Help Me, I got nothin...

Lugztaz

[H]ard|Gawd
Joined
Jun 21, 2004
Messages
1,783
Alright here's the deal(story)

I have an Asus A8N-SLI Mobo, an EVGA GeForce 7900GT Video card, 2 Corsair XMS3200 1GB memory sticks and an Enermax ELT500AWT PSU.

Awhile back probably about 4 or 5 months ago the video card started to act up, displaying lots of dead pixles on multiple monitors. I put in a regular PCI video card and sent in the other one. Gets back everything works fine. Now about 3 weeks ago I sent in the memory due to memory errors with one module. I got them back and I put them in, started a format.

While installing windows I noticed some very odd characters and blocks. I boot after windows install was complete and now the pixles are back. There are randomly dead pixles on the monitor, during POST, boot and in windows.

I put in another video card again, works fine. So I took everything out of the case, I set it up to run on my desk. I start it up and I notice that the chipset fan is making lots of noise. I unplugged the 6 pin power source from the video card and booted again. Now the chipset fan is not making any noise... I go into the BIOS and notice that the chipset fan says it's running at 6k RPM. I hook the 6pin back up and it starts to grind again. Into bios I see the chipset fan is only running at 2400 RPM...

After trying this a few times the chipset fan has stopped grinding. There is some dust but not much on any of the devices, I really can't figure out what it is. If anyone could give me some ideas that would be great. I don't have another PSU to try as this mobo needs the 24 pin and no other mobo to try the video card in right now so please consider that.

If you need anymore information please just ask.
 
checked your gpu fan recently? i can't imagine a 7900 artifacting on install though.

first check voltages, then run atitool to check for artifacting. also memtest might be in order.
 
If you have a 20pin PSU then you might be able to get away with leaving the last 4 pins empty just to test the PSU out. Some boards are picky won't work right without all 24 pins. But it's worth a shot just in case is does prove your PSU is bad.
 
Alright, i will run ATItool here in a minute. I will also try another PSU just in case. As for memtest, host many passes should I do? Last time I did it off of an ubuntu disk it ran through all of the tests and started over but still only stated 0 passes so I wasn't sure there. I'll try it before bed. Thanks for the ideas and more would be appreciated :) .
 
Alright, i will run ATItool here in a minute. I will also try another PSU just in case. As for memtest, host many passes should I do? Last time I did it off of an ubuntu disk it ran through all of the tests and started over but still only stated 0 passes so I wasn't sure there. I'll try it before bed. Thanks for the ideas and more would be appreciated :) .

Well there's 8 tests per pass and it take my 1GB DDR400 computer about 30 minutes to finish all 8 tests.
 
Ok I ran that ATI Tool and It just looked like crap, couldn't read anything at the bottom. So I threw in some crappy walmart video card and it can what looks normal for the card but I'm not sure.

I put the card back in w/ no external power and a message came up that I have seen pop up on the computer before but it went away too fast. It was saying not enough power was being delivered to the video card so it powered down. I'm guessing this has something to do with it but i'm using a 500w PSU, should it be bigger? Other specs I didn't list below were the processor is an x2 4200 I think and a 10k RPM HDD and another 7200. Let me know if that helps any.

Note the test was ran with the external power.
 
Alright Im running memtest right now. Should I do it with one stick at a time or both 1 gig sticks? It says it has all 2048MB cached and its running the test so ill let you know how it goes.
 
Alright, 15 passes later I see zero(0) errors. Obviously the video card is messed up again, but how do I know it isn't the mobo that is causing these sporadic problems? I really don't want to have to keep sending in the video card if it is the mobo. Any ideas or should I just try getting the card replaced and going at it again?
 
Have you tried another PSU? an unstable PSU will cause many many problem. And seeing that when you load the 12v rail with the video card and your chipset fan slows down and makes noise would be a good indicator of such.
 
No, I'll try that when I get home tonight. I decided to go ahead and install all other drives on the system. I installed the asus chipset drives, restarted and now i'm getting the old " Windows could not start because.... Missing system32\DRIVERS\pci.sys" sigh
 
Have you tried another PSU? an unstable PSU will cause many many problem. And seeing that when you load the 12v rail with the video card and your chipset fan slows down and makes noise would be a good indicator of such.

+1

another vote for the PSU.
 
Alright right now im running a new PSU, still using the crappy card and reinstalling windows. The chipset fan was still making noise, I tapped it a few times and it quit, I think it might just be going bad so that's when it showed the speeds because it's getting jammed or something.
This is only a 350w PSU and it has no 6pin connector for the GeForce video card. Looks like it froze during setup, trying again. :rolleyes:

Alright so apparently when using a molex to sata power adapter you don't match red to red, black to black and yellow to yellow because when I did this it fried the hard drive? WTF? Alright WDC is going to send me a new one. After windows froze and I shut it down, it didn't want to show video. Ok I tried twice and nothing. So I put in the other video card and it worked but it said there was no HDD. I made sure the connectors were in and restarted. Boom dead HDD. I quit tonight.....
 
Back
Top