Man.....WT???

That sounds like a RAM problem actually. If the RAM is bad or overclocked too much (which I don't think is your case) and drivers don't load properly Windows will reboot every time. You can always reproduce this problem by overclocking RAM beyond what it is capable of doing and trying to boot the machine.
 
1st off, I can understand your problem, and I can see why your upset.

Now, calm the hell down Beavis! There are a bunch of people who come to these forums that dont like seeing curse words posted everywhere! It not only makes you look foolish, but like a noob also. Many will probably avoid this thread, because of the title alone. Even though the forums rules say it is ok to curse in the body of a message posted here, most people keep it in check!

Now onto your problem, are you using the same PSU as you had on your old machine?
If so, it is dated and probably doesnt have enough amps on the +12 rails to properly power your board.
 
Freemason115 said:
1st off, I can understand your problem, and I can see why your upset.

Now, calm the hell down Beavis! There are a bunch of people who come to these forums that dont like seeing curse words posted everywhere! It not only makes you look foolish, but like a noob also. Many will probably avoid this thread, because of the title alone. Even though the forums rules say it is ok to curse in the body of a message posted here, most people keep it in check!

Now onto your problem, are you using the same PSU as you had on your old machine?
If so, it is dated and probably doesnt have enough amps on the +12 rails to properly power your board.
That sounds like your problem right there. That hardware draws quite a bit more power than a 5 year old computer. Driver issues might also be a problem here. Take your old AMD thunderbird or whatever was in there before, and then suddenly pop in a crapload of new hardware, several generations past of chipsets etc, and there might be hardware conflicts :D

For the PSU, i'd refer to this thread and for your disk, i'd pop the old hardware back in there and back up anything you want to be saved, then go for a total reformat and reinstall of windows with your new hardware, along with new drivers etc.
 
There are potentially two problems here:

1. The PSU. This system will definitely draw more juice than your old one.

2. Did you do a clean format of your harddrive? There is no way windows 2000 or XP will post when you change mobos like that.
 
JL_Audio_User said:
Am I a fuckin beta-tester or what?

I took my old cus-lv mobo (came in a Sony Vaio back in 2000) out of my Aspire case and put in a A8N-SLI with 1024 of new corsair xms memory a new AMD3500+ and I get a windows "splash screen" then a restart...over and over and fuckin over again? Anyone know whats up?

A message to anyone who works for ASUS who might peruse these forums:

Instead of trying to put a buncha un-tested crap on a MOBO make one that fuckin' works!! I got an idea how about a self diagnosing mobo so after it re-starts itself for the 10th time in a row it...I dont know....maybe it could.....TELL ME WHAT THE FUCK THE PROBLEM IS!! Not enough of this...too much that. No I gotta climb into the fuckin BIOS risking doing more harm than good.

Fuckin thieves. I'm not a beta tester (till now) so fuck you!


You certainly dont come across as a beta tester. When you put your own machine together you are going to run into one or more hitches before getting the baby rock solid. Let me guess, you just got your A+ Certification and wont take any shit from any company that YOU cant configure thier motherboard correctly. Peace. :p
 
The guy's blamig Asus for Windows not booting when he changed to a completely new motherboard with a new chipset... HMMMM, WHAT COULD IT BE?!

If you took no measures at all BEFORE switching the motherboard to make sure there would be no driver conflicts, Asus is surely to blame! All the hundreds of people with this board that are using it happily on their systems are surely experiencing the same beta-testing problems.

Anyway, tell us what you did to prep the system up for a motherboard change, and we'll tell you why it's not working.
 
1st off, I can understand your problem, and I can see why your upset.
Now, calm the hell down Beavis!
Now onto your problem, are you using the same PSU as you had on your old machine?
If so, it is dated and probably doesnt have enough amps on the +12 rails to properly power your board


Sorry. Fuming over.

No I bought a brand new Coolermaster 450 Realpower. and I got brand new Corsair XMS Twinx1024 3200c2pro.

