Nforce4 Ultra ethernet question

steven_d02

n00b
Joined
Feb 15, 2005
Messages
51
Recently I bought a chaintech Nforce4 ultra s939 mb, recently it has started just randomly turning off the network card. I've made sure the auto power saver thing is urned off, I installed the most recent Nforce4 stand alone kit from nvidia. Is there maybe a setting or something that I am missing?
 
I've got a Biostar nForce4 based board running as a file server. Talk about a NIC that HAS TO work. It's been through three OS's and I've never had that problem, nor have I had to do anything "special."

It could be a bad board. My wife has a VIA based board that does the same thing. Just drops the network connection. Cards still there. Network connection enabled. Says that there's a cable plugged in, but no connectivity.

She's gone through two OS's. Same problem. Even disabled the power manage. for the device. No dice.

Installed a $9 Realtek NIC and she's back online w/ no issues. :(
 
if thats all it takes to fix it, I think I have an extra NIC card somewhere. Anyone else have any suggestions??
 
I am not a fan of Biostar, ECS, chaintech... they are all low low end motherboards.

Every NForce 4 onboard NIC I have seen works perfectly, but they are on high end mobos, like ASUS /Abit/ MSI.

I would update your bios to the latest version and get the newest drivers and see if that works for you.
 
I've downloaded the latest BIOS from chaintech and the news Nforce4 stand alone kit from Nvidia. I've even already reloaded the whole computer just to make sure something hadn't gotten into my system to cause the problem and its still doing it.
 
USMC2Hard4U said:
I am not a fan of Biostar, ECS, chaintech... they are all low low end motherboards.

Every NForce 4 onboard NIC I have seen works perfectly, but they are on high end mobos, like ASUS /Abit/ MSI.

No offense, but telling people they have a low-end motherboard and that they should expect problems like this doesn't help solve the problem.

When you clear the CMOS does it still give you problems?
 
kirbyrj said:
No offense, but telling people they have a low-end motherboard and that they should expect problems like this doesn't help solve the problem.

When you clear the CMOS does it still give you problems?
I am here to give opinions. I am not here to be light and happy. I spoke the truth.

Anyway, I gave advice. Flashing to the newest bios, and updating to new drivers sounds like that might fix a problem.
 
USMC2Hard4U said:
I am here to give opinions. I am not here to be light and happy. I spoke the truth.

Give opinions or speak truth? ;)

If the truth as you know it is that MSI boards are infallible and Biostar and Chaintech boards are prone to fail, that's your opinion and you're entitled to it.

No doubt, MSI boards are higher end than brands like Biostar and Chaintech, but my "truth" is I've deployed almost 100 Biostar based workstations over the last year and none have had a failure, but when I switched over to ASI as a supplier and got a run of 10 MSI motherboards because they couldn't get me Biostar, I ended up with five motherboards with five different problems.

Sorry if I don't sound light and happy, but we have to deploy someone out of our Tampa office to Sacramento, CA because an MSI based workstation there has a NIC that randomly drops out and the only remedy is to cold boot. Naturally, power cycling the PC is not a suitable solution in the customer's eyes... especially since they're trying to run IP Softphones off of it! :(

Unfortunately, no motherboard manufacturer is infallible.

Don't get me started with the 20% RMA rate I've had with Abit motherboards and the components on Asus boards that spontaneously catch fire and when you go to RMA them to Asus they say they won't because the part was "obviously overclocked," but if you do manage to get an RMA from them, they just send you someone else's untested, unrepaired RMA. :rolleyes:
 
steven_d02 said:
to clear the CMOS all I have to do is take out the battery for a few seconds right?

There SHOULD BE a jumper. Look for something labeled "JCMOS" or "CMOS1" or something like that near the battery.

But if all else fails... Yes.. If you pull the battery, you should be able to clear out the BIOS. Just leave it out for a few seconds.

And USMC2: Just so you know, I'm not saying I'm right and you're wrong. I read my post and it may sound like it came off that way, but I'm well aware that you may have had a bad experience with Biostar or Chaintech in the past. It's just that the OP said he had a Chaintech and it wasn't working and then I said I had a Biostar and it worked fine and then you came in with the idea that they're both crap boards and that it's probably a miracle mine works at all (not quite, but the tone implied as much.)

Regardless of our different opinions: Keep up the good work!
 
thanks I'll look at the documentation that came with the board to find the location of those jumpers. As far as the argument about the quality of mother boards out there... your right I probably could've gottne a better board but this was a budget system I built for my brother and he has absolutly no intention of over clocking it at all so I found a chipset that was of good quality for the CPU that he wanted which is an Athalon64. not that your opnions would make me regret the decision, everyone has an opinion. Thanks for the all the help you guys have given me.
 
Back
Top