Stuck at 3.55ghz--E6600

rsgunter

[H]ard|Gawd
Joined
Feb 24, 2007
Messages
1,325
My e6600 is stuck at 395 x 9. I can't get stable past that. Trying to figure out if I've hit my CPU limit. I've tried my ram at 4-4-4-12 and 5-5-5-15 at 2.25 and can't get stable.

Asus P5B Deluxe (newest bios)
E6600 -- Thermalright Ultra 120 @ 1.425
Crucial Ballistix ddr2800 @ 2.25

Temps under load running Orthos are around 45-48c.

CPU limit or am I missing something?
 
My e6600 is stuck at 395 x 9. I can't get stable past that. Trying to figure out if I've hit my CPU limit. I've tried my ram at 4-4-4-12 and 5-5-5-15 at 2.25 and can't get stable.

Asus P5B Deluxe (newest bios)
E6600 -- Thermalright Ultra 120 @ 1.425
Crucial Ballistix ddr2800 @ 2.25

Temps under load running Orthos are around 45-48c.

CPU limit or am I missing something?

u using coretemp or tAT? try TAT! because you seem to have the allendale version of e6600 .what cooling are you using?
 
I just bought the friggin' processor. Should be Conroe. I'm being lied too otherwise. :)

I used both Tat and Core temp. Tat says Pent M, don't know why though. :)

Temps-1.jpg



I'm using a Thermalright Ultra 120 for cooling.
 
I just bought the friggin' processor. Should be Conroe. I'm being lied too otherwise. :)

I used both Tat and Core temp. Tat says Pent M, don't know why though. :)

Temps-1.jpg



I'm using a Thermalright Ultra 120 for cooling.

don't use orthos....
use TAT and coretemp together. use TAT's stress by starting the stress test on TAT... then see the temps
 
It's quite possible that you have hit the practical overclock limit, there are plenty of e6600 that won't do 400x9, you just don't hear people bragging about them. That CPU will likely go higher with more voltage, but the diminshing returns and rapidly increasing heat load will make it impractical. My present stable OC on this chip is right at 400x9, and that's on high end watercooling. In fact, this CPU maxed out at 380x9 on two other motherboards, only the BX2 would take it higher. I can scale higher than this but I don't feel the big volt increases required are worth a speed bump that isn't noticable in day to day use.

TAT says its a pentium M because it is a utility Intel created for manufacturers to test the thermals on laptops. It wasn't designed for desktop processors, so it is reading wrong. TAT is good for checking your temps and cooling, but it isn't an effective stability test, it doesn't check for errors it just creates a lot of heat.

If it's a 6600 it's a conroe, there is no such thing as an allendale 6600. 4300-6300-6400 are allendale, 6600-6700-6800 are conroe. 4Mb L2 cache = conroe, 2Mb L2 cache = allendale
 
I don't think that will work based on the fact I used an after market cooler.

Or could they tell? How am I supposed to justify the RMA anyway?
 
I don't think that will work based on the fact I used an after market cooler.

Or could they tell? How am I supposed to justify the RMA anyway?

gREEDY! that's all.

ur on air. that's about right for an OC. btw did you try the thing i listed above?
 
If it's a 6600 it's a conroe, there is no such thing as an allendale 6600. 4300-6300-6400 are allendale, 6600-6700-6800 are conroe. 4Mb L2 cache = conroe, 2Mb L2 cache = allendale

All the e6xxx processors are conroe cores. The 6300 and 6400 are conroes too, they just have 2mb of the 4mb cache disabled. The e4300 is the only allendale core currently on the market, it was designed with only 2mb of cache.
 
A few of my friends hit 3.8 on air but were running pretty hot.

I'm at work and won't be able to do any OCing til Sunday night probably. I have to reinstall windows and won't see my computer til tomorrow. So I'll get back on and see what happens when I do that. :)
 
All the e6xxx processors are conroe cores. The 6300 and 6400 are conroes too, they just have 2mb of the 4mb cache disabled. The e4300 is the only allendale core currently on the market, it was designed with only 2mb of cache.

well my e6300 is allendale i think since coretemp registers it as 19C idle! tha'ts why i was asking if taht's a prob with e6600
 
Good temps hmm. I think thats probally it for the cpu but ......

Have you run memtest to validate its not your memory ?
( I really doubt it but you need to make sure)

drop mulitplier down a notch and try 400 x 8 at 5 5 5 15 and also Auto.

(my machine will determine some strange timings on Auto that will give me some more FSB at the "edge", things like 5 7 7 18 etc. it works /shrug. )

I beleive the stock voltage is 2.2 , 2.25 is not much of a bump. I would consider 2.3 if case airflow is good and use the "finger temp probe" to check temps as memtest runs a pass. I am not big on pouring on the volts but 2.3 is less than 10% over spec and if those are micron D9s under the heat spreaders they will love it.

