Wow...I messed up.

Spike

Limp Gawd
Joined
Dec 7, 2004
Messages
350
I have the msi k8 neo 2 platnum and it was reading my ram as pc 2700 so i went into the bios and set it to 3200 it rebooted and now it freezes at the post screen just after it does its memory test (it says the memory is ok) i cant get back into the bios cause it is frozen. Does this mean ill have to flash the bios??? reformat and install xp or is there some other way. if i do have to flash the bios does anyone know where id get the dl from how i can tell its the right one and how to do it. ive never done it before and ive heard if you mess up it can even screw the mobo up so bvad it needs to be sent into the manufacturer. I appreacieate your time reading this and thanks in advance.
 
unplug everything, remove the ram, plug the board back in without ram try to boot, then unplug put ram back in and reboot.
 
if that doesn't work, try getting into the bios with no ide devices attached, if that works you can make sure everythign is ok then reconnect the ide stuff
 
would it matter at all if i left my usb stuff plugged in??? Is it just the power i need to unplug??? or absolutely everything. forgive me for being lazy but its kindof a pain to unhook everything so i wanna make sure if its nessecary or not.
 
i unplugged everything than plugged in just the mobo thrned it on to the expected beeping than thurnd it off and hooked up the ram and powered it up. this time to less expected resaulte. it poweres on for less than a second and shuts down i checked all my connections it was all hooked up right so i unpluged my powersupply to let it resert itsself and tried again, to the same resault.
 
Pull out the cmos battery. Let it sit for a bit. Put it back in. Turn it on.
 
I just tryed my spare powersupply. it did the same thing so 1 thing eliminated. i didnt think that was what was wrong but good to be sure.
 
ok ill try it i think i must have screwed up the bios but i have no clue why that would make it restart.
 
bios didn't reset properly. pull the cmos batt out for an hour with the comp unplugged (and the psu disconnected just to be sure) and then put it back in.

if it won't boot, you'll have to trick it into going into bios... try booting w/o hard drive.

if that doesn't work, you'll just have to borrow someone's pc3200 stick long enough to get it to boot so you can fix the bios.
 
Spike said:
ok ill try it i think i must have screwed up the bios but i have no clue why that would make it restart.
Just follow everyone else's advice who is telling you to remove the CMOS battery for 10min or set the clear CMOS jumper. It will fix your problem.
 
As for borrowing a stick of ram i could just jack 1 from the comp im on now but im thinking the batt thing will work i removed it and am now waiting/regreating pulling my comp apart lol.
 
read the mobo manual man, it says how to reset the bios. i bet its even got pretty pictures that point to the cmos clear jumper.
 
ive almost read it cover to cover. i must have missed resetting the bios with the jumper however i did read about resetting the bios. as i stated above it was frozen and i couldnt get in. i have the manual here and ill see if i can find if it has a manual resett but id think i woulda caught it.
 
Dioretsa said:
Why can't he just clear the bios using a jumper?

Because no one listen to a noobie... LOL!!! nah seriously though.. i would agree with Dioretsa.. first thing i would have done is clear the CMOS.. that's gotten me out of many jams...
 
yeah in retrospect now that i think about it that is the logical thing to do i just didnt know about using the jumper so as far as i knew the only way to reset it was through the bios which was frozen. not that it matters anyway i did try it and had no diffrence.
 
Spike said:
ive almost read it cover to cover. i must have missed resetting the bios with the jumper however i did read about resetting the bios. as i stated above it was frozen and i couldnt get in. i have the manual here and ill see if i can find if it has a manual resett but id think i woulda caught it.
PULL OUT THE BATTERY!




Do you think he'll notice it this time? :p
 
Try hitting the insert key right after you turn on the computer. On the k8n neo, it sets the ram to 166mhz.

Try this before yanking the battery.
 
Just reset the CMOS man.. damn.. simplest thing.. could save all the work... then go for the battery after that... then try that inset key thing the other dude said..
 
i will repeat what everyone said..

1. hold insert key on keyboard then push the power button on the computer (this should start it with all automatic and safe settings)

2. if that didn't work. put the reset jumper to "clear".. then turn on the power with it set as reset.. turn it off.. put the jumper back to normal.. (some motherboard are wierd and need it started in "clear")

3. if that didn't work.. pull the battery out for an extended period of time.. maybe try step 2 also..

