The Lian Li Gallery

No tubing, pump, res, rad, different PSU (sleeve), different case with different HDD rack...

You're point? Just b/c he has water cooling doesn't mean it still can't have good cable management. Plus you can't really see what he has in the first place b/c of all the wires.

You = excuses...excuses...excuses :p
 
Plus you can't really see what he has in the first place b/c of all the wires.

Lian Li PC-V1100B Plus II case, modified for tube to exit via case rear.
eVGA 680i A1
QX6700 cooled by DTEK FUZION
8800GTX KO ACS3 SLI watercooled under EK 8800GTX blocks
4GB G.SKILL DDR2 800 cooled by Corsair Dominator fan.
2x WD Raptor 150GB RAID 0, 2x Samsung Spinpoint T 500GB, occupying lower hard disk rack.
PC P&C Silencer Quad 750W, which uses unsleeved molex and S/ATA power connectors because PC Power and Cooling is lazy.
X-Fi Elite
...and a LOT of wires.

Water loop:
some sort of 5" bay reservoir -> Swiftech MCP655 D5 Vario -> EK block 2 -> EK block 1 -> PA120.3 with radbox and 3 unsleeved Yate Loon fans -> DTEK FUZION cpu block.... with no tubes attached to it.

Front view, case lighting on:

(The gray tube on the left is part of the desk, and the gray/black box sitting on edge is an external hard-drive case.)

Sexy....
 
You're point? Just b/c he has water cooling doesn't mean it still can't have good cable management. Plus you can't really see what he has in the first place b/c of all the wires.

I agree. I'm a firm believer that any type build can be done with excellent cable management.
 
Ok...here is mine as an example:



It's not hard...just time consuming.

Is that the Artic Cooler Freezer 7 pro? is there anyway you cold do me a favor and measure how far it sticks out from the edge of the mobo. I'd really appreciate it.
 
I agree. I'm a firm believer that any type build can be done with excellent cable management.

There are some cases out there that make clean wiring a bi%*h...but I agree that for the most part it is possible for almost any build, maybe just not always up to standards that I hold for example. ;) :D
 
@ everyone criticizing my lack of cable management: I'll work on it when I feel like it. Right now it isn't causing a problem. It's not restricting airflow and the case is window-less, so I don't see it as a priority.
 
Is that the Artic Cooler Freezer 7 pro? is there anyway you cold do me a favor and measure how far it sticks out from the edge of the mobo. I'd really appreciate it.

Sure...but I'll have to do it tomorrow. I just got home and I have some work to do before I go to bed. Off the top of my head though...I think there is at least a good 2 inches from the top of the HSF and th case sidepanel. Plus that is with sound absorption material on it.
 
Did you turn the back-panel fan around from stock, so it's an exhaust? Or are the Freezer 7 Pro and the back-panel fan blowing against each other?

That picture was taken before I realized that my temps were 20+ degrees higher then what they should have been. I flipped the HSF and back fan around 180° and it fixed the problem.

So now fresh air is pulled from the back, then both the back fan & CPU fan push air towards the front and finally the front fan pulls the air out...just like it was designed to do. My temps dropped back to normal after that fix (oh and I applied fresh thermal paste to the HSF as well so that might have helped solve the problem as well.)
 
Sure...but I'll have to do it tomorrow. I just got home and I have some work to do before I go to bed. Off the top of my head though...I think there is at least a good 2 inches from the top of the HSF and th case sidepanel. Plus that is with sound absorption material on it.

Hmm, well nvm. I can tell just by looking at that pic that it won't fit in my v1000. If it sticks out more than a quarter inch from the edge, it won't fit. Thanks anyway, and nice setup.
 
Ok...here is mine as an example:

http://farm2.static.flickr.com/1361/892074597_13c413d1a3_b.jpg[/IMG

It's not hard...just time consuming.[/QUOTE]

[quote="buffbiff21, post: 1031329483"]No tubing, pump, res, rad, different PSU (sleeve), different case with different HDD rack...[/QUOTE]

exactly.

not to mention that it looks like your airflow is going opposite to what the case design is.
 