Note: I realize at 400 that memory is at spec and shouldnt even be breaking a sweat, but you need to be sure.
 
3.8ghz on air? i get 3.4 on water. i might try new thermal compound as i'm getting 48 degrees @ 3.4ghz. i could go further but it isnt worth it for the temps.
 
Just RMA it, you should get way higher. I would be pissed.

Holy cow thats one of the lamest posts ive seen in awhile. RMA a cpu because it doesnt OC to what you want? Christ, no wonder prices suck.
 
Good temps hmm. I think thats probally it for the cpu but ......

Have you run memtest to validate its not your memory ?
( I really doubt it but you need to make sure)

drop mulitplier down a notch and try 400 x 8 at 5 5 5 15 and also Auto.

(my machine will determine some strange timings on Auto that will give me some more FSB at the "edge", things like 5 7 7 18 etc. it works /shrug. )

I beleive the stock voltage is 2.2 , 2.25 is not much of a bump. I would consider 2.3 if case airflow is good and use the "finger temp probe" to check temps as memtest runs a pass. I am not big on pouring on the volts but 2.3 is less than 10% over spec and if those are micron D9s under the heat spreaders they will love it.

Note: I realize at 400 that memory is at spec and shouldnt even be breaking a sweat, but you need to be sure.

Cool. I'll try that.

Yes, my ram is d9. My motherboard however has 2.15 and 2.25 then 3.0. 2.2 Isn't available so I just keep it at 2.25.

I ran memtest when I originally built my machine and with stock settings memtest failed. However I tightened the timings from 555 to 444(which it's supposed to be) and it's been fine ran memtest all day and night.

I haven't done it with a faster FSB though, or higher voltages. It didn't like it at 2.25 @ 5-5-5-15 with a FSB of 266.

My case has plenty of airflow for cooling, look at the fan pulling heat from the ram. :) So much cold air is being pulled into that case the heatsink doesn't notice. :p

http://i179.photobucket.com/albums/w313/Rsgunter/HeatsinkFront.jpg

Also I'll mention that I did tried dropping the multiplier and ran 400+ x 8 with no issues.

Would it be safe to say I would be better off keeping my ram at 4-4-4 and my CPU and 3.45 rather than 3.55 @ 5-5-5?
 
Cool. I'll try that.

Yes, my ram is d9. My motherboard however has 2.15 and 2.25 then 3.0. 2.2 Isn't available so I just keep it at 2.25.

I ran memtest when I originally built my machine and with stock settings memtest failed. However I tightened the timings from 555 to 444(which it's supposed to be) and it's been fine ran memtest all day and night.

I haven't done it with a faster FSB though, or higher voltages. It didn't like it at 2.25 @ 5-5-5-15 with a FSB of 266.

My case has plenty of airflow for cooling, look at the fan pulling heat from the ram. :) So much cold air is being pulled into that case the heatsink doesn't notice. :p

http://i179.photobucket.com/albums/w313/Rsgunter/HeatsinkFront.jpg

Also I'll mention that I did tried dropping the multiplier and ran 400+ x 8 with no issues.

Would it be safe to say I would be better off keeping my ram at 4-4-4 and my CPU and 3.45 rather than 3.55 @ 5-5-5?

K, had to ask, agree 3.0 is too much so 2.25 it is.

However I tightened the timings from 555 to 444(which it's supposed to be) and it's been fine ran memtest all day and night.
K, really odd it would not run at 5 5 5 but doesnt matter as you have proved 400 at 444 is good, which it should be + some.

You would have to benchmark it but c2d systems are pretty insensitve to memory timings, typically you get the best results with the cpu as fast as possible and let memory timings fall where necessary. So 3.55 @ 5 5 5 will probally bench faster.

But its strange, we know your memory is good at 400 at 4 4 4 so you should be able to get 9 x 400. if the cpu can do it.

So I am at a loss, its either as you think, thats it for the cpu, or more likely its a combination of timings in the cpu, motherboard and memory that is causing the instability.

all you can really do is give it some more voltage, 1.5 is Vmax for the chip (some people mistakenly quote 1.55 but thats for Vss a signal voltage) so I would give it a try at 1.45 just to see, short run wont hurt and its up to you if it works and you wish to keep it there. I personally dont like over 1.4 V but I am very conservate and some people have them running at almost 1.6V. I just dont think its worth it in terms of reduced life, temps are not everything and electrical stress on the semi-conductor junctions due to very high voltages is something we have no way of measuring.
 
OP, You have some really good temps there where you are running. On my 6600 I had to up the voltage a bit to get past 3.5 Orthos stable. To hit 3.6, I needed to up the MCH voltage to 1.6v and up the FSB voltage some too. Not too sure if this would apply to your 965 chipset, it did on my chipset though.
 
how are you getting so far on air? i'd be very pleased! myn hits 48 degrees on water @ 3.4ghz...
 
