First problems with Velocity Micro build..

coachjohn

Limp Gawd
Joined
Jul 10, 2006
Messages
234
I've had my Gamer's Edge since late August. When I first received it, I had some problems with the then current build of Everest Ultimate - it caused random reboots - that was later fixed with version 3.5. Since then, things had been very stable - perfect, really - until the last week or two. I've started having random reboots...literally out of the blue reboots, where system would turn itself off and reboot. Two of the reboots came with messages upon reboot of "Microsoft Windows has recovered from a serious..." and, when I sent the error report, MS's knowledgebase reported back that it was likely a driver issue but they couldn't be sure. I haven't overclocked the system...it's happened without pattern, once when just using IE and browsing the web, once when shutting down Madden 2007, etc. I have Everest Ultimate installed, but it hasn't been in use (either at the moment or during the session) when the reboots have occured. After one of the reboots, I've noticed that my C: (WD 2500JS) has started to make some clicking noises during boot...usually not a good sign.

I was an early adopter of Core II Duo, and the motherboard offered by VM at the time was the ASUS P5N32-SLI SE Deluxe. A bit of sleuthing on the web shows that there are a few other people out there having random reboots with this board as well. I've got the current BIOS on the board, I have current drivers for my hardware (updated NVIDIA driver thinking perhaps the display driver was the issue...but had another reboot after installing), etc. Not running anything odd or unusual...AV (NOD32) is current, as is Spyware Doctor from PCTools, and scans show a clean system. I'm thinking seriously of going through VM and seeing about upgrading to the EVGA 6800i board they now offer with the system (depending on cost)...also worried about the noise from the HD.

Any thoughts/comments on something else I should check? Temps for the motherboard, the CPU, the GPU, etc. are all good. Using the Antec TruePower 550W power supply, should be plenty for this build...have Artic Cooling Freezer 7 installed by VM when built, so pushing a good bit of air around..I sent Heather (customer care) an e-mail this morning, see what she says when she gets back from Thanksgiving holiday. Any ideas appreciated.

Have a great Thanksgiving. :)

John
 
I know Antecs have some issues with their caps. You may want to see if you can get the PSU replaced. I wouldn't recommend opening it unless your warranty has expired or has been already voided.
 
...and the warranty is still in place and hasn't been voided. I'm a pretty straight forward user...a lot of Photoshop CS2 (a photographer), a little bit of gaming, but nothing like overclocking, etc. Thanks for the suggestion..I'll see what VM says.

John
 
I agree, hard drive clicking and random reboot sounds like a psu issue or maybe RAM failure......

I had a similar issue as yours when I tried to install some fancy lighting in my case. The current draw was just too much, everytime I hit the on switch for the lights, the HDD would click and the system would reboot. (the lights were on the same molex as the HDD)

I'm sure VM will make it right with you.
 
...I hadn't even thought of a PSU issue; 550 watts should be more than enough for what I've got hooked up (E6600 CPU, 7900 GT, 2 250GB HDs, two Lite-On optical drives, Audigy 4 sound card)...unless it is a faulty unit. What's wierd is that is had been so stable...no, over the last several days, very unstable at times, stable at others.

I have no doubt VM will take care of me in some way...they've been great to work with, particularly Chris Morley and Heather Taylor. Good people. :cool:

I'll keep this posted to see how it all turns out. Have a good one.

Joh
 
I've sent the PC back to Velocity Micro...they are replacing the PSU, testing the memory, and, on my own, I'm upgrading the motherboard and the C: drive. Moving up to the EVGA 6800i motherboard and a Raptor drive...I am asking them to test the C: drive that was originally installed though. PC went out last night, VM thought I might have it back in a week. As always, working with Heather Taylor has been a very positive experience.

John
 
Have had similiar problems with a new Gamers Edge computer (T1315).... random crashes and lockups. Exactly the opposite experience with their tech support, however. They punted me to the Geek Squad. 5 Trips to them (who shipped it twice to Kentucky) suceeded only in damaging it beyond repair. They replaced it with the same model, which had the same problems. Tech support never solved the problem, or offered to do anything more for me. I finally returned my very expensive paperweight to Best Buy today. What a letdown.
 
