I have a Question about my PC

4LC4PON3

DERP!
Joined
Jan 18, 2005
Messages
4,230
Ok i recently upgraded my Graphics card to a HIS 4850 and was told my PSU isnt good for this Card.

Specs:
Dualcore 4450e
ECS Mobo
3gb ram
1 DVD DL burner
640GB sata WD HDD
Antec earthwatts EA430 430W: http://www.newegg.com/Product/Product.aspx?Item=N82E16817371006
HIS 4850: http://www.newegg.com/Product/Product.aspx?Item=N82E16814161244

My question is i posted up on the ati forums about my card was asking a ? and someone asked me my setup so i told them. then some people went nuts saying that my PSU is not good enough to run my vid card

one of the comments: you'd do the card a LOT of justice by running it from a certified and capable PSU aswell, that unit ain't rated by ATI for a single HD4850 .. your PSU outputs 17A MAX @ 12v or ~14.5A and your card draws around 15.5A under load .. you're gonna run it into the ground or something might go POP if you run it close to the limits of that unit

am i worrying about nothing or is he correct. I was told by some hardocper's to get this card and PSU so i did.
 
According to gpureview.com, the max power draw for an HD4850 is 110W (110/12 = 9.17A). Where did that guy get 15.5A? :confused:

As for your whole system, its using under 300W at full load.
 
not sure but his signature sais

GG ( Moderator @ SapphireTech's VGA / Mainboard Help Forums ).
 
The EA430 was first made by Seasonic, but I believe Antec has switched to the EA430D, which is being made by Delta.

ATI Certified Single card PSUs: http://ati.amd.com/products/certified/powersupplies.html

Seasonic is on that list, with their SS-430GM, aka M12II-430 (SS-430GM Active PFC), which has similar specs to the Antec. Actually, they have mulitiple 430W models on there, most likely all with similar specs and certified to run an HD4850.

Seasonic SS-430GM Active PFC F3 (430W)

Radeon™ HD 4870 & 4850
Radeon™ HD 3870 X2
Radeon™ HD 3870 & 3850

http://www.seasonic.com/product/pc_retail.jsp -- 360W / 12V = 30A on the combined +12V rails.

Again, its not the same platform, but similar specs, yet its certified. Since the specs are similar, I find it hard to believe the Antec is inadequate.
 
Last edited:
your PSU outputs 17A MAX @ 12v or ~14.5A and your card draws around 15.5A under load .. you're gonna run it into the ground or something might go POP if you run it close to the limits of that unit

am i worrying about nothing or is he correct. I was told by some hardocper's to get this card and PSU so i did.

Earthwatts PSUs don't have multiple 12v rails; they have only one 12v rail with no limiters on any of the connectors. Your PSU has 34A on one rail, and can certainly handle any card with a single 6-pin PCI-E power connector. Earthwatts PSUs are one of those cases where the PSU is actually better than the specs say rather than the usual worse.

http://www.jonnyguru.com/modules.php?name=NDReviews&op=Story2&reid=35
 
sweet thanks for all the info.i dont typicaly listen to anyone but hardocp users but this time for some reason i let someone get to me lol
 
not sure but his signature sais

GG ( Moderator @ SapphireTech's VGA / Mainboard Help Forums ).

Well that's a big red flag right there. Sapphire's forums are pretty much full of ignorant people, moderators and members alike. So any "advice" from them should be taken with a grain of salt.
 
Back
Top