Ultra-D Wont Post

dIsRuPtIvE

Limp Gawd
Joined
Dec 29, 2001
Messages
315
Well I have till Monday before I RMA my mobo so I figure I might post my problem here 1st and see if anyone has any insight.

Ok I've just upgraded my rig with the following parts:

Enermax 24pin 550Watt EG651P-VE
Koolance Exos Al
Athlon 64 3500+ (90nm)
nF4 Ultra-D
X800 XL

NOTE: I always turn my PSU completely off when connecting/disconnecting anything.

I seated the waterblock (CPU-300-H06) with AS5, using the new method by applying 1.5 rice grains worth and spreading with a 1 degree turn in both directions.

I then hooked up the Exos; easy as ever.

After jump starting the PSU and filtering the air from the Exos for approximately 10 minutes, I powered down and hooked up the HDD, Floppy, memory, and DVD.

Everything seems to fire up normally.

All fans run normally.

I get 4 lights and no less. DRAM and standby leds are all lit. I enabled the speaker but get no error code.

The Exos reads a steady temp of 73 degrees Fahrenheit


What I've tried:

I checked RAM seating and moved one stick to the 3rd slot from the 2nd

Cleared CMOS

jumpered for "safe boot"

attempted booting with all drives disconnected

Booting with my USB mouse disconnected as I read people had problems with USB

Only using 1 stick of RAM in the second slot.

Now the memory is in the 2nd and 4th slots


Any help is greatly appreciated.
 
i know this might not help, but how did you get an x800xl, and for how much?

can you describe more of what goes on when you try to power it up? do you hear a beep of some sort coming from the mobo? the only similar problem i had was when i was working on an asus a8v deluxe with a 3400+ s939 chip. the bios didnt recognize the cpu and so i had to reset the cmos, change the htt bus to 800mhz, and then flash it to latest bios. of course this wouldnt apply here since these are the new nf4 boards and they should be able to recognize your cpu.

oh btw, maybe this might sound insulting, but it doesnt hurt to double check the wiring, and making sure everything is seated nice and tight.
 
When I installed my new MSI K8N Ne02 plat, I knew the board worked, so I installed everything in the case and went to power it up, fans would spin for a second, then quit, I had to power off the power supply and turn it back on to get it to do that again. GRR, tore the mobo out of the case (I'm watercooled so that is a job for 2 men and a small boy LOL) put it on bench, powered up and posted. Great, I thought, I shorted out something when I screwed it down, no biggie, reinstall everything except I only use 3 screws to hold mobo to tray. still no post, exact same problem, GRRRRRR. So I strip out all 2 cards, reset power supply, hit the switch and whirrrrrrrrr, post and beep cause of no video, reinstall the vid card, hit switch and loud screaming BEEEEEEEEP, crap, plug in molex to vid card LOL, shut down and do that, system posts perfectly, seems the MSI mobo doesnt' like my criticool II relay board :( so the moral of the story is, expect the unexpected. and check everything, even stuff you know works in other machines, cause there is nothing wrong with the criticool II, the MSI board just doesn' t like it.
 
Ahh, it actually ended up being the 4 pin power connector next to the 24 pin. (just didn't hook it up). I looked for one on my PSU and didn't find it at 1st. Turns out the connector was hiding up in the top of my case. :D

I found out at the DFI forums that it is specifically responsible for powering the CPU. :eek:

Everything's runnin' smooth now. I just need some OCZ 3700 gold so I can make good use of this koolance, ;)

Specialist[X]
I let ZZF gouge me on the price for the XL. Still the best price/performance PCI-E out right now. Well if you like to play directx games that is:D . Aquamark: 68,485 http://arc.aquamark3.com/arc/arc_view.php?run=1762564231
 
Back
Top