....that you've had a bad experience...and I'm not sure if going directly through VM (as I did) and buying through Best Buy (as you did) limits their warranty options/tech support because of their deal with Best Buy or not; but to date my experience with them is that they bend over backwards to make it right. Did you ever contact the folks at VM directly? Or did you always go through your Best Buy dealer?

John
 
One of the reasons why I would never buy from Worst Buy, if you're going to buy a computer buy it direct from the vendor.
 
Chaos_UD said:
Have had similiar problems with a new Gamers Edge computer (T1315).... random crashes and lockups. Exactly the opposite experience with their tech support, however. They punted me to the Geek Squad. 5 Trips to them (who shipped it twice to Kentucky) suceeded only in damaging it beyond repair. They replaced it with the same model, which had the same problems. Tech support never solved the problem, or offered to do anything more for me. I finally returned my very expensive paperweight to Best Buy today. What a letdown.


Dealing with customers that bought their systems from Best Buy only gives us another avenue to solve problems. We will give the same depot repair service to BBY customers that direct customers receive, but if a customer wants a faster resolution (or begin resolution faster) they have the right to take the system back to a local Geek Squad precinct for immediate assistance. I'm very sorry to hear that your system did not work out, as that was a fantastic system at a really great price.

In the future, you can always call us directly for support even with BBY purchases, although it is not on-site. I'm also sorry we failed you. I'm happy to try again if you want to take another shot at it!

Randy
 
....your attention to forums like this one, and your personal interaction with your customers - as well as the point people in your employ like Chris Morley and Heather Taylor - are, for me, the single biggest reason I ended up going with Velocity Micro. You make a great PC and, for the quality of the build, you make it at a fair price - but personal attention goes a long, long way to building a loyal customer base. More companies should take notice of your business practices.

John
 
I decided to give Velocity another try. Bought an E2210 a few days ago, It had the same lose wiring problem someone else described, and the CPU fan got caught (now getting a "low fan speed" error message on start up). Loaded BF2142 and it crashed to the desktop in the first 5 min. Not looking too good...

I'm not going through the same c*** with the geek Squad again, so I'll let you know how Velocity's tech support handles it.

BTW, I sent an e-mail describing the problems with my first 2 PCs to Velocity, and was promised a response by Heather Taylor which (2 weeks later) I haven't yet received.
 
Chaos, I've actually sent you an email via these forums in an effort to get in touch with you. I hadn't gotten a note from anyone that you've asked to speak with me, and for that, I'm very sorry. Could you send your contact information to me at htaylor@velocitymicro.com? I want to make sure that this is resolved quickly for you.

Thanks!
 
...once you send Heather your contact info, I'm pretty confident she'll take care of you. I'm a tech skills instructor at a private school, and have dealt with reps from several PC companies; Heather is in a class by herself. Personal intention, a genuine interest in making it right, and very attentive to the little details. I imagine with the Christmas season upon them that Velocity is swamped...and she has still been able to keep me abreast of what is happening with my PC. I hope it all works out for you.

John
 
....can't wait to check it out. VM replaced the PSU "just to be on the safe side" and upgraded it from the Antec 550W to the Enermax NoisetakerII 600W. I upgraded the system drive to the Western Digital Raptor 150 and the motherboard to the eVGA 680i; Alfred, the tech who worked on my PC, was in touch with me almost daily to keep me abreast of where he was in the process, to confirm my needs/wants, and to let me know how things were going. Heather was also an integral part of the process throughout. Of all days, won't be home until late tonight...but will have it fired up either then or VERY early tomorrow morning. Should be interesting to see how things compare.

Kudos to the folks at VM for the experience while the machine was gone...now to see how things look upon arrival!

John
 
The new board 680i seems stable...none of the issues that I've read about yet...love the new Raptor drive...and they did upgrade, as mentioned, the PSU...but I'm getting some high temps. Previously I was getting Core Temp readings of 38C (at idle) consistently...now, 54C consistently (also at idle) with the new motherboard and PSU. (For more info, http://www.hardforum.com/showthread.php?p=1030337215#post1030337215)

This is a stock config as sent back from Velocity Micro...with the Artic Cooling Freezer HS and cooler. Seems very high...have left a message for Heather and am hoping this can be taken care of without sending it back again...

