Copper sealent on the freshly cleaned blocks?

Tech-Daddy

Gawd
Joined
Jul 28, 2004
Messages
514
I have read from forum to forum about various ways of cleaning my blocks. I just purchased a used set of NV78's for use in my first water cooling attempt.

The blocks are in need of a good cleaning... lots of corrosion and gunk inside the blocks.

Since they are out of warranty, the blocks will get pulled apart and the copper cleaned. Still deciding on the toothbrush/ketchup method or another possible route. But... what I am seeing is that people who clean their parts start experiencing oxidation after about 6 months.

Has anyone tried a copper sealent on these blocks to stop the oxidation after you have cleaned up the copper? I know you would not want that chemical in the loop, but I'm referring to the areas outside of the water path.

Anyone who knows me knows that I like to dress up and detail my systems, and after reading what everyone has been complaining about, I'm trying to take preventative steps to keep those issues from happening.


Thoughts?
 
clear nail polish

oh and the ketchup thing, ketchup contains vinegar, do yourself a favor and just go with vinegar, hella less messy and cheaper.
 
Ketchup, Vinegar, a good toothbrush and you'll be good to go. Make sure you do a clean flush with distilled water afterwards.

Looks like someone was running some alu in the same loop if the corrosion is that evident. Make sure you don't do the same.
 
Ketchup, Vinegar, a good toothbrush and you'll be good to go. Make sure you do a clean flush with distilled water afterwards.

Looks like someone was running some alu in the same loop if the corrosion is that evident. Make sure you don't do the same.

Actually, the inside of my copper block gets really nasty too... And I run straight copper/brass.

I don't think the OP meant corrosion, but oxidization.
 
I will post up some pics tonight, but it looked nasty. Not just the patina from the green copper oxidation, but (what looked like to me) almost a gunk, maybe a mold, that had nested itself into this block.

I dunno... but I'll let the pics to the talking later when I get home.

On the vinegar as a cleanser... is that full strength? or watered down to some ratio? I can see me putting that in a bucket, with a toothbrush... and a breathing respirator... ;) (if the vinegar is diluted, I'll bet that is why ketchup was recommended. That plus the acidic content of the tomatoes likely works well, and smells better to boot!)

thanks for all the input guys! Much appreciated!
 
As I stated previously... here are some pics of what I am getting ready to clean tonight...
back1.jpg


back2.jpg


front1.jpg


front1.jpg


and it does look fuzzy in there... kinda like mold. not sure.

Do those seals look overly compressed?
 
Yeesh,...

What's your coolant mix?

Have any aluminum in the loop?

use pure vinegar to clean.
 
That's OK, I had to re-read it twice to find it myself. I'd swore that was the case then wanted to make sure before pointing it out to you, damn near couldn't find it after that.:eek:
 
yeah....
nada clue. :confused:

All I know is these things looked like a$$... 2 rounds with ketchup, 3rd round with straight vinegar. Distilled water final rinse, and they are starting to look better.

But what really has my panties in a wad was the epoxy on one of hte lower screws, that I am assuming was used to seal a screw. Unfortunately... whomever put it on got some in the actual screw head, so I had to use my micro driver "stripped screw removers" in order to get enough traction to remove it....

The seals were trashed as well...

SO

Now I have 2 sets of seals, a screw, possibly a lower acrylic piece... all of that I will contact DD tomorrow for and see if they have a way of getting any of that for me. I Was told by one of the DD forum admins to contact a specific person at DD tomorrow and explain the situation, and that I should be able to get the replacement seals. I'm assuming that the screw should not be an issue through them... I am concerned about the acrylic though.

We'll see....:rolleyes:
 
For seals you might check an auto parts store for an o-ring of the proper diameter (after the seal is pulled into a circle) since all they are is o-rings.
 
For seals you might check an auto parts store for an o-ring of the proper diameter (after the seal is pulled into a circle) since all they are is o-rings.

It's a good thought, but after pulling these seals tonight... I doubt *very seriously* that I could shape a round seal into "that" shape! ;)

I'm pretty sure the seals are cut in that shape.

I did a little more work on the acrylic tops, and got them a bit better... but I need to find something that will really clean this block... there is some really aged stuff down in the copper of this block.

