Linksys WRT54G w. DD-WRT Wireless gone "missing"

Cobalt2112

[H]ard|Gawd
Joined
Jun 25, 2002
Messages
1,177
Hey gang,

For months I've been running a Linksys WRT54G w/ DD-WRT v23 SP2 Firmware. Today I come home and mysteriously my wireless is not working.

I pulled the power from the router for a minute and plugged it back in--Nothing.

I didn't change any settings from the day before.

Then, I changed the SSID, channel--Nothing.

The LAN works fine and my laptop can see other wireless networks in the area.

The wireless output is set to 60mW
 
That happened to me once. Had to take the sucker apart. Turned out the wireless card had come loose from the little mini-PCI type slot the card sits in.

So try taking the cover off and making sure everything inside is secure.
 
I'll try that, but I wonder how that would have happened? The router is in my office and sits on top of my Linksys 16 port switch. Even though the kids do have access, I didn't notice anything out of place.

But it never hurts to give it a shot.
 
That wireless output setting seems a bit high. I have a WRT54G ver3 with DD-WRT and the default is 38mW. If your router is supposed to run the same default as mine, then it's probably been running rather hot for a while and you may have fried the wireless chip inside of it.

That's the worst case scenario, but I wouldn't rule it out completely.

 
Hmm... I hope not. It's rather cool down here, but I'll give it a whirl. Dang, I think I have a Broadcomm card from a Belkin router... Let's see if it fits... It seems like a standard slot (ala SO-DIMM)

If not, I missed the BF deals and coulda bought one for cheap... or maybe I'll buy one with Gig-E and upgrade my network.
 
Update ... I lowered the mW output of the wireless from 60 to 50 and it started working again.
 
i have mine set to 85mW i also bought some heatsinks for the router when i first got it
 
hmmph mines been at 70 for almost a year now, no issues and its not like its in an ice chest or anything it gets warm in here... Never opened the thing up, must just be bad luck, good thing it works though!
 
Morpheus, I've got a boat load of heatsinks... what did you use to stick the HS to the router components? Good ole Crazy Glue?
 
As an eBay Associate, HardForum may earn from qualifying purchases.
OK, but what did you use to stick them onto the chips? Do they come with frag tape or something?
 
Ordered some Artic Silver Thermal Adhesive from the Egg and I'll slap some Dremmeled-up SB heatsinks.
 
Artic Alumina Thermal Adhesive arrived in the mail this AM. Gonna get heatsink happy!
 
Before I crack open my router, I wanted try the goop on my Radeon X1650pro ... I decided to cut a NB HS into 3 fairly even pieces...

SHOW:
img_1875.jpg
img_1876.jpg


CUT:
img_1877.jpg
img_1879.jpg


Please comment on the GLUED job... was it too much goop? For the bottom one, did I not press hard enough? I see a gap there or will the goop conduct?
GLUED:
img_1886.jpg
img_1886-2.jpg


Just for kicks... I may attach these to the Volt Rectifiers on my X1950gt... Gotta sand them down. I use Autobody 1500 grit, leaves it super smooth.
img_1880.jpg
 
That's odd about your transmit power on the WRT. I bet it is a cooling issue though. I run my WHR-G54S with DD-WRT cranked up to 100mW. One time it did poop out on me with the same problem you are describing, I just did the reset to factory defaults and reprogrammed it and it has worked without issue for over a year now. I also set it to reboot every day at 5am and it sits in my basement where its 65F year-round so that may have something to do with it as well. . . . . .

 
Weird. I'm running at 128mW and have been for a year, year and a half now with no issues. My room is a little coolish (67-8 on average), but nothing too out of the ordinary.
 
Hmm.. maybe it was a random lockup? Anywho... good excuse to now use the ASTH and brick my router! Maybe it'll cause me to move to WiFi-N + Gig-E

However, does the application of the goop look OK?
 
Back
Top