I have a similar set up...hit a wall at 400x9. Tried 401, 405 etc and went up to 1.625v couldn't stabilize on water even. Ended up settleing for 3.56ghz nice and stable @ 1.55v. It makes me laugh when people aren't happy with thier 1ghz+ overclock. Some people just get better cpus, and on this forum those are gernerally the people you hear from. Sounds to me like you've tried everything I have let me know if you have any success.
 
advice: be happy, you already have a great overclock

(Anything above 3.3Ghz is good since that seems to be about the average lately. above average = good)

the only thing I would have said to try is 401 since a new strap kicks in there, but seems as though you've already tried that.
 
I am stable at 3.7GHz on air. 411x9 (1645FSB) 1.3625 VCore - Zalman 9700

No Issues so far, I might even be able to go higher, I just havent tried yet.

Edit: I dont know if it matters, But I have a week 30a.
 
what temps are you getting ^^. i think i need new thermal paste judging by this if i get 48 degrees on water at 3.4ghz...
 
My e6600 is stuck at 395 x 9. I can't get stable past that. Trying to figure out if I've hit my CPU limit. I've tried my ram at 4-4-4-12 and 5-5-5-15 at 2.25 and can't get stable.

Asus P5B Deluxe (newest bios)
E6600 -- Thermalright Ultra 120 @ 1.425
Crucial Ballistix ddr2800 @ 2.25

Temps under load running Orthos are around 45-48c.

CPU limit or am I missing something?

you have PECI enabled? open up ASUS PROBE and see what your 1.425 vdroops to...
 
I am stable at 3.7GHz on air. 411x9 (1645FSB) 1.3625 VCore - Zalman 9700

No Issues so far, I might even be able to go higher, I just havent tried yet.

Edit: I dont know if it matters, But I have a week 30a.

Thats amazing 3.7!!! I bet 6800 can get close to 4Ghz. Might reconsider about c2d, qx6700 couldnt go pass 3.55ghz.
If I get c2d 6800 pc now, will it last me at least 1-2 years?
 
Thats amazing 3.7!!! I bet 6800 can get close to 4Ghz. Might reconsider about c2d, qx6700 couldnt go pass 3.55ghz.
If I get c2d 6800 pc now, will it last me at least 1-2 years?

Yeah I deffinalty think if you get a C2D E6600 even at default 2.4GHz it will last you at least a full year. Most software - Espically games really cant take advantage of dual core yet. While more and more software is being designed for it, Im sure a good dual core setup will last you a while.

E6600
2GB Ram
Any Direct X 10 card, even the 320GTS

That setup will last you into 08 for sure.
 
thats what i have... only i got another gfx slot for another 8800gtx, room for another 2gb ram and savin for quad core.
 
what temps are you getting ^^. i think i need new thermal paste judging by this if i get 48 degrees on water at 3.4ghz...

E6600 @ 3.7GHz 1.3625v
44 Idle - 54 Full Load. Good enough for me. It dosent throttle, and its not so hot its dying. For the speed, I wont complain.
 
Yeah I deffinalty think if you get a C2D E6600 even at default 2.4GHz it will last you at least a full year. Most software - Espically games really cant take advantage of dual core yet. While more and more software is being designed for it, Im sure a good dual core setup will last you a while.

E6600
2GB Ram
Any Direct X 10 card, even the 320GTS

That setup will last you into 08 for sure.

Thanks! decisions, deciosions...:p
Apparently intels 4x4 is due to in aprill, <2 months aint that long 2 wait, + by then prices r going t drop 4 c2d's.
Comeon Intel - show us da beast!!!
 
what temps are you getting ^^. i think i need new thermal paste judging by this if i get 48 degrees on water at 3.4ghz...

I think you should remount your block or something, or fix your WCing. Cause 48C even at load at 3.4ghz is wayy too much. Unless you have the auto OC on and the voltage is increasing by itself, make sure you disable this feature and do the voltage adding by yourself.
Remounting your block and making sure its secure will prolly drop your temps a bunch. Cause i did a mod on my sycthe ninja w/ a DD block mounting kit, and i had to screw those screws tight to get my full cooling potential.

Thermal paste shouldnt actually really make your temps drop too much but uhh if you wanna see some good reviews on thermalpaste... they did a review on XS


Oh.... what Intel 4x4?!?!
Its clearly AMD 4x4... Intel has its QC chips... just a little... note...
 
Thanks! decisions, deciosions...:p
Apparently intels 4x4 is due to in aprill, <2 months aint that long 2 wait, + by then prices r going t drop 4 c2d's.
Comeon Intel - show us da beast!!!

Im going to be honest with you. I know people will agree and I might get slammed.

But - I know 4x4 isnt out yet. But clearly the superior technology is a Core 2 Quad setup vice an AMD 4x4 Setup.

Not only that, but the AMD 4x4 setup will be much more expensive.
 
Back
Top