However...I am embarrased to say it ....but would be thrilled if it was the problem. The HD is the original out of the VAIO. (40 gig 5,400rpm 1mb cache ATA/100)<<<<Could this be the problem??


sorry bout the language. appreciate any help I can get from you all.
 
JL_Audio_User said:
Sorry. Fuming over.

No I bought a brand new Coolermaster 450 Realpower. and I got brand new Corsair XMS Twinx1024 3200c2pro.

However...I am embarrased to say it ....but would be thrilled if it was the problem. The HD is the original out of the VAIO. (40 gig 1mb cache ATA/100)<<<<Could this be the problem??
Could very well be. Are you using the cables that came out of the retail box for the A8N or the original Vaio's cables?
 
I had after market cables and did try the ASUS cables.

I'm really wondering if a 5,400rpm ATA/100 HD isnt cutting it with a A8n-SLI?
 
Tytanium said:
Could very well be. Are you using the cables that came out of the retail box for the A8N or the original Vaio's cables?
It actually is very unlikely to be the culprit. The fact that it's a slow drive does not mean it's a faulty one.
 
The manual says "Supports Ultra DMA/133/100/66 and SATA"

My HD doesnt say Ultra anywhere? or DMA for that matter just ATA/100. That would'nt cause it to shutdown after "splash screen"??
 
Anarchonixx said:
It actually is very unlikely to be the culprit. The fact that it's a slow drive does not mean it's a faulty one.
I did not say that the slowness of the drive is the reason. Just the fact that he hadn't reformatted it, and contained the original installation of windows on it when he tried starting up the new system.
 
JL_Audio_User said:
The manual says "Supports Ultra DMA/133/100/66 and SATA"

My HD doesnt say Ultra anywhere? or DMA for that matter just ATA/100. That would'nt cause it to shutdown after "splash screen"??

the chipset drivers try to initialize during windows boot. if they don't see the proper mobo, the whole system just freaks out and you get a constant reboot. You need to do a clean install of windows.
 
BigBadBiologist said:
the chipset drivers try to initialize during windows boot. if they don't see the proper mobo, the whole system just freaks out and you get a constant reboot. You need to do a clean install of windows.

Thanks. How would I do that? I put the XP CD in and nothing happens? No prompt nothing can I re-install the OS thru BIOS? The BIOS shows the DVD/CD and it spins up but nothing else?

again...thanks for any help or advice!d


also the HD makes a noise like someone hit the brakes on it at the moment the windows splash screen hits an then thats it.
 
Sounds like you have to set the boot order in the new motherboards BIOS as :>

CDRom
-Hard Drive

then boot off the CD and do a fresh install
 
JL_Audio_User said:
Sorry. Fuming over.

No I bought a brand new Coolermaster 450 Realpower. and I got brand new Corsair XMS Twinx1024 3200c2pro.

However...I am embarrased to say it ....but would be thrilled if it was the problem. The HD is the original out of the VAIO. (40 gig 5,400rpm 1mb cache ATA/100)<<<<Could this be the problem??


sorry bout the language. appreciate any help I can get from you all.

I have the same Ram and PSU, the PSU I know is very rock solid. But this is still putting me in the mind of a PSU problem. Or maybe the CPU fan is disconnected causing a quick cycle in the power for protection. BUt I had a similar problem, power up-would reboot immediatley. Was my antec 550 PSU, not compatiable with my AV8, but the Realpower 450 should work his machine just fine. I kinda getting stumped on this one, dbl check the fan connection and make sure its on the CPU fan header, I know on my board there are 2 fans connections side by side, and I had it on the wrong one causing a reboot, because no cpu fan was detected.
 
I have the same Ram and PSU, the PSU I know is very rock solid. But this is still putting me in the mind of a PSU problem. Or maybe the CPU fan is disconnected causing a quick cycle in the power for protection. BUt I had a similar problem, power up-would reboot immediatley. Was my antec 550 PSU, not compatiable with my AV8, but the Realpower 450 should work his machine just fine. I kinda getting stumped on this one, dbl check the fan connection and make sure its on the CPU fan header, I know on my board there are 2 fans connections side by side, and I had it on the wrong one causing a reboot, because no cpu fan was detected

Thanks for the help. Actually the cpu fan is connected correctly.
 
