Venice 3500+ overclocking help needed by a uber noob

nealio

Limp Gawd
Joined
May 17, 2005
Messages
362
Heres the skinny,

I got a koolance system a while ago and I had it set up on a old Throughbread. Everything on that machine was watercooled exect the chipset fan. Wouldn't you know it the chipset fan went out and so did my mobo. Since I just got my taxes back, I figured I would upgrade. So now I'm running:

3500+ Venice
CMX512-3200C2PRO
A8N-SLI Deluxe
in a koolance case.

But for some reason I can't get it to post over 2870MHZ

I'm very new to the HTT stuff, so I spent the last couple of days reseaching it on your site. I read this thread, but some of the programs that he outlined didn't apply to me because the Clockgen tool didn't support my mobo. I also went thru and tried to understand the memory settings, but I didn't quite understand it too much.. Here is some screen shots:
cpuz_1_1.jpg


cpuz_1_2.jpg


cpuz_1_3.jpg


cpuz_1_4.jpg


Do you guys have any suguestions for this uber noob?!?!? I can't seem to get this to post over 3 and these guys with 3000+ are burning me. Cooling is not a problem I"m running at about 27C idle 31C maxed four hours on a prime95 test.

Thanks for your help!
 
I am by no means an expert - but I've been noticing a lot of people claim there's a theoretical architechture limit to the Venice (and other cores) of 2.7. People have been able to push the 3500's, 3700's, etc up to 2.8 and even up to 3.0 but not without a lot of stress and tight timings.

Then again, I may have misunderstood and be talking absolute BS - so don't rely on what I'm saying alone! :D

edit - from the cpu-z screenshots and my limited knowledge, it looks like you've got your HTT(FSB) : RAM Divider ratio's working right. The ram's running just a notch of 200mhz after the HTT has it's effect on it. Also - 2800mhz is nothing to sneeze at - but what's the stock speed on those 3500's again?
 
yeah I read your thread a couple times looking for an update, did you ever get that memory?
 
nealio said:
yeah I read your thread a couple times looking for an update, did you ever get that memory?

Not yet. I'm going to stick it out for a few more days with this crummy-poo ValueSelect stuff and if the new powersupply and cooling don't help matters, then it's time to exchange it.

On that note - one recommendation I have from testing this morning before work was voltages. Bump LDT & Chipset voltages up to the values recommended towards the tail end of my thread - and keep cpu and dram volts low to start. Ramp up as you go to test, and I've also had good luck with the DRAM +3v as well as the secondary VID setting (can't recall the name of it, but gives +XXX% over startup and cpu voltage if required). They seem to help keep the voltage at an even keel.

That is - if your motherboard supports it. Also - update your bios if you can, might very well give better support for Venice's and memory w/ Venice's.

edit - I know it has no real relevance to this thread, but in reference to my mention of the VID Special Control as per above - found a table with voltages (DFI boards) here .
 
anyone have any ideas of why this can't break 3??? :confused:

anyone? :eek:


I have cookies for the first person that can figure it out :p
 
nealio said:
anyone have any ideas of why this can't break 3??? :confused:

anyone? :eek:


I have cookies for the first person that can figure it out :p

It may very well be the ram limiting you (to a certain extent). I had a discussion with a Corsair employee about the Valueselect stuff a week ago, and he mentioned in passing that the C2 stuff (what you have, according to your cpu-z screenshot) is the exact same stuff - it just tested higher so they market it differently. In effect you're taking the same risk on potential whether you buy C2 or Valueselect.

That and I still feel it's an unfair assumption that you'll automatically get over 3ghz just because it's a 3500+. Remember, the guts in a 3000+, 3200+, 3500+ are really all the same (or so I've been told). So pushing higher than 2.7-2.8 will take a LOT of work, and not quite as simple as just telling it too.

Also - I really have no idea what type of an "overclocker" board that Asus board really is. Perhaps it's a board/settings limitation with the model/make/brand itself. A lot of really high OC's you're seeing on Venice's are on DFI boards (due to more configurability, higher voltage options, etc).
 
I dont see it breaking 3g's unless vapo/phase cooling. The chip is basically maxed in my eyes. where are these guys with 3000+ burning that score? Highest one here is 2853 or so for a 3000+.
read this article might give you some more info.
http://hardforum.com/showthread.php?t=904858
 
fenderltd said:
I dont see it breaking 3g's unless vapo/phase cooling. The chip is basically maxed in my eyes. where are these guys with 3000+ burning that score? Highest one here is 2853 or so for a 3000+.
read this article might give you some more info.
http://hardforum.com/showthread.php?t=904858

I've been reading a thread on DFI-Street on and off for the past few days, and it looks like "internet scuttlebut" has a lot of "overclocking noobs" posting their maximum overclocks on various forums (X-S was the most common culprit) with no hard proof evidence of being 3+ Prime stable for more than as long as it takes to snap a screenshot. End result has a lot of people who are still learning about Venice potentials assuming they can easily push 3+ on any of the Venice chips.
 
Did you establish your max overclock for each component?

What is the max bus your board can push?

Max memory overclocks?

Max chip?

Is your HTT link set to 2X or 3X, not 4X?

Find the max overclock of all of your components, then go for your system's max OC. If you do this, then you will know if it is your board, your memory, or your chip.
 
i have had 2 3200's and have 2 3500's all with different steppings. very very few 3500's are doing over 2800 without pc. stable water cooled should be around 2700 plus but only at at least 1.68 vcore. check out the venice database at xtremesystems.org hardware/amd forum. the second batch of 3500 does even lower. the 3000 and 3200 are hit and miss. some guys are getting 2800-2900 , most guys are getting 2400-2500. anybody planning on upgrading from a good winny (2700 or better) dont do it!. you will get much lower temps, but less bandwidth and probably lower htt. all the winchesters i had could do 330-340mhz htt but cant get 320 from a venice. save your cash, get the x2 4200+ 1mbl2 in a couple weeks.


very truly yours,
politenessman
 
I don't think your results are anything to scoff at. I think the Venice was way to hyped, it doesnt as huge of OC potential as everyone though. Most of them are doing 2.5-2.6 on air, 2.7-2.8 on water, and 3.0+ on phase change and other sub-zero coolers. If that overclock you posted is stable, your actually ahead of the game. You should refer to this thread to compare your results, there not all that off.

Do you by chance have the stepping of your CPU. Some OC better than others, as you can see by just the limited results in that thread. Perhaps you just ae not out of the best batch.
 
2.8 is about all youwill get on air. You need Phase to hit 3+....like me..wOOt! hehehe ;)
 
2Fresh said:
2.8 is about all youwill get on air. You need Phase to hit 3+....like me..wOOt! hehehe ;)
yeah 2fresh is a hacker using p.c. :p
:drool
 
Back
Top