Intel 5000x and Raptor WD800

MikeM64

n00b
Joined
Sep 15, 2010
Messages
6
Hello Everyone,

I just picked up a used Dell Precision 490. (1xXeon 5160, 2gb DDR2-FBDIMM, 80GB Raptor, Intel 5000x chipset). I'm having a huge issue with the HD stalling. I'm running just the single drive on Windows 7 Pro x64. If I have it set to AHCI in bios, then on boot and every 10-20 mins after the computer stalls for about 5 minutes. During that time, the HD light is solid and it doesn't sound like the HD is doing anything. Towards the end of the stall, the HD starts going again and then the system goes back to normal. If I switch back to ATA in bios (Sata Mode), everything is fine, though a little slower. Is there a way to get it to work without stalling in AHCI mode?

Also, are speeds of 60-70mb normal for a raptor?

I've had this issue in Windows 7 x64, Windows XP, and Windows Server 2k8 R2.

Thanks,
Mike.
 
Is this a clean install on that raptor in AHCI mode? Raptor have any issues when you test it? I haven't had any issues with the 160 GB Raptor on my Precision 690, so I doubt it's the chipset itself, unless something is borked. What port is it plugged into, the Sata or SAS?
 
Also, are speeds of 60-70mb normal for a raptor?

Probably. That is a 3+ year old drive.

During that time, the HD light is solid and it doesn't sound like the HD is doing anything. Towards the end of the stall, the HD starts going again and then the system goes back to normal

I would still check CrystalDiskInfo the drive could be dieing.
 
Is this a clean install on that raptor in AHCI mode?

Yes. It stalls during the install too.

Raptor have any issues when you test it?

How would you recommend I test it?


I haven't had any issues with the 160 GB Raptor on my Precision 690, so I doubt it's the chipset itself, unless something is borked. What port is it plugged into, the Sata or SAS?

It's plugged into SATA0. I do not have a raid card in it.

Drescherjm, The drive works perfectly when it is not in AHCI mode. Also, CrystalDiskInfo shows that it's in good health, albeit used for 24807 hours (~1033 Days - Manufactured Jan 2007)
 
Hmmm...I know the 690 has 2 SAS ports on the board, not sure if the 490 did, I thought it did though, you could try those if you do.

Also try WD Diagnostics test to see if it shows anything. Is it still under warranty?
 
Hmmm...I know the 690 has 2 SAS ports on the board, not sure if the 490 did, I thought it did though, you could try those if you do.

Also try WD Diagnostics test to see if it shows anything. Is it still under warranty?

There are no SAS ports, and the 490 needs an add in board for them.

Quick Diagnostics show all is good. Extended ones are still running.

Unfortunately the HD is out of warranty.

[EDIT]: Extended diag's finished. All good. Though it says spin up time (value 169 - threshold 21 - worst 166) and raw read error rate (200 - 51 - 200) are "under warranty." Weird terminology in the program.
 
Last edited:
Test with MHDD32 on Ultimate Boot CD. That drive is old and not good and I'd rather have almost any modern 7200rpm drive and possibly even some modern 5400rpm drives.

Also, check what AHCI option ROM version (also RAID option ROM version if you use it) you have when you boot the comp. Make sure your BIOS is the latest.
 
That drive is old and not good and I'd rather have almost any modern 7200rpm drive and possibly even some modern 5400rpm drives.

An 80GB raptor from 3 years ago will be slower in most things (if not all) than a modern 7200 RPM drive with 500GB platters. Seeks may be a little faster on the raptor but being that it is only 80 GB I would expect if you short stroked a 500GB platter drive down to 80GB you would get good seeks as well. Also the raptor uses more power and thus heat than a current generation disk.
 
Last edited:
Back
Top