BIOS update

speedlever

Limp Gawd
Joined
Sep 29, 2006
Messages
447
Due to a HD crash, I had to replace the drive and reinstall W7/64. I decided to update the BIOS and did so, but got some kind of error msg about OC. It's been so long since I did the initial setup, I don't recall having any OC'ing. IAC, after the reboot, the new BIOS version shows up and everything seems to work ok... except, I can't see my external esata drive.

I have two controllers with the yellow flag and don't know how to fix it. When I search for updates it tells me the best driver is already installed.

I think these may be the issue with my esata drive.
U8Fd9.png


As part of my rebuilding process, I replaced the failed HD with a SSD. I made sure that in the Asus P5B-E BIOS I have :
Main: IDE config set to config SATA as AHCI
Advanced: JMicron sata controller mode set to AHCI

Does this look right?

Should I try to reinstall the BIOS and see if that clears up the controller issue? But being the same revision, I don't think it will let me update it.

Suggestions?

Note: thinking that Win7 had the correct chipset drivers, I didn't install them until after I'd installed Win7, the graphics drivers, and the BIOS update. Now my chipset drivers check as the latest. Before installing them, I could not figure out how to check the chipset version (using regedit). After installing them, regedit showed the version info.
 
I'd install the drivers straight from Asus for your board - chipset, disk controllers, audio, etc. Windows will install generic drivers that a lot of times work, but are less than ideal - in my experiences anyway.
 
A couple of things...

1) Asus only has the 9.1.1.1019 INF update, but Intel has a later one: 9.1.1.1025 for the P965 chipset. Also, Asus does not reference Win7 but Intel does. FWIW.
2) I have been having some bugcheck reboots since I: swapped around the RAM, upgraded the BIOS, and uploaded the 1025 chipset drivers.
3) my external esata drive doesn't show up. I think I now know what I'm missing with those two yellow alerts. Not sure yet how to fix it either.

I think I'm going to reset the mobo to defaults, make sure the drives are setup in order (BIOS default settings mess it up), and re-install the BIOS. Then reboot and tweak the BIOS a bit (no OC'ing) just set the drives correctly, and:
Leave SPD enabled. Configure sata as AHCI,
Set JMicron sata controller mode to AHCI
Set the mem freq at DDR2-800 for my PC2-6400 RAM,
PCI Express freq locked at 100, PCI clock sync mode at 33.33MHz.
I think I"ll leave the voltages on auto.

Let's see how this works.
 
Update: I set the BIOS to default and reloaded the 1807 BIOS for my P5B-E. Everything went smoothly and no errors.

However, I still have those two channels with the yellow alert and I am unable to connect to my external esata drive.

I made a change to the BIOS that I had not done before: under Advanced I changed the JMicron sata controller from IDE to AHCI.

I had been running BIOS 1704 with IDE config: configure sata as AHCI.

Should I have left the JMicron controller sata controller set to IDE? Could that have caused my yellow alerts (assuming that's what causing my esata external drive issue)?

One other thing I should probably do is complete the installation of the mobo drivers from the Asus site. Maybe I'm missing something there that would fix the esata drive.
 
You need to load the drivers for your JMicron 363 controller.

Here's the driver download page.

Read the release note and get the latest driver.
 
I solved the problem with my external esata drive and the two yellow alerts on the ATA channels.

What I did was select one of the faulty channels and have it update the driver by searching my C drive. It found the driver it needed and that fixed the problem.

Wish they were all this easy!
 
I solved the problem with my external esata drive and the two yellow alerts on the ATA channels.

What I did was select one of the faulty channels and have it update the driver by searching my C drive. It found the driver it needed and that fixed the problem.

Wish they were all this easy!

Yep, driver wasn't loaded.

You should update it at the page I linked.
 
Do I need both drivers or just the esata driver?

How can I know what JMicron driver version I currently have?
 
One other question: How can I determine what this device is? I haven't found anything not working yet... but I'm sure I'll stumble across is someday.
Update driver doesn't do anything.

yOUwX.png
 
Fixed.

I used IE and searched for Windows updates and it found the driver I needed for this.
 
Back
Top