praetorian
Weaksauce
- Joined
- Sep 9, 2003
- Messages
- 84
Hey guys,
I'm planning to water cool my entire system and move away from air cooling completely in my White Raven RV02-E. However, since I'm a n00b to this, I wanted to check a spec check on the following components to see if I've got this right as well as the number of connectors and also not mixed components.
1x Koolance RP-452X2 Dual 5.25in Reservoir for 1-2 PMP-450/S Pumps, Rev.2.0 + 2x PMP-450 Pumps + 4 Single (1/4in x 3/8in)
1x Magicool Triple 180mm Radiator G1/4"
1x EK Water Blocks EK-Supremacy EVO - Nickel
2x EK Water Blocks EK-FC R9-290X - Nickel CSQ (REV 2.0)
1x EK Water Blocks HD Tube 10/12mm 3-Slot (2 pcs)
2x EK Water Blocks EK-FC R9-290X Backplate - Black
1x QD2 Female Quick Disconnect No-Spill Coupling, Compression for 06mm x 10mm (1/4in x 3/8in)
1x QD2 Male Quick Disconnect No-Spill Coupling, Compression for 06mm x 10mm (1/4in x 3/8in)
10xFitting Single, *Black* Compression for 06mm x 10mm (1/4in x 3/8in), G 1/4 BSPP
2x Fitting Single, *Black* Swivel Angled for 06mm x 10mm (1/4in x 3/8in), G 1/4 BSPP
3x Fitting Single, *Black* Swiveling 45-Degree, G 1/4 BSPP
4x Koolance LIQ-702 Liquid Coolant Bottle, High-Performance, 700mL (UV Yellow)
6x Koolance Tubing, Clear UV-Reactive PVC, 06mm x 10mm (1/4in x 3/8in)
I'm going to be drilling out the rivets on the 3.5" hotswap bay to make room for the Magicool radiator and I've also gone for a bay mounted Koolance dual pump solution in serial to give me as much flow rate as possible.
I'll be hooking in the two GPUs, rad, CPU + res so I believe I'll need 8 connectors (but gone for 10 anyway) etc etc.
Any input would be extremely helpful as its not something that I've done before. The tubing is also an area where I'm not exactly sure as I think the sizes that I've chosen will allow a good, clean flow without any bottle necks but also long lasting.
Cheers all
I'm planning to water cool my entire system and move away from air cooling completely in my White Raven RV02-E. However, since I'm a n00b to this, I wanted to check a spec check on the following components to see if I've got this right as well as the number of connectors and also not mixed components.
1x Koolance RP-452X2 Dual 5.25in Reservoir for 1-2 PMP-450/S Pumps, Rev.2.0 + 2x PMP-450 Pumps + 4 Single (1/4in x 3/8in)
1x Magicool Triple 180mm Radiator G1/4"
1x EK Water Blocks EK-Supremacy EVO - Nickel
2x EK Water Blocks EK-FC R9-290X - Nickel CSQ (REV 2.0)
1x EK Water Blocks HD Tube 10/12mm 3-Slot (2 pcs)
2x EK Water Blocks EK-FC R9-290X Backplate - Black
1x QD2 Female Quick Disconnect No-Spill Coupling, Compression for 06mm x 10mm (1/4in x 3/8in)
1x QD2 Male Quick Disconnect No-Spill Coupling, Compression for 06mm x 10mm (1/4in x 3/8in)
10xFitting Single, *Black* Compression for 06mm x 10mm (1/4in x 3/8in), G 1/4 BSPP
2x Fitting Single, *Black* Swivel Angled for 06mm x 10mm (1/4in x 3/8in), G 1/4 BSPP
3x Fitting Single, *Black* Swiveling 45-Degree, G 1/4 BSPP
4x Koolance LIQ-702 Liquid Coolant Bottle, High-Performance, 700mL (UV Yellow)
6x Koolance Tubing, Clear UV-Reactive PVC, 06mm x 10mm (1/4in x 3/8in)
I'm going to be drilling out the rivets on the 3.5" hotswap bay to make room for the Magicool radiator and I've also gone for a bay mounted Koolance dual pump solution in serial to give me as much flow rate as possible.
I'll be hooking in the two GPUs, rad, CPU + res so I believe I'll need 8 connectors (but gone for 10 anyway) etc etc.
Any input would be extremely helpful as its not something that I've done before. The tubing is also an area where I'm not exactly sure as I think the sizes that I've chosen will allow a good, clean flow without any bottle necks but also long lasting.
Cheers all