SATA II HDD and a headache

Joined
Jun 11, 2008
Messages
5
Motherboard: Gigabyte 7VM400AM-RZ
BIOS: Updated
Processor: AMD Athlon XP, 1666 MHz (16.5 x 101) 2000+
SATA II HDD: WD Caviar Green Model: WD5000AACS

I have tried everything, and so help me I do mean everything, to get the SATA HDD working.
BIOS is set to IDE for SATA and all the appropriate settings have been tried, as well as a manual install, with Cylinder at 1023, Head at 16, and Sector at 63.
The F6 and installing of Windows XP (SP 3) has been attempted.
Even putting jumpers on the pins, even though it shouldn't make any difference because of the Master/Slave default of SATA.
Two different SATA cables.
With and without IDE HDD.
RAM swapped.
CMOS battery taken out for over 1/2 hour.
WD Diagnostic LifeGuard.
Read, re-read, and read again, the Motherboard manual, (and I know that SATA 1.5 is recommended by Motherboard manufacturer), and pretty much every single site that mentions a similar problem, without a solution so far.
The correct SATA/RAID drivers don't install properly, with the 'road sign' error of '!' next to it permanently. (also have same happen as a similar post, with the SATA/RAID driver being okay when the SATA hdd wasn't connected), and the message "this device cannot start [Code 10].
I'm pretty much at the end of my tether, and realise I'm going to have to go another way around this to get the SATA hdd working. Birthday is coming up, and I will be able to afford one of the three 'possible' solutions:
1. CPU Upgrade
2. PCI SATA Adapter Card
3. Second SATA HDD and run RAID (I'm leaning away from this because it's not being installed/detected though)

I need some suggestions of which would be the most likely to pick up the SATA hdd with as many opinions as possible. I've pretty much reached the conclusion it is just not going to work on this setup, and although I'd like to update the entire system, that just isn't going to happen now.

Thanks in advance.
Victoria
 
Whats your operating system? and whats the driver release version?

I suggest a visit to this site and get the latest release for your OS

hope it helps :D
 
Operating System: XP (SP3)
Drivers: Been there done that as far as the drivers go. 5.70 is the latest release drivers, 4.06 or 7 (i 'think') were what came with the motherboard. They were tried as well, both did the same thing.
Victoria
 
Those "jumpers" aren't related to the master/slave configuration. The jumper on the back of all SATA drives is meant for backwards compatibility since some motherboards do not support SATA II drives. Like your Gigabyte motherboard for example. With the jumper on, the drive acts and looks like a SATA I drive to the drive controller. With the jumper off, the drive acts and performs like a SATA II drive.

Have you tried using that drive in another system?

#2 would be the cheapest option since PCI SATA controller cards around $15 to $25 these days.
 
My last motherboard died on me, to the point that it wouldn't post with the barest of essentials on it. First the AGP card died, then the IDE hdd wouldn't boot, then the fan clicked louder than Jiminy Cricket on a cold night, etc etc. I had access to the SATA drive, got to Initialize, Partition and format it. That motherboard was previously set up for RAID and ran 4 hdd's though The SATA hard drive has been back to where I bought it, and they tested it and said it's working fine. I also got a new cable when they sent it back 'in case' that was the problem. There really isn't anything I've come across that I haven't tried.
This motherboard has become pretty much a 'quick' replacement until I can get batter, and missing the 500GB's is holding up on getting stuff sorted around here, that has a time constraint to a point, so the best option is to get it, at the very least working.

Victoria
 
Also tried the jumper on all pins at different times, and always rebooted, tried a few times with different settings in BIOS, manual, LBA, the F6 option to install XP etc.

Victoria
 
*while she mumbles and calls her computer every single name under the sun, thought she'd go back and just 'try' the jumper on 5-6 again. Nothing showed up, so reinstalled the earlier driver and BINGO, it's showing up with the partitions in place*

I'm now going to go and sit in a corner, twiddle my thumbs and wonder if anybody else has been made to look a fool by their computer, knowing that there's thousands who qualify!!

dhc014 - Thankyou for suggesting it.

Everyone else who replied, thanks!!
 
Back
Top