John
 
We've had all sorts of problems getting correct readings out of our monitoring apps. I'd try Systool and the Intel app as well to see if any of them give a more reasonable temp.
 
The Intel App (TAT) gave me the same reading...haven't tried SysTool. Thanks for the heads up. Were the problems with an accurate read just with this board?

John
 
Put the CPU under load and see if it spikes. It should go up dramatically on air-cooling. If it doesn't spike, then the reading is incorrect.

But a word of advice. I've gone through the same thing with my Core 2 Duo board. Bottom line, if it's stable, don't worry about it.

remove the heatsink, re-apply it, and look at the temps if you're curious, but I wouldn't lose any sleep over 54C. That's well below the dangerous threshold.

My CD2 cpu idles at 42C, 60C load on a Zalman 9700 just FWIW.
 
...As soon as I hear back from you, John, we'll get a tech out there to repaste/reseat that CPU for you today. You shouldn't have to send it back for anything--this is something that can be easily addressed on-site.

(I didn't know if you'd check your email or this site first, so I figure this way...I'm covered. Heheh.)

Heather
 
...I have to admit that I'm a little disappointed. Not in Velocity Micro, really...they're doing everything they can to rectify the situation...but just in the situation itself. After 1 1/2 weeks without the PC for upgrades/testing/etc. I'm back to without the PC again. When Mike - the tech sent by VM for repairs (prompt, easy-going, but he did say he had never worked with this particular HSF before) - arrived, I had the PC unhooked from all peripherals, power, etc, and up on the desktop ready to open up. Mike removed the HSF, cleaned off the old thermal paste, and went to reseat the Artic Cooling Freezer Pro 7 - and couldn't. One of the little pins that go into the motherboard was bent. He removed it, tried to straighten it, and tried again - no luck. After several tries, it became evident that he wasn't going to be able to get all four corners secure, or a flush mount of the HSF for cooling. A quick call to VM and they replied they would send out a new cooler this morning. I have to admit..I called around a bit to see if anyone had one locally, and even looked long and hard at a Zalman 9700, but I've read differing reviews on whether or not it would fit without mods - and some of the capacitators on this board are so close that I decided to hold off. Hopefully installation of the new HSF will go smoothly and I'll see some decent reads from Core Temp when it is all said and done.
 
You need a voodoo doctor to come to your house and get rid of the evil juju that is living inside your computer.

Man, what lousy luck. Good news is the great work from VM.

I have just put together a system much like yours. My ArcticCooling Freezer Pro 7 keeps my e6700 cool as a cucumber. Around 35-37 degrees.

Sounds like VM is on the job. :D
 
...than anything...and a disappointment. I KNOW I have an essentially great PC, just can't quite seem to get it just right yet. And, at least for me, the big difference between buying a rig like this and buying something off the shelf is the learning curve I've imposed on myself. Before, I'd read system reviews, make a choice, and buy a PC and never look back. When it came time to "do it right" - buy a PC with the components I wanted - I did a LOT of research on individual components, on boutique vendors, etc.; AND started to learn about all of the little tweaks/concerns/tell-tale system signs of a PC that is running optimally. My personality is addictive by nature...once I get my head wrapped around something, I tend to pursue it until I have comfortably mastered it and/or driven the people around me crazy...it's the way I learn, and it's a curse and a blessing. I AM learning a lot, and confirming a lot of what I already knew; and Heather, from VM is a saint in my book (she probably is rueing the day an e-mail from me first crossed my desk, but she is SO on top of things..and incredibly helpful). I'm also impressed with the folks that operate HardOCP's forums; everyone I've had a post from from here is incredibly helpful, knowledgeable, insightful, and, for the better part, patient as hell; not always something you find on a board like this. My ramble for the day...can't wait to get this beast up and running again though!
 
...For being so patient. Getting emails from you is never, ever a bother. I welcome the chance to talk with you. Your heatsink is on the way--I've just sent you a tracking number.
 
...like I said, if there is frustration it's a "general" frustration about not being able to use the PC right now, not with Velocity Micro or your support. Things can happen in transit, parts do occasionally fail; nobody likes it, but it's a fact of life. Hopefully once the new heatsink arrives everything will once more be fine.

