Weird USB Problem

J

jsilva

Guest
I have a PC with 8 on-board usb2 ports. All of the sudden for some reason only 1 port is working. To make things more weird, I cannot connect any device (mouse, flash drive, hard drive) directly to that one port. I have to use a usb hub -and then- anything that I connect works but It has to be through the hub. I use Win7 Ult 64-bit. I have not installed any suspicious software that may have cause this. This just happened out of the blue. I'm guessing is a motherboard issue, but damn I've tried everything from usb drivers, chipset drivers, enabling/disabling usb in the bios, removing and reinstalling usb controllers in device manager....any other ideas?!?!?! The only thing I haven't done is re-flash the bios, but I'm running a Raid-0 setup and I'm afraid I'm going to mess up my arraid by re-flashing. HELP!!!!
 
well if the usb ports have crapped out then its probly a motherboard issue. i had that on an old m2n-e and just one of the ports died....its still running though. backup your files. backup your files. first thing id try is a simple win7 isntall. just do it on a single hard drive, a spare if you have one. then test out the usb ports. if they are working then rebuild your array with the original drives. if not then you know the board is crapping out. my 2 bucks is on the board crapping out.
 
Off hand I cant think of anything else either other than to remove the Intel inf chipset driver and reinstall.

Reflashing the bios should not bother your array at all if you use the right bios for your motherboard.

Not having a backup for a raid 0 (no redundancy and 2x the change of disk failure is not a very good idea)

thats all I got. Try the chipset/INF reinstall, no joy with that and I would be thinking one of MSI's midrange P45 boards as a replacement. With a motherboard failure/change you are looking at big trouble with your raid if the replacement board does not use the same brand of raid controller chip. Unless you use the same kind of chip the array will almost certainly not be recognized and thus basically gone. I did a little research for you.

Your board uses (for the raid - the normal southbridge is Intel ICH7 DH )
SATA RAID 0/1/0+1
Additional RAID Controller JMB361

This is a Jmicon controller widely used by other manuf. Any board that uses a Jmicron JMB36x where x is just a version number should work and see your array right off the bat with no issues on a board swap.
Here is their web site
http://www.jmicron.com/Driver.htm

A lot of boards use that chip, unfortunately you will likely have to download the manual from the manuf site to double check. A lot of the Gigabytes use Jmicron chips (They call it a GSATA/fGigabyte SATA to hide the Jmicron heritage for primary raid where the Intel southbridge does not support raid and also secondary raid chip even if the board has the Intel raid southbridge. Perhaps you can find an exact replacement board cheap if someone has new old stock but if you had to spend $100 I would strongly consider biting the bullet and adding $30-50 and going with a P45 board. As long as the board uses a Jmicron JMB36"something" you should have no worries and could always shoot Jmicon a email to verify. Asus uses it also.

Anywho there is some info for you.
 
Thanks for answering guys. I have an image backup of my array (system partition) in 2 external locations. I use Acronis True Image. But then again unless I buy the exact same mobo my backup is useless. I'm going to try the chipset removal/reinstall and then go from there. Thanks for taking the time to help out. I appreciate it. :(

Ps: I found the same board for $50...If I get it, how do I work out my Raid-0 array issue?
 
Last edited by a moderator:
Back
Top