Possible to change processors?? Doesn't AS5 glue down the CPU??

Viperjts10

Weaksauce
Joined
Jul 19, 2007
Messages
123
If arctic silver 5 is used to glue down the processors, is it still possible to change them in the future? I have never really built a computer yet, but I'm in the process of building my first one. I have an old computer (about 2 years old) and it has a pentium 4 on it. It isn't bad yet and still runs really smooth, but let's say in another 2 years, would it be possible tto change the processor? Do I just pry it off the motherboard, or how does that work.
 
:)

Arctic Silver isn't a glue. It's a thermal compound made up of polysynthetic zinc, aluminum, and some silver. The purpose of this isn't to glue the heatsink to the processor, it's to allow the heat to transfer better.

The bottom of your heatsink, and the top of the CPU is not atomically smooth where they meet. If you looked at the two under a microscope, you could see millions of little craters. These minuscule gaps trap air in between the two, which makes it harder for heat to transfer efficiently. Thus they invented a thermal compound which is made up of high density liquid metal to fill those little imperfections, allowing your heatsink to function better.

Since thermal compound isn't glue, removing it is very easy. Once you unlatch the heatsink, it doesn't require any additional force to pull the two apart. Just make sure that once you're ready to either put that heatsink back on, or a different one, that you clean them. Put some Isopropyl Alcohol (which you can easily get at any drug store), on a dry, lint free cloth, and carefully use it to remove all of the compound from them, replacing it with some fresh Arctic Silver 5 when you're ready to put it all back together.


Edit: Since this is your first time building a computer, I thought this was worth mentioning. When you're handling the CPU, you have to be extremely gentle with it. Under no circumstances are you ever to touch the bottom of it. If you damage even a single pin or pad on there, you can irreparably destroy the processor. The same goes for the socket on the motherboard. Always hold the processor by the edges with the tips of your fingers, and never apply any unnecessary force when inserting it into the socket. If it feels like the processor doesn't want to go into the socket on the first try, then stop and make sure you're inserting it correctly.

Also, if you don't have an anti-static wristband available when you put it together, try to ground yourself by touching solid metal (such as the case on your power supply) as often as possible. Static electricity can easily kill most computer components.
 
If arctic silver 5 is used to glue down the processors, is it still possible to change them in the future? I have never really built a computer yet, but I'm in the process of building my first one. I have an old computer (about 2 years old) and it has a pentium 4 on it. It isn't bad yet and still runs really smooth, but let's say in another 2 years, would it be possible tto change the processor? Do I just pry it off the motherboard, or how does that work.

you use the as5 between the heatsink and cpu, it does not glue it on, you should have no problem removing it in the future.
 
If arctic silver 5 is used to glue down the processors,

Not quite right, it is a thermal paste, it is not a glue. It is just there to help transfer heat not to hold anything on. The heatsink will come right off if using AS-5.

Now Arctic Silver does make something called Arctic Epoxy, comes in two tubes and has to be mixed, that is used to permanently attach heat sinks to ram chips etc. but it is not to be used on CPUs (in general).
 
:)

Arctic Silver isn't a glue. It's a thermal compound made up of polysynthetic zinc, aluminum, and some silver. The purpose of this isn't to glue the heatsink to the processor, it's to allow the heat to transfer better.

The bottom of your heatsink, and the top of the CPU is not atomically smooth where they meet. If you looked at the two under a microscope, you could see millions of little craters. These miniscule gaps trap air in between the two, which makes it harder for heat to transfer efficiently. Thus they invented a thermal compound which is made up of high density liquid metal to fill those little imperfections, allowing your heatsink to function better.

Ok thanks, so then is removing the heatsink and processor is as simple as unscrewing the heatsink and then just pulling out the cpu from the motherboard?

I have my motherboard and cpu cooler, but I have not opened them because I'm waiting to buy my final piece to my build which is the processor.
 
AS5 is not glue. You can easily lift a heat sink from a CPU years after applying Arctic Silver. It cleans up easily with a few Q-Tips dipped in 99% isopropyl alcohol.

Oh, and the AS5 is to provide a means of heat transfer between the CPU and the heatsink on top of it ... it is *not* to be used between the CPU and motherboard!
 
Ok thanks, so then is removing the heatsink and processor is as simple as unscrewing the heatsink and then just pulling out the cpu from the motherboard?

I have my motherboard and cpu cooler, but I have not opened them because I'm waiting to buy my final piece to my build which is the processor.

Yes, it's fairly easy to remove. If you're still using the stock cooler, then all you have to do to remove it is twist the four little pillars to unlock them, then pull up on each one to pop them out of the motherboard. This is easier if you place your hand directly on top of the cooler while you pull the pillars out, so long as you don't put any extra pressure on it. Once all four pillars have been popped out of the motherboard, slowly lift up on it, and it'll come right off.

To remove the CPU, find the little latch running along the side of the socket. This looks like a metal rod that ends in a long U-Shaped curve. Lightly push down on the curved piece until it clears the little tab holding it in place, swing the metal rod out so that it's free from the tab, and then lift it all the way up. This will unlock the plate on top of the CPU that's holding it in place. Lift the plate up and your CPU can now easily be raised from the socket.

Also, be sure to read the edit in my first post.
 
Ok thanks for all the help. I'll refer back to this when I go to build the computer. I need my check to come in the mail so I can buy my Cpu at frys!!
 
Edit: Since this is your first time building a computer, I thought this was worth mentioning. When you're handling the CPU, you have to be extremely gentle with it. Under no circumstances are you ever to touch the bottom of it. If you damage even a single pin or pad on there, you can irreparably destroy the processor. The same goes for the socket on the motherboard. Always hold the processor by the edges with the tips of your fingers, and never apply any unnecessary force when inserting it into the socket. If it feels like the processor doesn't want to go into the socket on the first try, then stop and make sure you're inserting it correctly.

also, dont set your processor down on the carpet next to your computer chair, then accidentally run over it with the wheel of the chair.

-fluxion, who was lucky enough to to still have a working proc once all the pins were bent back into place
 
Back
Top