Just built my first computer, nothing displays on bootup...

Kc98GT

n00b
Joined
Apr 14, 2008
Messages
4
Hello everyone,

I just recently put together a machine and when I start up the system it runs smooth with no noises, but no video will display on the screen.

Here are the pieces that I put together:

ASUS M2N32-SLI Deluxe Wireless Edition AM2 NVIDIA nForce 590 SLI MCP ATX AMD Motherboard

AMD AM2 Dual Core 6400+
Nvidia 9600 GT 512 MB
WD 160 GB EIDE HD
4 GB Corsair DDR2 800


I actually RMA'd the Motherboard when I tried a spare PCI-E card that I knew was good and it would not work.

I got the new Motherboard and had the same exact problem with no video displaying on the screen :confused:

So I bought a new processor to see if that would solve the problem, and sure enough, it still is doing the same thing.

I'm guessing the only alternative left is a bad video card. I was wondering if this could be a common error (hardware or user) that some of you might have some insight on.

-Karl
 
Sounds like a power supply issue, actually. Your fans and lights can often turn on even if your power supply is having trouble.

Make sure it is all connected properly. Also, make sure the 110v/220v switch is on 110v (yes, I ran into that issue once).

After that, I would try pulling a PSU from another computer and see what that does.
 
I totally failed to mention the PSU. It's a 650 W I don't have a brand name but I had my doubts that it was a quality PSU. I'll test be able to test out the PSU and Video Card tonight i'll check for that switch, Thanks!
 
It's not clear from your original post exactly what your symptoms are when you boot up. When you say 'it runs smooth with no noises' do you mean that you can get into windows and hear the startup sound, but no video displays on the screen? Or do you mean that there are no beeps from the motherboard, but nothing ever happens beyond the fans turning on and the hard drive spinning up?

If it's the former, I would check the cable from the vid card to the monitor. It it's the latter, I would check the RAM. Failure to POST is a classic dead RAM problem.

Hope this helps,
knobbicus
 
The answers to knobbicus's questions would help a lot.

I might be assuming a little too much. I've dealt with a lot of PSU problems. They all start out with "it sounds like it is booting up just fine" even though it is just the fans making noise. So when you said, "the system runs smooth with no noises", I assumed you meant it sounded like it was booting up and it was not making any beeping noises.

Let us know how it goes. :)
 
When I boot up the computer all of the fans turn on(CPU,Case, and Video Card.) The monitor never turns on, it just sits there like it is not getting the signal. The video card has it's external power source plugged into it and the fan is running.

Before I RMA'd the first board I booted the computer up about 6 or 7 times and nothing happened. I actually did somehow get the BIOS screen to output on the monitor on about the 8th try or so, but the machine locked up without response when I tried to get into BIOS. Since I installed the new motherboard I have not been able to get anything to display on the monitor.

Thanks for the responses.
 
take out cmos battery and short cmos pins for about 10 seconds with a flathead. wait a few minutes then replace battery. and why not reseat all components. good luck
 
Try giving it a situation in which the motherboard should beep (unhook power from the video card, take out the cpu or ram, etc) and see if it does.

If it does not, I am going to put my money on PSU. :)
 
This might sound like a pain but reassemble your system outside of the case with the mobo lying on the mobo box. Start up the PC by jumping the two power pins with a screwdriver. If there is video, then something inside the case was shorting out the mobo.

Look for any loose screws, wires, or standoffs that shouldn't be there.
 
Both Danny's suggestions, and the people advising PSU sound reasonable to me. I would also clear CMOS, because it's easy, doesn't require any part swapping, and might fix it. Your manual can help if you haven't done it before.

Good luck,
knobbicus
 
I had a chance tonight to try some different RAM a friend had, and it ended up solving the problem. The display showed up immediately asking for the O/S.

Thanks for all the ideas; coming from a first time builder I was really hoping this wasn't caused by user error :cool:
 
yep I actually just had this problem with bad memory... swapped vid cards, mobos, everything. finally caught on to the POS ram being the culprit

Oh well, nice build. Enjoy !
 
Back
Top