CMOS checksum error

that guy is screwing you.. it means its time to buy a new machine
























no it means some settings are incorrect (IE cpu is a 2.0GHZ you are telling the bios that it is a 4.0GHz)
 
OMFG YOU FUCKING SCARED ME

so um how do i fix that because I cant really get back into the bios to change anything, it set everything back at default
 
well the way to reset it is to clear all bios settings and go to default, there is a jumper on your mobo (usually near your bios chip or the battery) you switch the jumper to the other pin wait about 10 seconds, switch it back, power on your pc
 
I know how to clear my cmos but thanks :D I was just wondering why it did that!


So I clear my cmos. Hit the power button, it powers on, then turns off right after. Then turns back on and I change my bios stuff. Then it turns off with a black screen so I have to clear te cmos again. Then it says CMOS checksum error.

I think its the powersupply. 2 delta 50cfm fans plus thermaltake smartfan 2, and a fan controller ontop of all the other things.

What do you think?
 
When I clear the BIOS I get that too, but my computer won't restart, it just waits for me to change BIOS settings. Are you clearing the CMOS with the power cable unplugged? That could do things...
 
um ya. well i made this thread in the hardware section and they said i should reflash my bios.
 
this is what i did too.. you get the check sum error, hit reset, get it again, hit reset, get it again, hit reset, computer boots up with safemode settings (at least for my kt7 anyway)
 
You need to reflash your BIOS. If you continue to get errors, something died in your BIOS chip, or on your board, and you need to RMA it, or get a new one. :(

Some boards have dual BIOS chips. When they refuse to boot, then you're SOL. ;)

Well, you might have a bad sound card or video card on your machine. You might try swapping those, along with RAM, but this sounds more like a BIOS problem than anything else. Never hurts to try though. :)
 
Memory problems or CPU issues could be your problem. More than likely memory. PSU problems won't usually if at all result in the symptoms that you have described. I would check your memory, reflash your BIOS and go from there.

Clearing the CMOS with the system unplugged is fine. Just don't clear the CMOS with the system power on. That WILL do things.
 
You might have a coin-cell battery that is no longer providing enough juice to keep your CMOS pages from corrupting.. I'd pull the coin cell out and go get another one (probably a CR2032). In addition, make sure that the CMOS jumper is in the right place. If it's on the wrong set of pins, you'll get this error over and over and over since the BIOS is clearing CMOS when it sees the jumper installed.
 
Originally posted by PurduEE
You might have a coin-cell battery that is no longer providing enough juice to keep your CMOS pages from corrupting.. I'd pull the coin cell out and go get another one (probably a CR2032). In addition, make sure that the CMOS jumper is in the right place. If it's on the wrong set of pins, you'll get this error over and over and over since the BIOS is clearing CMOS when it sees the jumper installed.

If the CMOS jumper is in the 'Clear CMOS' setting, the board will simply not boot. That's experience, some boards might try booting?
 
Originally posted by ’m‚³‚ñ
If the CMOS jumper is in the 'Clear CMOS' setting, the board will simply not boot. That's experience, some boards might try booting?

Depends on how the BIOS is coded. Some do, some don't.

On some BIOSes, the code is written to check for the presence of the jumper during POST. If it finds the jumper, it will mark the CMOS checksum bit, indicating a bad checksum, and then complete the boot. Others won't. It's still worth checking on the chance that he has a board that has the behavior I described rather than the behavior you described. Might as well 'leave no stone unturned'.

To be honest, there are very little absolutes when dealing with different motherboards and BIOSes. There's no guarantee that they are all going to work the same way, and in point of fact, most of the time they don't.
 
Originally posted by PurduEE
Depends on how the BIOS is coded. Some do, some don't.

On some BIOSes, the code is written to check for the presence of the jumper during POST. If it finds the jumper, it will mark the CMOS checksum bit, indicating a bad checksum, and then complete the boot. Others won't. It's still worth checking on the chance that he has a board that has the behavior I described rather than the behavior you described. Might as well 'leave no stone unturned'.

To be honest, there are very little absolutes when dealing with different motherboards and BIOSes. There's no guarantee that they are all going to work the same way, and in point of fact, most of the time they don't.

I suppose that's the truth. I've never had experience with anything else, so really. :p

BTW, the last two sentances you said there have bitten me in the ass so many times it's not funny.
 
Back
Top