Help! Computer won't boot from SATA drive

rage4order

Gawd
Joined
Oct 4, 2004
Messages
795
Well, after lots of troubleshooting, I finally figured out that my mobo is bad. So I replaced it but now I can't get it to boot from my SATA drive. I booted from my XP disc and installed the drivers, went into the bios and it shows my sata drive in there, but I can't get it to recognize it as the primary master drive. I even disconnected my IDE drives and it still wouldn't boot from the SATA drive. Any ideas what I should try next?
 
During the install, did you press F6 to install the SATA drivers for the mobo?
 
yep, some mobos need a driver in the windoze installation to get the SATA to work
 
Did you install the drivers using F6 before or after you disconnected your IDE drives.
If after then the boot files could well be on the IDE drive.
Its why I always install Windozes with only one hard drive attached.
That way I know where its putting the boot files.

With all other hard drives disconected if Windozes sees the SATA drive durring the install then it will set it as your primary boot drive.
You may have to set it back to your main boot drive after you reconnect your IDE hard drives.

You can either try to fix the boot files or just try reinstalling with only one drive attached.

Luck ........ :D
 
1)yes, I hit F6 and installed the drivers
2)I have my IDE drives disconnected when I did the driver install
3)This is not an install. I was hoping I could just swap out my mobo and be back up and running without reinstalling windows.
Will I have to reinstall Windows? I did see the Windows screen pop up for a split second during one of my boots but it just does not want to run.
 
You should always reinstall Windows XP after a mobo switch. Or else stuff like this happens.
 
http://www.aumha.org/win5/a/wpa.php

Can you boot into safe mode? Hold down F8 after the system POSTs.
I'm not able to boot in safe mode. I actually get to the point after the POST where it gives you the option of starting in Safe Mode, Last known good config., Start Windows Normally, etc., but it won't boot into safe mode. It actually starts to boot in Safe mode, but then just stops and reboots. I've also tried Safe mode with Command Prompt but it does the same thing. Will doing it the "F8" way make a difference?
I'm gonna probably just do a fresh install tomorrow. I have the Pro edition so I'm not worried about the activation. I'll just back up all my data on my other pc and then do an install. Would like to have avoided this, but hey, what can ya do?
BTW, the line that it freezes on is "WINDOWS\system32\giveio.sys" command.
 
Windows is rebooting because it's looking for hardware that isn't there anymore. Boot from the XP disc and reinstall as an upgrade. That will reset your hardware config so Windows recognizes your new board.

Caveat - often works, sometimes doesn't, sometimes works but with glitches. But, if you didn't try it you'd have to do a clean install anyway so what can it hurt?

BTW please tell me you practiced Golden Rule #1 and you backed up before making your hardware change. :eek:
 
Windows is rebooting because it's looking for hardware that isn't there anymore. Boot from the XP disc and reinstall as an upgrade. That will reset your hardware config so Windows recognizes your new board.

Caveat - often works, sometimes doesn't, sometimes works but with glitches. But, if you didn't try it you'd have to do a clean install anyway so what can it hurt?

BTW please tell me you practiced Golden Rule #1 and you backed up before making your hardware change. :eek:
No, didn't back up my drive but before I do anything, when I get home tomorrow I'm gonna copy it onto my other pc with Ghost. Then I'll try what you said.
 
Ok, did a clean install on a spare IDE drive and I'm up and running. Now, another question- could I have gotten a bad CPU from Newegg? Reason I ask is I'm back running with my 3000+ but when I swap out and put my new 3200+ in, I get nothing- no POST, no beeps or anything. I've tried reseating, disconnecting any unnecessary hardware and swapping out memory but the same result. Popped my 3000+ in, and it boots like a charm. Is my CPU bad? Sheesh! I've never had so many damn problems :mad: !
 
Ok, did a clean install on a spare IDE drive and I'm up and running. Now, another question- could I have gotten a bad CPU from Newegg? Reason I ask is I'm back running with my 3000+ but when I swap out and put my new 3200+ in, I get nothing- no POST, no beeps or anything. I've tried reseating, disconnecting any unnecessary hardware and swapping out memory but the same result. Popped my 3000+ in, and it boots like a charm. Is my CPU bad? Sheesh! I've never had so many damn problems :mad: !

Either you have a bad CPU or you need to flash your BIOS with an update that supports it. Find your BIOS version and check the rev notes to see if the 3200+ is supported. If not, time to flash.
 
Either you have a bad CPU or you need to flash your BIOS with an update that supports it. Find your BIOS version and check the rev notes to see if the 3200+ is supported. If not, time to flash.
God I hope it's just the BIOS. I really don't want to go thru the trouble of an RMA.
Thanks for the tip.
 
Did you have Speedfan installed? Speedfan uses giveio.sys and if you switched motherboard and it is looking for temp sensors that aren't there or are a different type than it thinks should be there it could cause problems.

Also (and yes I know this is strange) try booting will all of your USB peripherals unplugged.
 
No, I don't see Speedfan installed anywhere. Checked the BIOS and it's the latest version. I don't have any peripherals plugged in except my video card cause I don't have onboard video. It's gotta be the CPU because I popped my 3000 back in and it booted right up again. Put the 3200 in and all I get are fans spinning and nothing after that. Weird thing is my CD drive is spinning away also, but that's it. I also tried disconnecting that cd drive to see if that would help but same result. Looks like I'll be doing an RMA on that processor :( .
 
Back
Top