4. borrow a stick of faster ram.. set the ram to auto then put yours back in..
 
lol I yanked the battery and left it out for 20 min with the powersupply unpluged from the wall and mobo. hooked it all up and still just restarted I figured i may not have left it out long enuff though i doubt it so i have it out now. i also used the juper to clear the cmos. and yet again same problem.
 
Spike said:
lol I yanked the battery and left it out for 20 min with the powersupply unpluged from the wall and mobo. hooked it all up and still just restarted I figured i may not have left it out long enuff though i doubt it so i have it out now. i also used the juper to clear the cmos. and yet again same problem.


intersting.. if you can get a hold of some faster ram for testing.. do it! .. also.. make sure everything is connected to the mother board correctly.. that's one that gets even the most experienced
 
Oh by the way im not quite the idiot you guys seem to think i am . i have been reading your replies and suggestions and trying them, i havent been replying cause theres not much to say. i tried clearing the cmos, i tried removing the battery (infact its out now im trying it a second time) momentarily i will try the insert key thing. On a change of note i was actually very surprised on how much help/sugestions ive gotten and i appreacieate it all very much. so thanks.......and I AM LISATENING?READING LOL!!!! (also crapping my pants cause i spent 3k on this Comp and if it doesnt run all i have to show for it is a noisy fan box)
 
RancidWAnnaRIot said:
intersting.. if you can get a hold of some faster ram for testing.. do it! .. also.. make sure everything is connected to the mother board correctly.. that's one that gets even the most experienced
Yea i know even if i did hook it up wrong once or twice ive unhooked and hooked it up like 8 times in the last 4 hours.
 
K it's official I've Done all of the following and nothing has worked.
scottatwittenberg said:
i will repeat what everyone said..

1. hold insert key on keyboard then push the power button on the computer (this should start it with all automatic and safe settings)

2. if that didn't work. put the reset jumper to "clear".. then turn on the power with it set as reset.. turn it off.. put the jumper back to normal.. (some motherboard are wierd and need it started in "clear")

3. if that didn't work.. pull the battery out for an extended period of time.. maybe try step 2 also..

4. borrow a stick of faster ram.. set the ram to auto then put yours back in..
 
did you try booting with only ram cpu, MB,

I have this board and sometimes funky things happen with the ide busses for no apparent reason, disconnect every ide cable from the mobo and try posting it
 
Did you try one stick of ram only?

Edit: Forget what I said. You tried that already.

How'bout a BIOS reflash? Do you have access to the latest BIOS? You'll have to copy a small .exe file to the floppy and reboot with the floppy in.

I did crash my BIOS once and I pulled both memory dimms out and tried to restart and then I put the memory back in and then it was able to boot. But the difference is my mobo has 2 BIOS chips, one for backup so idiots like me can revert back when I piss the mobo off trying to max the memory's mhz.
 
there is one other thing you can do... call the mobo company and buy a new bios chip. they're replaceable, fortunately.

:cool:
 
It may not be freezing because of RAM, make sure you have no peripherals connected. Disconnect floppy, CDROMs, Hard Drives, remove all PCI cards, etc. You should only have your CPU, RAM and Video card. If it tests the memory correctly, it might not be that.
 
Leave the battery out overnight witht he computer unplugged. That's what I had to do when I had my timings way too tight.
 
I do have a 3 year warranty. but id wrather figure it all out myself. i guess i just like to fix things myself. as for what k1pp3r said i have had the harddrives/ide devices unpluged throughout. I am actually emailing there customer service now explaining the problem and im going to see if they have any possible fixes and if not i think im going to rma. ive lost plenty of sleep oves some stupid little quirk in the bios allready (granted it may have been my fault in the first place) so i figure ill if the customer service cant figure it out ill rma and consider the $30 bucks on a 3 year warranty money well spent. and yet again i thank you all for your suggestions and if nothing else i have learned a little as to what to do just in case.
 
Shroomie said:
Leave the battery out overnight witht he computer unplugged. That's what I had to do when I had my timings way too tight.
actually i pulled it out before i went to bed and tryed this morning. same same.....im beginning to think i may have somehow burned out the board.
 
Back
Top