First time OC. Suggestions and so on?

Joined
Jan 3, 2006
Messages
912
I wanted to thank all the people who post in this forum and in my threads because you all are a huge resource whenever I am trying to figure out my computer. I used an athalon 1Ghz for a really long time and never got into overclocking because a lot of my parts were generic and not the best. My motherboard and video card died so I finally had an excuse to just buy a whole new system and am loving it. Didn't realize the difference between what I had and what I have now was this much. I was happy with stock but everybody online mentioned how easy it can be if you or not pushing limits and the c2d's have a fair amount of capability. So simply for the hell of doing it I read up and tried it.

I have an e6300 running at 400x7 right now, gskill ddr2 800 ram running w/ 2x multiplier, evga 7900gs ko set at 615/1590.

I need to improve my temps as I am running 52 idle right now with the stock intel hs, with 66 at the highest when loaded under TAT or orthos. I would guess that it has to do with not having experience with applying thermal paste. I am ordering a new heatsink when I save some money up again. Computer hit the wallet hard.

My graphics card runs at 44 idle and ramps up to 60 at the highest. Hovers around 56 avg when running 3dmark, playing games, rthdribl.

I have not adjusted any voltages except I put my ram at +0.1v. Cpu fan is on auto.

For some numbers. My pcmark05 score went from 5370 to 6820. My 3dmark06 score went from 4451 base with no OC, to 5216 with a GPU OC, to 5513 after all was said and done.

Memtest ran 6 passes fine, ran 3dmark and pcmark a couple of times along with rthdribl. Ran orthos for almost 2hrs and everything was fine. Didn't want to leave it any longer at those temps. Once I order a new HS I will run the tests overnight.

My main questions were, could I run it daily at those temps for a couple of weeks till I order a HS? Are the benchmark numbers sounding about right? If my ram is rated from 1.8v to 2.0v what should I run it at if all the settings work?

superpigv6.jpg


 
IMO thats a excellent job, temps are as to be expected with stock HS, if its stable during long gaming sessions you are golden, dont need to change anything, and can look forward to some real fun when you can get a better heatsink. You can run that as much as you want. Leave the memory where its at, you can try raising the voltage later when it starts to be overclocked when you start raising the FSB from 400.

You might want to disable the fan control, EIST, TM2 (thermal monitoring 2) to force the fan to run full speed, it will be noisier. Your call.

In case you have not seen it, this seems a fair heatsink write up.
(more for the historical comparision of what are regarded as the current best air cooling, than any one particular HS, also factor in the noise when making a decision).

http://www.anandtech.com/casecooling/showdoc.aspx?i=2943

Couple of them use the push pins, Fluke found this to replace them, looks like a great idea.

http://www.svc.com/lga775-bolt-th.html

original post
http://www.hardforum.com/showthread.php?t=1166791
 
All that stuff is disabled in the bios. I will try setting the fan to 100% and see. I would prefer the scythe ninja for the 120mm fan if I decide to run it at 100% and will most likely go in that direction. I have some yate loons that are nice and quiet at full speed. I already have 9 fans if you count every single one on gpu, cpu, psu, case so I can't care about noise as much.

The cpu fan mostly runs between 900-1200 rpm at those idle temps.

I just applied the as5 today so hopefully it will drop even more once it sets.

I did not touch the Vcore so it is still at normal (1.325v). Is the value you were asking for the same thing also as what CPU-z reports as Voltage under the processor section? If so then that value is 1.264v to 1.28vv
 
Those temps seem way high to me.. I think you need to re-seat the HSF.
 
Back
Top