Tried booting with only 1 stick of RAM yet? Try that out, let us know, if it doesnt work try the other stick.
 
Freemason115 said:
Tried booting with only 1 stick of RAM yet? Try that out, let us know, if it doesnt work try the other stick.

Have'nt tried that yet. I'ts 12:am in Japan right now so I'm going to get some sleep but will try that Idea (as well as others) as soon as I get up. Which will be early since this is driving me nuts.

Thanks again!
 
Well do U have anything on that HD that U really need?

Otherwise Id clear all settings from the MoBo. (clear Cmos), U maybe even have to remove power and battery for a while but Ive always found it enough to turn off remove cord to PSU and then pzush powerbutton on computer - reinsert powercord and push powerbutton again and off U go. This way U should be given the chance to get into the BIOS and there U can reset the Boot order.

If U do have any documents U need to save on the HDD get another one and install on that. (buy 1 or borrow a friends spare (with no data on it)) install on the spare. install old HDD as slave. transfer all things U need from your disk to Spare.
Remove Spare and format/install on yours.

Reinstall spare as slave and copy documents back.
Wipe Spare
Return Spare
Say thank you and buy your very good friend some Sake :D
 
first off dont reformat you may not need to.
if you have an actual win xp cd and not a "recovery disk"
you can do a reapir install
if you have a recovery disk only you aint getting win xp to work period as it will load the vaio's hardware drivers instead of what you now have. so if it's a recovery disk go out and buy win xp first.


second.

at boot up press del key and go into bios.
under boot order select cd rom as first boot device (look in manual for how to set boot order too many variations to cover quickly)

reboot.

when prompted press any key to boot from win xp cd rom

ignore recovery console

go ahead and select install windows
it will then detect your previous installation and ask if you want to do a repair install.
do a repair install

load new drivers when win xp finished and then see if you have issues
 
With all that great hardware, and with having to load windows again I'd suggest investing $80 in a brand new western Digital 120GB SATA HDD w/ 8mb buffer, loading windows onto it and then transferring the data from the 5 year old 5400 rpm HDD that is about at the end of its life , probably, anyways. Why have all that speed just to watch the bottlenack at an out of date old HDD? ZipZoomFly has this drive for $78.95 w/ free 2 day delivery.
http://www.zipzoomfly.com/jsp/Produ...oryCode=011016&SortBy=B&Brand=WESTERN DIGITAL
 
follow wetware's advice. I've done that twice recently and saved my ass a boatload of time reloading crap. I haven't heard any complaints from the people I had to do it for either, and let me tell you I'd be the first to here it.
 
THANK YOU!!

To everyone. Wetware interface<<<You tha Man

Changing boot order and re-installing OS worked :)


1 more question if you don't mind?

My comp cant see my modem? I think Plug N Play is off by default on the MOBO is this why? Which of the 2 ethernet ports should I use? and do I need to do something in BIOS.

In the past I just plugged into the back of other MOBO's and the comp saw it. Again is this a UPNP thing?

Thanks for any help. I will tip a big glass of Japanese Shochu back tonight in honor of you guys. This forum is [H]ard.
 
You need to install the drivers for the ethernet ports. The drivers are on the motherboard disc, one port is on a Marvell controller, the other is an Nvidia.
 
AuroraProject said:
You need to install the drivers for the ethernet ports. The drivers are on the motherboard disc, one port is on a Marvell controller, the other is an Nvidia.

Fixed. Thank you!
I went from a PIII 886 to the AMD3500+ this baby flies :D

Anyone know why the external HD via 1394EEE isnt showing up as a drive ? I cant find it anywhere?
 
JL_Audio_User said:
Fixed. Thank you!
I went from a PIII 886 to the AMD3500+ this baby flies :D

Anyone know why the external HD via 1394EEE isnt showing up as a drive ? I cant find it anywhere?
Go into Control Panel > Administrative Tools > Computer Management

From there look for Storage > Disk Management (Local) and look for the drive. Right click on the drive letter and activate it. That should work.
 
Back
Top