action is to deck the racks out with shelves and use my current cases

I am planning on using something very close to this (I think my rack is deeper then 24 though)

http://www.server-rack-online.com/shv1924.html

I still need to go measure these rack and the depth .. but i think i can fix two systems per shelf .. with six boxen per rack ... this will be much cheaper then going with full out 4U cases + all the mods to my current setups that will have to be done..

Thanks to all for your suggestions
 
Most servers come with extend-able rails. All HP, Dell, Supermicro, and Sun servers I have seen come with these, and any old chassis or servers you buy should. The rack should have square holes, which threaded inserts can be clipped in the inside of the rails on the front and back. Then, the rails are placed attached using screws to those threaded inserts. Somewhat hard to explain in text, but easy once you see it...

Good luck.
 
Most servers come with extend-able rails. All HP, Dell, Supermicro, and Sun servers I have seen come with these, and any old chassis or servers you buy should. The rack should have square holes, which threaded inserts can be clipped in the inside of the rails on the front and back. Then, the rails are placed attached using screws to those threaded inserts. Somewhat hard to explain in text, but easy once you see it...

Good luck.

... wow, I want to live in your fantasy world where things actually work like that.

IBM: Rails included with late model xSeries only, not included with certain models.
Sun: "Oh, you want to put it in a rack? That'll cost extra." Exceptions only for the V1280/E2900 which require them to be safely installed.
Dell: "Rails, rails... oh, well, you have to buy a rack for that and then you have to buy..."
Supermicro: "Rails not included unless it says they are."
HP: "You have what kind of rack? Yeah, that'll be extra, because it's not our rack."
 
... wow, I want to live in your fantasy world where things actually work like that.

IBM: Rails included with late model xSeries only, not included with certain models.
Sun: "Oh, you want to put it in a rack? That'll cost extra." Exceptions only for the V1280/E2900 which require them to be safely installed.
Dell: "Rails, rails... oh, well, you have to buy a rack for that and then you have to buy..."
Supermicro: "Rails not included unless it says they are."
HP: "You have what kind of rack? Yeah, that'll be extra, because it's not our rack."

I had to lol at that one. I've been looking at building a boxen rack, I might do it if I had more money, but I don't. It wouldn't be cool to see someone build a 42U rack stuffed with 21 CPU/GPU folding boxen, water cooled of course (Swiftech MCR-320QP for each box).

And AreEss, are you running AIX on that big IBM H80?
 
I had to lol at that one. I've been looking at building a boxen rack, I might do it if I had more money, but I don't. It wouldn't be cool to see someone build a 42U rack stuffed with 21 CPU/GPU folding boxen, water cooled of course (Swiftech MCR-320QP for each box).

And AreEss, are you running AIX on that big IBM H80?

*shrug* Why would I waste the time and money on GPU trash? That'd be much like buying an IBM 7014-T42 and filling it with Dells, which would give you ~38U because of their nonstandard mounting idiocy. The real systems are usually 42 x 4-16C @ 32-128GB per, depending. I've done some smaller Cell assisted designs. Watercooling is a complete and utter waste, especially the Swiftech stuff, which has piss-poor space to BTU ratio, to put it mildly. I use T42's with the heat exchangers, which do 50K BTU/hr at zero-U.

And of course, what else is there to run on an RS64-IV system? (Answer; nothin'.)
 
I thought that Linux had been ported to RS/6000/System p. Guess I was wrong or it's only the really new stuff.

And I was talking about F@H, not serious HPC work where there is a better alternative to GPUs. I don't think anyone is going to spend the money to build a serious watercooling setup that you'd see in HPC. We've got a couple Neslab chiller units at work (something different, but same principal) and they probably suck down more power than most people's whole F@H setup. Not to mention you'd have to do a lot of HVAC work to expel all the waste heat. Probably not something people would do in their home.

Something like that is a good idea where space is at absolute premium, but that's not what I was talking about at all. I was just talking about alternatives to piling ATX mid-towers in your closet.
 
SUSE and Red Hat will run on Power5/6. I'm not certain about prior to Power5. I don't know if it is possible to use other flavors of Linux, but those are the two that IBM supports in terms of virtualization, code porting, etc.
 
Running Linux on an RS/6000 or POWER is like running your car on Windows ME. Sure, you can, but are you stupid enough to want to? Also there's the fact that RS/6000 alone contains three major processor families and over 20 sub-models. The H80 is an RS64-IV based system, vastly superior to anything short of the high end POWER5, and some features of POWER6 are from the RS64-IV, like BCD.

I don't really do anything but serious HPC work. Never considered it. I don't want the electric bills with these systems, or anywhere near them. You're talking about 42,000 watts of draw at 120V. Even at 220V, it's over 100A per cabinet. *shudder* My electric bills are high enough with the one Peregrine/AGSW (Advanced Graphics System, Watercooled) which I only boot as needed, and has two dedicated 20 amp circuits - each power supply of the four total is rated at 1650W.

Reason I like the IBM doors, by the way, is because they're the cheapest to integrate. You build a cabinet to spec, take out your 50K BTU, size your A/C. Waste heat goes down insulated hot water lines, and quite literally, a bunch of radiators and ginormous fans is sufficient. You don't need a super expensive water chiller, depending on your loads. Even at maximum load for a row of 5 cabinets - that's 250K BTU/hr BTW - I can design for just one medium sized chiller. It doesn't take a lot to bleed 50K BTU/hr in your plumbing, pushing you down to 200K BTU/hr. Even at 250K BTU/hr, you're still well within air cooled condensors.
 
1) Have an interest in HPC.
2) Spend way too much time learning about it.
3) Be completely out of your mind - THIS IS A REQUIREMENT!
;)
 
What's the point of having a rack if you're rigging crap to hold up your servers.

Let me emphasize... "hold up your SERVERS."
 
Status
Not open for further replies.
Back
Top