@ everyone criticizing my lack of cable management: I'll work on it when I feel like it. Right now it isn't causing a problem. It's not restricting airflow and the case is window-less, so I don't see it as a priority.

nice job regardless, I remember when I watercooled my v1000 the rad was obstructing the power plug

how did you overcome that problem?
 
exactly.

not to mention that it looks like your airflow is going opposite to what the case design is.

Ever heard of the "scroll" feature? 2 posts above the one you left I explained that I fixed the problem.

I know scrolling is "difficult" to do but you should give it a shot some time... :p
 
nice job regardless, I remember when I watercooled my v1000 the rad was obstructing the power plug

how did you overcome that problem?

Simply by my choice of power supply :)
psustuff008di7.jpg
 
Simply by my choice of power supply :)
psustuff008di7.jpg

Well I think you did a nice job. Few questions,

How is that power supply any different? It looks like it would be the same depth as any other? Can you show an example of it plugged in?

I'm going to water cool my case soon and have a swiftech MCR220 rad that will be hung on the back like yours and need some advice as to how everythign fits. And with that tripple rad hanging off the back, how do you plug all your other cables in? (usb/dvi/etc) Is that a radbox or fan hanging off the back?

and how did you get your power button illuminated, thats just sick. Is that a v1100 feature?

Anyways, enough questions for you to ponder, here's my rig + my laptop lol

computer.jpg
 
Hey dr4gon I love your setup there... similar to mine, but your desk is WAY more tidy... great looking rig as well... but I might be a little biased.
Anyway... that switch that invalidbuffalo has, that you asked about, is a Bulgin vandal switch if memory serves me right... they come in many colors and styles as well. They fit perfectly in the Lian Li V series cases without modification too, if I'm not mistaken. Plus, I agree, they just look sick on a Lian Li. I have my eye on a red ring Bulgin right now.
You've inspired me to clean my desk now.

Anyway, here's my setup... please excuse the messy work area... yeah, right, like I really "work" there... rather I say, play area...
DSC03757P.jpg


DSC03748P.jpg
 
The red theme you got there is pretty sweet...especially the blood red cooling fluid for your water cooling :D

I'd maybe ditch the cliche chick silhouette though...;)

...and I gotta ask...what's with the gun?
 
Thanks jag...
The red coolant is just Zerex and distilled water with some red food coloring... would you believe it, red food coloring contains propylene glycol? Hmmm... anyway... cools real good though.
And as for the little chick, she's just sitting there... in no way attached... I really don't know why I put her there... but she'll be taking a hike when I finish modding this thing... I'm not quite done with this rig yet. I was actually thinking of replacing the clear Lexan with some red Acrylic for the window.
And the gun... that's my favorite Airsoft gun. What can I say, I like shooting plastic bullets at things. The real one's under my pillow.
 
@ everyone criticizing my lack of cable management: I'll work on it when I feel like it. Right now it isn't causing a problem. It's not restricting airflow and the case is window-less, so I don't see it as a priority.

Ah whatever, I've got my sights set on a V1100 too, and I'm so happy to see one in this thread finally.

Mine will be air cooled, so not as busy as yours and I've got a modular PSU picked out (going to be removing that middle divider to do it of course) so that'll help a ton, and no SLI and that's pretty much it...

I'm basically moving my current machine to a Lian-Li case based on the Asus P5N32-E SLI Plus, and powered by the Corsair HX520 PSU.

The case is as expensive as both the other components combined.. hehe.

Where'd you get yours? NewEgg?
 
Propylene Glycol is an ingredient often found in anti-freeze.
Also known as C3H8O... makes an excellent liquid for heat transfer.
Now, what it's doing in red food coloring... I have no clue.
 