Have a good one, Heather. ;)
 
AC Freezer Pro 7 arrived today...retail box, nice bit of thermal paste applied at the factory, took just a few minutes to install, and I'm getting the temps now I would expect. Starts off at about 32C when I first boot, levels off at about 37C at idle; a good 18C cooler than before. Haven't really stressed it under load yet, but would expect it to be mid to high 40s given the temp at idle.

Thanks, Velocity Micro and thanks, Heather!
 
coachjohn said:
AC Freezer Pro 7 arrived today...retail box, nice bit of thermal paste applied at the factory, took just a few minutes to install, and I'm getting the temps now I would expect. Starts off at about 32C when I first boot, levels off at about 37C at idle; a good 18C cooler than before. Haven't really stressed it under load yet, but would expect it to be mid to high 40s given the temp at idle.

Thanks, Velocity Micro and thanks, Heather!

That's much more like it and in line with our Core 2 testing. Glad to see everything's 100%. That 680i board reports temperatures very well in the BIOS, and NVIDIA's monitor will report almost 10c higher, FYI.
 
...but I am curious...how accurate is NVIDIA's monitor on fan rpm? And should I have SmartFan enable in BIOS?

Thanks Chris..keep up the good work.
 
coachjohn said:
...but I am curious...how accurate is NVIDIA's monitor on fan rpm? And should I have SmartFan enable in BIOS?

Thanks Chris..keep up the good work.

You shouldn't have to worry about any fan throttling settings with that Arctic Cooling unit. It's very quiet to begin with.

As to NVIDIA's accuracy in their software, you can always check it against the BIOS and see if there's a discrepency...
 
I did a couple of quick checks...SpeedFan and the BIOS on the eVGA 680i board read the same for the fan speed...NVIDIA's monitor reads it WILDLY high. With SMARTFAN on in the BIOS the fan was spinning at about 980 rpm with fluctuations (the "smart" control)...I set it to manual and 80% and now the fan is a constant 2200 rpm in both, and my temps have settled even lower..and I don't see the constant rise and fall of a few degrees C, either...a constant 32-33C at idle. Now..in your opinion...2200 rpm too high (AC rates the HSF at a max of 2500 rpm) for fan longevity?

Chris, I can't say enough good about VM. I've already recommended a parent to VM for a laptop (they ordered yesterday) and a member of our administration - good, good company.
 
....I wonder what percentage of eVGA 680i boards are flaky....and how vendors using them are going to respond in the long haul. I'm going to run mine through the mill this weekend....with any luck, I'll have one of the boards that exhibits nothing but stable behavior. A shame that so many seem to be having issues...it has all the makings of a dynamite board.
 
It is a dynamite board, and we are not seeing SATA issues with it. We have sold a ton of these boards and - with the qualified configurations that we are selling - we have not had problems in the validation (R&D) of the board, the production of the units, or customer complaints in the field. But believe me, I was on the phone with NVIDIA today to be kept up to speed in case there's anything we should be aware of. And that's not to discount the fact that many people do seem to be having issues with the particular configurations they may have purchased on their own. And barring that, it seems that some people have had success when they switch to another board, even if it's the same vendor. So that's anybody's guess.

Regardless, if there are any problems with your system, you can be sure we'll take care of it.
 
....given my history to date with Velocity, I feel pretty safe that if I DO end up having an issue it will be quickly rectified. My comment on "how vendors using (the boards) are going to respond in the long haul" is more of an open-ended question...I can't IMAGINE being a vendor that has sold a ton of these boards and now realizing that there MAY be a real issue with them - or at least some of them. It's a potential PR nightmare for NVIDIA, for eVGA, for ASUS, etc. - let alone all the builders out there relying on them. Dan made the comment that, "While the problems with the 680i are very real, I'd imagine that the bulk of the problems are isolated to a small percentage of boards sold and that people like me who have experienced problems are in the minority." One of the questions for me, though, is what about long term problems..boards that work well initially but experience problems later down the road? I'll follow these threads..and NVIDIA's and eVGA's responses....pretty close and see how it goes...and give my system a thorough workout this weekend with Photoshop CS2...and, if I have a question or observation worthwhile I'll post here and maybe we can help each other.

