I've spent a good amount of time researchng a fix as to not waste everyone's time here, but my frustrations have hit a tipping point. System details are at the bottom..
I first installed the drive as a secondary drive for prepping. Using OCZ toolbox, I updated to firmware 1.23. I then did a Secure Erase. My system had no difficulty recognizing the drive either before or after these steps. It is purring along fine right now as an application drive.
I bought the drive to replace my aging Maxtor Maxline III as a boot drive; it's the loudest thing in my system by far. After confirming that the drive worked and setting it up as the only SATA drive attached to my system, I made sure to clear the CMOS and set it as the first drive in the BIOS in both locations. I changed the RAID setting to AHCI and dropped the appropriate drivers on a second thumb drive just in case. Here's where things get funky.
The PC makes it past the POST and begins booting from my Windows 7 USBdrive. When it started to load the OS, I noticed that the white bar is filling up really slowly - much more so than any hdd install had gone. It finally gets to the Upgrade/Complete/Other page and I choose to install a new OS. The drive appears in the list - no issue there. Any attempt to do anything hits a brick wall. Going forward, I get the message that the computer cannot do anything with the drive (something about partitions, etc - things I'd taken care of earlier, I thought). I try loading the AHCI drivers from my driver USB; the drivers load right away, but I still can't move forward with the install.
Long story short, despite following instructions found through Google and at the manufacturer's site I just can't seem to install Windows 7 to this drive. it's working great as an app drive, but that's not why I bought it. I really don't want to send it back but I fear I may have to. I'm willing to give any suggestion a go that the gurus here recommend.
Thanks for your help.
System:
Gigabyte EP35-DS3P F5; Intel Q9300 @ Stock
8GB (4x2) Corsair DDR800, EVGA GTX460 OC 1GB
Corsair HX620W PSU, Maxtor Maxline III 250GB HDD
I first installed the drive as a secondary drive for prepping. Using OCZ toolbox, I updated to firmware 1.23. I then did a Secure Erase. My system had no difficulty recognizing the drive either before or after these steps. It is purring along fine right now as an application drive.
I bought the drive to replace my aging Maxtor Maxline III as a boot drive; it's the loudest thing in my system by far. After confirming that the drive worked and setting it up as the only SATA drive attached to my system, I made sure to clear the CMOS and set it as the first drive in the BIOS in both locations. I changed the RAID setting to AHCI and dropped the appropriate drivers on a second thumb drive just in case. Here's where things get funky.
The PC makes it past the POST and begins booting from my Windows 7 USBdrive. When it started to load the OS, I noticed that the white bar is filling up really slowly - much more so than any hdd install had gone. It finally gets to the Upgrade/Complete/Other page and I choose to install a new OS. The drive appears in the list - no issue there. Any attempt to do anything hits a brick wall. Going forward, I get the message that the computer cannot do anything with the drive (something about partitions, etc - things I'd taken care of earlier, I thought). I try loading the AHCI drivers from my driver USB; the drivers load right away, but I still can't move forward with the install.
Long story short, despite following instructions found through Google and at the manufacturer's site I just can't seem to install Windows 7 to this drive. it's working great as an app drive, but that's not why I bought it. I really don't want to send it back but I fear I may have to. I'm willing to give any suggestion a go that the gurus here recommend.
Thanks for your help.
System:
Gigabyte EP35-DS3P F5; Intel Q9300 @ Stock
8GB (4x2) Corsair DDR800, EVGA GTX460 OC 1GB
Corsair HX620W PSU, Maxtor Maxline III 250GB HDD