Hey dr4gon I love your setup there... similar to mine, but your desk is WAY more tidy... great looking rig as well... but I might be a little biased.
Anyway... that switch that invalidbuffalo has, that you asked about, is a Bulgin vandal switch if memory serves me right... they come in many colors and styles as well. They fit perfectly in the Lian Li V series cases without modification too, if I'm not mistaken. Plus, I agree, they just look sick on a Lian Li. I have my eye on a red ring Bulgin right now.
You've inspired me to clean my desk now.

Anyway, here's my setup... please excuse the messy work area... yeah, right, like I really "work" there... rather I say, play area...

Nice setup you got there. Lol your not messy at all. I just happened to snap a picture when my desk was the least messy. What probably happened was that I pushed everything on the floor... :D

As for the switches, dammmn, those are nice! Looks like a mac, lol

http://www.pcextreme.com/catalog/case_accessories/switches.html

They're easy to hook up? Is the stock switch using those same plugs? Where do I draw power from to power the light?
 
Thanks dr4gon...
those switches should be very easy to wire up in theory... I've not done it personally.
But all the switch part would need is 2 wires, which you could just pull from the back of the Lian Li switch and wire to the new one. As for the LED in the new switch, I'm not 100% sure of what voltage it runs on, but I'm sure it would be simple to find the proper source to power it.
I wanted to get one and use the LED ring on it as my HDD activity indicator. It may be as simple as cutting your current power LED off of the wires and using the wire going to your motherboard now to power it...??? This is how I replaced my stock blue Power LED on the V1000 with a red one.
Wait a minute, I just looked on that site you linked to... it says you need a resistor inline to run the light from the motherboard's 5v or from the power supply's 12v.
Hmmmm... how about this...
http://www.performance-pcs.com/catalog/index.php?main_page=product_info&products_id=4056
These are pre-wired... and should be as simple as plugging it in to the proper pins on your motherboard... I would assume the resistor is prewired as well. They cost a bit more though.
Seeing as how this is a pretty popular Lian Li mod however, I bet you can search around and find a tutorial or something of the sort. These switches are definitely sweet and well worth the trouble to get one up and running though. I apologize for my lack of information on 'em... I'm gonna learn though. I'm sure one of these Lian Li enthusiasts on here has some knowledge on the subject.
 
Thanks dr4gon...
those switches should be very easy to wire up in theory... I've not done it personally.
But all the switch part would need is 2 wires, which you could just pull from the back of the Lian Li switch and wire to the new one. As for the LED in the new switch, I'm not 100% sure of what voltage it runs on, but I'm sure it would be simple to find the proper source to power it.
I wanted to get one and use the LED ring on it as my HDD activity indicator. It may be as simple as cutting your current power LED off of the wires and using the wire going to your motherboard now to power it...??? This is how I replaced my stock blue Power LED on the V1000 with a red one.
Wait a minute, I just looked on that site you linked to... it says you need a resistor inline to run the light from the motherboard's 5v or from the power supply's 12v.
Hmmmm... how about this...
http://www.performance-pcs.com/catalog/index.php?main_page=product_info&products_id=4056
These are pre-wired... and should be as simple as plugging it in to the proper pins on your motherboard... I would assume the resistor is prewired as well. They cost a bit more though.
Seeing as how this is a pretty popular Lian Li mod however, I bet you can search around and find a tutorial or something of the sort. These switches are definitely sweet and well worth the trouble to get one up and running though. I apologize for my lack of information on 'em... I'm gonna learn though. I'm sure one of these Lian Li enthusiasts on here has some knowledge on the subject.

Nah, your fine I understood completely.

What would be cool is if you had one of these

303596_1.gif


A little bit more interesting and also lit.

wow nice case plyr, which model is that one of the a107 or on of those other mini towers?

I can't wait to get my watercooling pics up as soon as I assemble it, should be within the month.
 
Nice lighting! Care to show us a full view (as opposed to a side view)?

Where are you getting the window for your panel btw?

