new computer - no POST, no case speaker, no CPU fan - help!

Eruditass

Gawd
Joined
Jul 7, 2002
Messages
692
So I just put together a computer for my brother's birthday and it isn't turning on. specs:

Q6600
Xigmatek HDT-S1283 w/ mounting bracket
Gigabyte GA-EP45-UD3R
OCZ 2x1 SLI
9600 GSO
OCZ silent
antec 300

I've noticed the CPU phase lights are all on, the fans turn on, but the cpu fan spins very very very slightly and stops- is this a motherboard problem? I've reset the CMOS.

the worst part about this problem is the antec 300 has no case speaker! how can i determine what is wrong?

I've unplugged everything and tried, no luck, but I haven't tried reseating the CPU, as that was quite annoying. Since the CPU fan barely turns maybe 1 degree, it has to be a power supply or motherboard problem right?
 
- Did you plug in the CPU fan?
- Did you reassemble the PC outside of the case?
- What PSU are you using?
 
OCZ silentxstream 500W

i noticed now that there is a high pitched whining with just the psu, cpu, and motherboard. im taking it out of the case to figure out what it is.

yes the cpufan is plugged in
 
swap out the PSU first, it doesn't have to be beefy just to test it out, a 300w should be good enough to just test it, or even less. if its it still has the problem with a different PSU, then its probably the mobo.
 
noise is coming from PSU

replaced PSU

same problem.. ugh. the noise sounds like some electrical stuff too not very mechanical

did i really get 2 bad parts from newegg?
 
hm so when i have just the cpu, psu, and motherboard plugged in with the extra 2x12V connector, it seems to cut the power and start it again every 10 seconds or so the leds turn off and the psu fan turns off, then it comes back on without me touching anything?
 
The -5V was removed from ATX12V specifications years ago. It shouldn't be required at all.

What 2x12V connector are you talking about? Also see if a RAM swap helps
 
the 2x4 12V connector that is labeled as P3.

Without it, the PSU makes that high pitched noise, with it, the motherboard cycles power.

should the cpu fan at least turn on without any ram in? the only ddr2 ram i have is this OCZ 2.1V ram..
 
the 2x4 12V connector that is labeled as P3.

Without it, the PSU makes that high pitched noise, with it, the motherboard cycles power.

should the cpu fan at least turn on without any ram in? the only ddr2 ram i have is this OCZ 2.1V ram..

AFAIK, you need RAM on the motherboard for it to boot and therefore turn on the fan.

Also, there is no SilentXStream PSU. Did you mean StealthXStream? Also what other power supply did you use?
 
Do you have an old system you can "borrow" a system speaker from? If so, do so.

I'm guessing your RAM isn't getting enough voltage, but you'd need some 1.8v stick to get it to boot and change the DRAM voltage in the BIOS. Are those OCZ RAM sticks new? They should have an SPD table for 1.8v operation.

Also... from the sticky: Basic Troubleshooting Guide...

/*------------- <cut n paste> -------------*/
This is basic troubleshooting if your system has never POSTed (as in, you just put it together); Though, it may be helpful to others whose system no longer POSTs...
If you have both the 20/24 pin main ATX connector plugged in, AND the 4-Pin (or 8-pin) ATX12V P4 CPU connector plugged in, then the board should boot fine (unless it requires more power connectors from the PSU). First, try clearing the CMOS w/ the proper jumper or button.

The next thing you could do is test the PSU. Jump start it (on the main atx connector, short the green wire with any black wire, using a paperclip), and see if it stays on. If not, then its probably a faulty PSU. If it works then you can proceed with the suggestions below. ***NOTE: The paperclip trick is a simple test for those that do not have PSU testers, multimeters, nor a spare PSU to test with. It is not a 100% conclusive test of the PSU.

How to test with a multimeter @ BFG

Setup everything outside of the case, with the mobo on top of its cardboard box. Plug in only the essentials:
- PSU (namely: main 20/24-pin ATX connector and 4-pin ATX12V P4 CPU Connector; The 4-pin should work in the 8-pin EPS12v plugs, too)
- CPU w/ HSF
- Single stick of ram
- Videocard if there is no onboard video (along with its power connector, if it has one)
- System speaker/buzzer (your board may have an on-board tweeter/buzzer/speaker)
- Monitor & Keyboard

Reset/Clear the CMOS by following the instructions in your mobo manual.

* Use a screwdriver if your board doesnt have an onboard power switch. Jump the two power switch leads to turn the power on.

If it won't post, try different RAM slots. If it still won't post, pull out the ram (so no ram in the system) and listen for error beeps. If none, pull the vidcard and listen for error beeps. If none, re-seat the CPU and HSF, then try again. Report back with results if you're still having issues.
/*------------- </cut n paste> -------------*/
 
Back
Top