Urgent! Backplate question

Pipo

Gawd
Joined
Jan 31, 2003
Messages
708
I'm making the transition to a new motherboard and on my old motherboard I was using a Tuniq Tower HSF. The backplate for this hsf had an adhesive square on it that got stuck to my old mother board and had to be cut to remove the backplate. Can I use this same back plate on my new motherboard without that adhesive square or am I going to short out my brand new motherboard?
 
If you're worried about it put a piece of cardboard in there but I have used them without anything.

I never remove the adhesive cover on those pads so they don't stick to the MB.
 
should of pulled out a hair drier and heated up the adhesive and slowly removed it..

but yeah a piece of cardboard should work.. you you could probably go to any crafts store and find the same double sided adhesive pads to replace whats on there now..
 
I would just do a trial run on your new board.
Make sure the backplate doesnt contact any solder joints or metal, if it does, put something non-conductive underneath it.

Many times the foam pad serves two purposes, adhesive and elevation off the MB surface.

I am of the same opinion as the others, I never peel the paper off the foam, the adhesive is very difficult to remove if you ever change your board out.
 
Cardboard will work, but I would also slap on a layer of good (3M) electrical tape over the backplate and look at the backside of the board for any sharp pointed "mountains" of solder and use a fingernail file to file off the sharp tip. It is critical you clean the board after doing this, wipe/brush off with unused new paintbrush and then wipe down with alcohol, don't want any solder dust hanging around.


Probably over kill but thats just me.
 
I never remove the adhesive cover on those pads so they don't stick to the MB.

That's a very good tip!
I've learned that one the HARD way (no pun intended).

I had an Asus P5B Deluxe that had severe chipset issues that had to be returned. And while I did warn the store gal (she's actually somewhat good as a technician... one of the best I've seen) that I had the thing stuck on the back, she went and sent the board to Holland (Asus' RMA center at the time), hoping they'd just fix it and return it.

BAD move. Long story short, I spent the best part of one and a half years trying to get my hands on a backplate, which I actually had to buy since she refused to take responsibility for the mishap. Once I found the bloody thing, though, I made sure NOT to peel the thing. That way not only I get to upgrade without a MAJOR headache, but I get backplate insulation.

To answer the OP, I'd advise you to at least put some cardboard between the board and the backplate, and make sure you won't start a fire with the setup BEFORE putting the system into production. You should be fine, but I wouldn't like to find I wasn't fine the hard way again...

Cheers.

Miguel
 
Here is what I have done on multiple systems... This also helps the mouting be more sturdy and keeps it from warping the board like it does when you use the stupid foam pads in the first place.

1. Go to your local hardware store and find some plastic/nylon spacers that are the correct size for the bolts that came with your mounting hardware... you will need 4 of them - 1 for each bolt. If your mounting hardware doesn't have nuts that go onto the bolts to hold the mounting hardware in place, you will also need 4 nuts to do this.


2. Make sure that with the spacers there is about 1/16" or so between the back plate and any solder joints sticking up on the back of the motherboard.. The idea here is to make sure that it is impossible for the backplate to short out anything on the back of the motherboard.


If something is shorting out or if there isn't visible room between the backplate and a solder joint... add a couple of those red insulating washers that usually come with computer cases to the spacers to bring the backplate farther away from the motherboard.... it is also a good idea to use these washers in between the motherboard and the nuts that hold the mouting hardware onto the motherboard.
 
Back
Top