Computer Freezes on Win 7 Splash Logo

chronicfx

Limp Gawd
Joined
Mar 29, 2012
Messages
286
Hi all. I put together the system in my sig below on the day Ivy Bridge was released. This is all within a HAF 932 case and it has worked beautifully. I decided a new computer should have a new look, so the other day I changed out all three 200mm fans on my Haf 932 for blue LED 200mm fans, and changed nothing else except they were originally on fan headers but now I put them to the PSU. After replacing the three large fans I powered up my system and it froze for the first time ever, I was puzzled.. I now figured out it is my ESata drive when plugged into my rear Esata port that is causing the freezing. It boots fine without the drive attached, the esata port HDD can then be hotplugged while the computer is on and all folders/pictures can be accessed, drive checks out normal with crystaldiskmark, but I reset and it freezes again, until I remove the ESATA drive and boot..

My question is, what can cause this? I only changed the fans. Also for 2-3 months my system was booting fine with the ESATA HDD attached 24/7, now I must remove it to get into windows. I am planning to re-install the Sata and Asmedia drivers when I get home, do you feel this will solve the problem?
 
Somewhat related questions:

1) can you confirm that hotswap works using eSATA the ASMedia 1061 ports with your setup? In that you can boot into Windows with your eSATA powered off, then turn it on in Windows and the drives are recognized?
2) what eSATA device are you using, does it have just one drive or two?
3) Can you configure the ASMedia SATA ports in your UEFI/BIOS? E.g. are there options to enable/disable hotswap, IDE/AHCI etc. for those ports on your ASRock board?

The reason I ask is that my Asus P8Z77-V Pro also uses the ASMedia 1061 controller for 2 extra SATA3 ports (no eSATA on back I/O), so I am using an eSATA to SATA bracket to connect to my external 2-bay enclosure. Hotswap does not work for me, I have to boot with the enclosure on or the drives will not show up in Windows. Haven't been able to get Asus to give a good answer on the problem, as I think it might be a UEFI issue.

Thanks!
 
Somewhat related questions:

1) can you confirm that hotswap works using eSATA the ASMedia 1061 ports with your setup? In that you can boot into Windows with your eSATA powered off, then turn it on in Windows and the drives are recognized?
2) what eSATA device are you using, does it have just one drive or two?
3) Can you configure the ASMedia SATA ports in your UEFI/BIOS? E.g. are there options to enable/disable hotswap, IDE/AHCI etc. for those ports on your ASRock board?

The reason I ask is that my Asus P8Z77-V Pro also uses the ASMedia 1061 controller for 2 extra SATA3 ports (no eSATA on back I/O), so I am using an eSATA to SATA bracket to connect to my external 2-bay enclosure. Hotswap does not work for me, I have to boot with the enclosure on or the drives will not show up in Windows. Haven't been able to get Asus to give a good answer on the problem, as I think it might be a UEFI issue.

Thanks!

1) Yeah it works. I plug in the drive and its recognized in about 5 to 10 secs.

2) Iomega 2TB professional esata external drive

3)... lemme reboot lol
 
It says ASMEDIA Sata 3 controller Enable/Disable. Didn't see anything about hot swapping enable disable. AHCI/IDE modes are available for asmedia ports. Where each individual drive is listed it does ask if it is internal or external drive. That could be for hotswap but I am really not so knowledgeable with hard drive settings and RAID and all that.
 
AHCI/IDE modes are available for asmedia ports.
Your controller does support Hotswap.

Unfortunately I have no idea why changing the fans would have created a problem.
 
It says ASMEDIA Sata 3 controller Enable/Disable. Didn't see anything about hot swapping enable disable. AHCI/IDE modes are available for asmedia ports. Where each individual drive is listed it does ask if it is internal or external drive. That could be for hotswap but I am really not so knowledgeable with hard drive settings and RAID and all that.

Thanks man. On my Asus P8Z77-V Pro (with the same ASMedia SATA6 controller), I cannot configure the ASMedia ports as AHCI/IDE, I can only enable/disable the controller. Good to know.
 
Back
Top