Pooor wittle bwock was awwlll abused......
;)
 
Trust me, they're standard o-rings. You should try putting the o-ring back in the Swiftech MCW Ramcool. Talk about coming up with creative curse words...
 
if you cant find any O Rings that will fit, try something called The Right Stuff gasket maker. its like silicone caulk except much better. it will seal anything, is chemical and heat resistant, easy to use and is like $5 a tube. you can find it at most auto parts stores, we used this stuff all the time at the garage i worked at. one trick with this stuff is when you put it on, squirt it in the channel where the old seal was. put the top of the block back on, but dont screw it down very much. just enough so that it seals all the way around. once it dries for a few hours, then go and crank down the screws. this way it wont just ooze out all over and will stand up to more pressure.
 
JERM-
I called DD today and spoke with a most helpful Debbi, and setup an order for a "refurb kit" for these NV78's. new tops/back acrylic pieces, new seals and new screws. Very helpful.

Now, I did a bit of research, and the use of ketchup or taco sauce to clean the copper was narrowed down to the 2 components, vinegar and salt.

So, after I did my initial 3 rounds of cleaning last night using ketchup, tonight I upped it using the vinegar/salt mixture.

Here are the reults:

Initial teardown:
during1.jpg

during2.jpg

during3.jpg


Then after 2 rounds with ketchup, and one round with ketchup and vinegar:

during4.jpg

during5.jpg

during6.jpg


then tonight I hit it with the vinegar/salt mixture. Only left it on the copper for a little over two minutes.

during7.jpg

during8.jpg

during9.jpg


Keep the distilled water nearby, because this mixture can cause discoloration if left too long. I had to do some quick rinsing, and toothbrush scrubbing and then immediate rinsing to get rid of some of the accidents...

but as you can see, they are coming along!

Next steps will be some sort of copper polish that will bring that bright copper finish back!
 
If you'll read the OP he bought them used so I doubt he has much idea what was used in the loop.


I think I just found it in another thread where the person that I purchased these from almost broke my heart....

"I am running the Home depot 1/2"ID - 3/4" OD and it works great !! Using Fluid XP+ EXT (blue)"

they are referring to Home depot tubing vs tygon/masterkleer/swiftec tubing.

*IF* that is what they were running through these blocks... I know what *not* to use! ;)
 
;)
during10.jpg


and a closeup shot:
during10a.jpg


After cleaning 4 rounds with the ketchup, and vinegar/salt combo, and realizing that some of this gunk just was not going to come out, I went to town on it with some Tarn-x,cotton balls and q-tips, and a bucket of distilled water that I would rinse off in every 30 seconds to a minute.

Also figured something out. When you remove the acrylics on the top, and you are looking for something to get all of the residue of the previous seals off, as well as remove the liquid scaling or marking of the water channel, I found some Lexan polish at Home Depot the other day. That plus a clean, lint free cloth... got me this in less than 2 minutes....

during11.jpg


during12.jpg


Hope this helps some of you!
 
scarry what you can do in your own kitchen that the pros cannot seem to accomplish at the factory. Excellent work with the polish... if only I had the time to polish my parts.
 
:eek:
*blushes*

Thanks guys! Knowing what I know now, I could have likely performed all of this in about 2 hours... but hind sight is 20/20 on something like this, and you learn as you go!
;)

To sum up...

ketchup/taco sauce - decent performance on heavily scared copper surfaces. Lots of scrubbing, lots of waiting.

vinegar+salt - *must be very careful*, if you leave it on too long (like I did on one spot) it will scar the copper surface with a discoloration that is a PITA to get out! Decent cleaning performance.

Tarn-x - using this requires good heavy rubber gloves, a lot of cotton balls and q-tips. I also used a small, stiff bristled paint brush (much like you would use painting oils on a canvas) that was maybe 1/4 inch wide, and had bristles that were less than 1" long. This allowed me to take the bristles while using the Tarn-x and jab them down on top of the curved heat fins over the GPU. This scrubbing motion, in conjunction with the Tarn-x allowed for the removal of the crap around the base of these fins, as well as the sides of these fins. Key here is that the Tarn-x is very caustic. I did the work in my garage, using a garage sink. I had a small bucket of distilled water to the side, and would work on the pieces with cotton balls/q-tips/small brushes for *no longer than* 1 minute. Then I would pour out (into the sink) the little bit of liquid Tarn-x in the block channels, and then soak the block in the distilled water to rinse. I did this every minute while cleaning (to keep the Tarn-x from standing on the surface and accidentally overexposing a copper surface).

I"m pretty happy with the results too! ;)

Thanks to everyone that offered up suggestions, and big time thank you to all the people that posted up their "How to's:" on block cleaning. Those plus Google allowed for the results you see here.

:D
 
Back
Top