CMOS Check Sum Error / CPU unworkable

themolt

Limp Gawd
Joined
May 7, 2003
Messages
261
I just bought a new ABIT NF7-s v2 and AMD XP Barton Mobile 2600+ and installed everything. Thermalright heatsink on top. Everything fit perfectly and the cpu fit in the socket just fine.

CPU: AMD XP Mobile 2600+ (Barton)
MOBO: ABIT NF7-S v2
RAM: Micron PC2700 (DDR333)
I booted up and the bios loaded and it says

"Main Processor: Unknown CPU Type (600MHz)
Memory Testing: 524288K (Ok)

Memory Frequency for DDR333
DDR Dual Channel Enabled
Primary Master: xxx
Primary Slave: none
Secondary Master: xxx
Secondar Slave: none

CMOS Checksum Error - Defaults Loaded"

Then I clicked F1 to see what would happen and it did some test and said..

"NTLDR Missing"

Then i rebooted and it said

"Same as above and..
CPU is unworkable -Check Softmenu"


Can someone help me?
 
Sounds like you need a BIOS update to me. The unknown CPU type hints at the motherboard not knowing what type of CPU you have. This is not surpising with a mobile chip.
 
how do i update the bios without an os or anything. all i can get to is the bios settings. can you please help me. this is my first computer i've built by myself

Update:
I was using a brand new reformatted HD when i tried that.

I used another HD with an OS installed on it and it loaded all the way to the Windows XP in safe mode only. I installed a few drivers but that didn't fix much. I tried to install flashmenu but it wouldn't load.
 
Go to the MFG website and get the latest BIOS. You will need to make a Win98 boot disk and have a floppy drive attached. There will be full instructions on how to flash the BIOS.
 
Reset the CMOS by using the jumper on the motherboard. Then reboot. It should work.

Novensu
 
I belive there is a setting on the NF2 boards about "cpu error hold" or something to that effect if the cpu isn't running at its designated speed. Maybe that would help
 
thanks for all the help. someone on abit-usa.com forums helped me out a little more. if anyone else is having this problem then here's one solution:

1) best to load fail-safe and optimal settings in bios.
2) use a reformatted hd, and set the 1st boot device to cd-rom.
3) install winxp.
4) update bios using flashmenu
5) it will reset your cmos so you need to go back and change fail-safe and optimal settings

this should help some.

anyone other questions you can email or pm me. plus i have a lot of info on what i did at my website
 
themolt said:
I just bought a new ABIT NF7-s v2 and AMD XP Barton Mobile 2600+ and installed everything. Thermalright heatsink on top. Everything fit perfectly and the cpu fit in the socket just fine.

CPU: AMD XP Mobile 2600+ (Barton)
MOBO: ABIT NF7-S v2
RAM: Micron PC2700 (DDR333)
I booted up and the bios loaded and it says

"Main Processor: Unknown CPU Type (600MHz)
Memory Testing: 524288K (Ok)

Memory Frequency for DDR333
DDR Dual Channel Enabled
Primary Master: xxx
Primary Slave: none
Secondary Master: xxx
Secondar Slave: none

CMOS Checksum Error - Defaults Loaded"

Then I clicked F1 to see what would happen and it did some test and said..

"NTLDR Missing"

Then i rebooted and it said

"Same as above and..
CPU is unworkable -Check Softmenu"


Can someone help me?


Pretty normal for the board to not recognize a mobile...Only the DFI lanparty boards "officially" recognize a mobile for what it is.

You need to manually configure the multiplier and FSB in the bios..

MD
 
Back
Top