Take care, Chris.
 
coachjohn said:
.......I can't IMAGINE being a vendor that has sold a ton of these boards and now realizing that there MAY be a real issue with them - or at least some of them. It's a potential PR nightmare for NVIDIA, for eVGA, for ASUS, etc. - let alone all the builders out there relying on them. Dan made the comment that, "While the problems with the 680i are very real, I'd imagine that the bulk of the problems are isolated to a small percentage of boards sold and that people like me who have experienced problems are in the minority." One of the questions for me, though, is what about long term problems..boards that work well initially but experience problems later down the road? I'll follow these threads..and NVIDIA's and eVGA's responses....pretty close and see how it goes...and give my system a thorough workout this weekend with Photoshop CS2...and, if I have a question or observation worthwhile I'll post here and maybe we can help each other.

Take care, Chris.

Whoaaaa.... what is this issue with the Nvidia 680i mobos your refering to??

VM just shipped my PC today (eVGA 680i mobo )...so now Im a little concerned :eek:

EDIT: Nevermind found the [H]ard article on this..... looks like I cross my fingers and HOPE I dont have one of those flaky chipsets :rolleyes:
 
FAAmecanic said:
Whoaaaa.... what is this issue with the Nvidia 680i mobos your refering to??

VM just shipped my PC today (eVGA 680i mobo )...so now Im a little concerned :eek:

EDIT: Nevermind found the [H]ard article on this..... looks like I cross my fingers and HOPE I dont have one of those flaky chipsets :rolleyes:

We've fully tested our configurations and numerous systems have gone through production and we have not seen this issue. HOWEVER, it DOES seem that there is an issue that people are experiencing with certain configurations. If we had come across this on our configs then perhaps I'd have more information for you, but all I can tell you is that we have a very close relationship with EVGA and NVIDIA and if there's something we need to know about, we'll get it taken care of. ;)

It should be noted that, from what I've heard from 3rd parties, it crops up in some pretty extreme configurations. However, our "extreme" and overclocked system, the Raptor Signature Edition, has an add-in hardware RAID controller as I have found it to be much higher performing. So, we may have avoided this situation altogether by pure coincidence.
 
...a) because he's much more knowledgable than I am on the subject, and b) because to date (very short time frame, admittedly) I haven't had any problems with my board. I have three SATA drives on mine (Raptor 150GB and two WD 250GB), none of them in RAID...no issues yet. I'll be on the PC a good bit this weekend...going to do a photo shoot in the morning, so I'll be processing RAW images, doing some work on them in Photoshop CS2, possibly some printing on an Epson 2200 using QImage...and I hope to get in a round or two of Madden, so I should have some idea of the stabilty of the rig by then. You can't go wrong with the customer support at VM...rest easy, and enjoy that new machine!

John
 
....the eVGA board...should I register it with eVGA? Or, as a board in a build by VM is this not necessary/recommended? I guess that would hold true for all of the components...1 year warranty through VM, lifetime warranty on eVGA products...once the year is up from VM, if I'm registered with eVGA...see what I mean?

John
 
Sure, register the components with the original manufacturers if they have longer warranties, such as EVGA. That's precisely the reason we use retail boxed parts in some cases and include the documentation.
 
My VM Campus Edition was delivered in mid - Oct. I love the machine - the attention to detail is amazing. However, from the outset, my AC freezer 7 has been disinclined to spool up (300 - 500rpm max bios reading) in the face of escalating core temp readings - resulting in temps that are somewhat high, but not necessarily alarming under 100% load in Intel TAT (39-41degC idle; 65-70degC 100% load).

VM (most especially Ms. Taylor) have made Herculean efforts in an attempt to rectify this seeming anomaly. Freezer 7 and DP965LT MB both replaced on site, ultimately the machine was returned to Richmond for repair.

Upon its return, the machine looks beautiful, temps are down slightly. But the CPU fan anomaly still persists. Even under TAT full load, Freezer 7 speed never surpasses ~500 rpm.

Although I am admittedly a novice, alteration of any or all settings in intel's most current BIOS will stop this throttling. Noise is not a real concern for me. I would prefer the fan operate constantly in the 2000rpm range (as VM's tech support indicated their mule's Freezer 7's typically do).

Any thoughts
 
Back
Top