I got the case @ performance pc, they just forgot to put on the window so I sent the panel back to them to get it modded.

Here's more pictures, wires still a little to messy for my taste, need to get more zip ties :)

DSC01133.jpg

DSC01130.jpg

DSC01125.jpg

DSC01107.jpg

DSC01143.jpg
 
Messy? That looks pretty tidy to me! The wires on the side behind the drive bays you never see anyways.

I was hoping you would say something other then Performance PC b/c I can't seem to find any sites that sell pre-modded standalone panels for the A05B. :(
 
or you can cut one yourself unless you're like me who don't own dremel or can cut a straight line hehe.
 
or you can cut one yourself unless you're like me who don't own dremel or can cut a straight line hehe.

You sir are correct! :D Plus something as nice as a Lian Li case (which is my first one btw) I wouldn't want to ruin it...especially when its basically impossible to find replacement panels in the first place.
 
just man up, and get it donE!

:rolleyes: I must admit, I'm in the same boat, except I do own a dremmel and can cut farily decently. Just don't want to hurt my baby. Gonna have to though to make a few holes to allow for water tubes to pass through.
 
just man up, and get it donE!

:rolleyes: I must admit, I'm in the same boat, except I do own a dremmel and can cut farily decently. Just don't want to hurt my baby. Gonna have to though to make a few holes to allow for water tubes to pass through.

:p Sure and I'll have you send me the money for each time I need to buy a new panel or case.
 
hey dr4gon, where'd you find that power button with the power logo on it that you posted?
That would be so awsomely wicked if it lights up red.
 
I got the case @ performance pc, they just forgot to put on the window so I sent the panel back to them to get it modded.

Here's more pictures, wires still a little to messy for my taste, need to get more zip ties :)

http://i58.photobucket.com/albums/g252/azn_plyr/DSC01133.jpg[IMG]
[IMG]http://i58.photobucket.com/albums/g252/azn_plyr/DSC01130.jpg[IMG]
[IMG]http://i58.photobucket.com/albums/g252/azn_plyr/DSC01125.jpg[IMG]
[IMG]http://i58.photobucket.com/albums/g252/azn_plyr/DSC01107.jpg[IMG]
[IMG]http://i58.photobucket.com/albums/g252/azn_plyr/DSC01143.jpg[IMG][/QUOTE]

lol...you got the same stickers in the same spots as me on the front.
 
D0h! Now I gotta peel them off now. . . . :D

haha yeah. the zalman one would have been a C2D one but i couldn't peel it off well enough from my previous case :( one of these days i'll replace it with a C2Q sticker though ;)
 
Here's my attempt @ cable management... but I still gotta find a good place for that pesky little temperature probe wire...
DSC03779800x600.jpg

The thing in the top drive bay is my homemade temperature display... I just used the Lian Li 3.5" bay adapter as the housing for it. It has smoke black acrylic so you can't see anything when it's off, just blends in with the case sort of. And the fan controller, I just took a Thermaltake fan controller, ripped it apart and modded one of the Lian Li 5.25' bay covers to hold it so everything looks like it belongs on the Lian Li... well, except for my stupid DVD drive... gotta figure out how I wanna do that next.
DSC03758800x600.jpg

You'll note that all my cables ended up in the bottom chamber of the case... friggin' Seasonic PSU has so many wires! But I removed some junk, and moved the front HDD cage back and to the right a bit so the HDD cables would plug in nicely on the left side.
I think I might cut some better panels for the interior to hide everything.
I am not 100% satisfied with something, but I'm not sure what it is yet... but something's gotta change!
I'm about to build a new desk that matches the Lian Li pefectly, and I just got an external HDD enclosure that looks like it belongs with the V1000 too... so I'll be sure to post pics when I get the new stuff setup.

Oh yeah and, plyR... you got skills with the cable management I must say. Very clean and classy. I like it. And that case is just sexy. But then, I've never seen a Lian Li I didn't like.

Well, until when is then... later
 
Back
Top