new rig, some issues

mnewxcv

[H]F Junkie
2FA
Joined
Mar 4, 2007
Messages
9,301
specs:

antec nsk2400
xclio 500w goodpower
4000+ brisbane
2 x 1gb patriot 4-4-4-12 ddr2 800
foxconn A690GM2MA-8KRS2H
2 x 36gig raptors

following issues:

#1. cant figure out how to do raid 0. couldnt find anything in the bios, and when i loaded the raid drivers in the windows install it just asked which i wanted to install windows on. I have never done raid so i might be forgetting something.

#2. HDD light is always on. i turn on the comp and its off, after post when it begins to load windows it looks like it should, starting and flickering like a hdd in use, but as soon as the splash screen comes on it stays on constantly.

#3. memory speed. in the bios there are the following settings for ram speed: 200, 266, 333, 400. I dont know which i should be using, default was 200, should it be 800? in the cpuz memory tab it shows 367mhz for ram speed with the bus at 210mhz and mem at a cpu/6 divider.

any help appreciated.
 
specs:

antec nsk2400
xclio 500w goodpower
4000+ brisbane
2 x 1gb patriot 4-4-4-12 ddr2 800
foxconn A690GM2MA-8KRS2H
2 x 36gig raptors

following issues:

#1. cant figure out how to do raid 0. couldnt find anything in the bios, and when i loaded the raid drivers in the windows install it just asked which i wanted to install windows on. I have never done raid so i might be forgetting something.

#2. HDD light is always on. i turn on the comp and its off, after post when it begins to load windows it looks like it should, starting and flickering like a hdd in use, but as soon as the splash screen comes on it stays on constantly.

#3. memory speed. in the bios there are the following settings for ram speed: 200, 266, 333, 400. I dont know which i should be using, default was 200, should it be 800? in the cpuz memory tab it shows 367mhz for ram speed with the bus at 210mhz and mem at a cpu/6 divider.

any help appreciated.


1. I've never used raid so can't help there, sorry

2. You might have the HDD activity light jumper from your mobo to the case on the wrong way (upside down), so check this and se if flipping it resolves your issue.

3. DDR 2 = DOUBLE DATA RATE, so your settings should be 400 (2x400 = 800MHz).
 
bump help with raid

You get a free bump here with the rider that you don't want to bump too often, its frowned upon.

I'd say about once per day is the norm, that's just advice the mods might have a different opinion.

Don't fret if no-one answers in an hour, I realise you might be desperate to get on but more often than not if someone can help they will.
 
thanks for the tip.

at stock i was getting like 44s in superpi 1m. oced to 228 x 10.5 aka 2390-2400mhz i get 36s. are these good times?
 
1) RAID0 is easy...

a) Go into your BIOS and enable RAID
b) go into the RAID Config utility (watch for what keys to press to get into it during POST)
c) setup the drives for RAID0
d) assuming you're using XP, press F6 at beginning of installation
e) create a floppy disk with the SATA RAID drivers on it if one wasn't provided with the mobo
f) stick floppy disk in when XP installation asks for it
g) complete XP installation

2) The polarity of your HDD LED light is reversed, so flip it (as someone mentioned earlier)

3) Yah, set it to 400. Though, you're using a brisbane, which has half-step dividers, so you won't get DDR2-800 exactly.
 
ok I got it all figured out now. memory must have set itself higher anyways because setting it to 400 made no changes in cpuz readings. As for the HDD light, reversing it didnt work at all, but setting raid in the bios instead of native IDE and now it works perfect. raid0 up and running, was a little cautious cuz i didnt know what delete, define, etc and didnt have a clue which to do. thanks a lot for the help guys!
 
Back
Top