build computer shuts down after 30 secs( UPDATE )

xrAzVaNx

n00b
Joined
Dec 14, 2004
Messages
51
Hello guys,
today I finally had time and my friend came over to help me
We installed a newer power supply(ANTEC NEOPOWER 480W)
and we removed the thermal paste that came with the processor and applied new one..
The problem has been fixed !
Heres the temperatures in the BIOS:
CPU: 57degrees(still high)
MB: 28 degrees


Now, we ran fdisk with my old win98 boot disk and we made a primary partion and an extended partition..
It only recognized that I had 23 GB of total space on my Hard drive, but I have 160GB!! Anyhow, I still went on and made my primary partiion 18gb( C:/) and I made my extended partition (D:/) 5GB..
After, I formatted the two of them..

Then, I booted up with my WIN XPpro CD and after it finished loading all files it said:
STOP
INACESSIBLE_BOOT_DEVICE 0x0000007B (OxF20603848, 0xC0000034, 0x00000000, 0x00000000)
..Check for viruses,.. remove any new installed harddrives or harddrive controllers,...check your hardrive to make sure it is properly configurated and terminated. Run CHKDSK /F to check for hardrive corruption, and then restart your computer...

I tryed to boot up with my WIN 2Kpro CD and it was the same thing.. I ran scandisk and it found no error..

What to do?

EDIT:I tryed putting my specs into my signature but it doesnt seem to work so here it is:
Intel 3.2 ghz 1mb cache, 800FSB LGA775
ASUS P5GD1
2x 512MB DDR400 RAM
Ati Radeon x700 pro
Western Digital 160gb
1.44Mb Floppy
SoundBlaster Audigy 2 Value
ANTEC NEOPOWER 480W
NEC DVD RW+- Dual Layer
 
sounds like a crappy motherboard, try rmaing it.
frown.gif
 
No, it mustnt be my MB... it must be somethign with my HD..
I did some research on internet and I found this:

Stop 0x0000007B or INACCESSIBLE_BOOT_DEVICE - This message indicates that Windows has lost access to the system partition or boot sector during the bootup process, an incorrect device driver was installed for some storage adapter, hard drive or other type of drive that you are booting to. It also could be that possible a virus has infected the boot sector of the hard drive.

Edit: Ok checked all conections, its connected to the primary IDE on my MB, and pin 1 is aligned correctly, also, in BIOS its set as primary IDE so no problem there..
Booted with a diagnostic utility from the manufacturer, no errors found.

Also,before it starts loading the files for winXPpro setup it says: Could not open the boot partition to check for a signature
???
 
I'd bet your problem is formatting with the 98 boot disk. Boot from your XP CD, preferably with Serivce Pack 2 slipstreamed into it (I'm not going to post how to do that, Google for it if you don't know how and don't have it already), and use the Windows XP Setup program to delete all of the partitions on the disk. Then create a partition on the disk, once again using the XP setup CD, and format with NTFS. Don't forget that XP Pre SP1 doesn't support disks larger than 137GB (128GB in binary, 48 bit LBA), and that 98 Boot disk has the same limitation - when it runs over the 28-bit LBA maximum of 128GB, it starts counting again at zero :eek: ! So it will put the boot sector and partition information in a part of the disk where XP won't look for it, hence inaccessible boot device. You don't need a 98 bootdisk to install XP, and you won't be able to read NTFS volumes with a 98 boot disk anyway. Let Windows XP do things its way, XP is much better than 98.

EDIT: Added Eek! for emphasis at the prospect of starting back at zero after overflowing 28 bit LBA.
 
What filesystem did you format the partitions with? Also why not just use the XP Pro CD to format everything nice and easy in NFTS. Boot off the cd, select the option to choose which partition you want to install XP on, then delete the two existing partitions and repartition the drive. If you like you only have to create the OS partition and then you can use Computer Management in the admin tools to create the rest after windows is installed.
 
The file system created by FDISK with the win98 cd is FAT32, but the thing is
when i boot with the winXPpro cd it doesnt show any options, it just starts loading files for the setup and at the end it displays the error reported earlier..
 
Are you using an actual XP Pro CD, or a restore disk? Because it should bring you to the blue setup screen, and ask you to partition, etc.
 
I made a special disk to update some drivers for my IDE RAID driver from my MB support cd and when the setup prompted me to press F6 i did and then i installed it, and then the setup continued , and at the end of the setup, NO MESSAGES :D. it asked me if i wanted to partition ect.. so im formating the partition using NTFS right now

Oh and im doing it with the win2kpro CD coz the winXPpro wouldnt work..
Now its all going very slow so ill keep u updated after its done
thanks
 
hey i got it up and running even tho' it recognizes only 130GB of my 160GB hardrive..
but i have to say thank you to all the people that helped me from the beggining, especially in my first thread !
Thanks Guys! :D
 
Back
Top