ASUS A8V & 12v line

Impulse

[H]F Junkie
Joined
Apr 5, 2001
Messages
10,232
Simple question here (but one that's a little hard to answer via a search), what's your 12v line at usually on your ASUS A8V as reported by the ASUS PC Probe? On mine it's been reporting 11.491 - 11.551 since I installed it, whether it be at stock speeds or at the current 2.3GHz. Rest of my system info is in the sig.

The other two lines are always looking healthier according to PC Probe (5v at 5.05x+ and 3.3v dips into 3.295 at worst)... When I check them in the BIOS they look the same 'cept for the 12v which is usually above 12v... It strikes me as kinda odd. The system is stable at it's current speed (Prime stable, Prime + looped MP3 + rthdribl at that). The only other components not listed in the sig are two optical drives (DVD-ROM and a 16x NEC DVD-RW) and a SB Audigy. Does PC Probe just report 12v lower than it is? Is it actually that low once I enter Windows (hard to believe considering the stable OC but I wouldn't know)?

The only other note-worthy fact is that it locks up at 2.4GHz no matter what I try (only thing I've left to try is 1.4-1.45 vcore, tried 1.65v even and it was slightly better but locked up within a couple hours). Not sure if it may be actually be a 12v line problem and the PSU is at fault (see sig).
 
Oh and... Anyone know if MBM (or some other prog., recommendations are welcomed) will read the A8V voltages correctly? It'd probably be worth it to see what another program displays even if it's stable I guess, at 'least I'd know the line would be one of the possible causes for the wall I've hit in OC'ing.

My vcore swings from 1.504 to 1.520 at times during load btw. Not sure if that's very relevant.
 
Why couldnt your 12V line actually be running at 11.5V? Have you had a multimeter across it to check? 11.5V is still within spec for an ATX supply.
 
Dunno, I thought people tend to say it shouldn't go lower than 11.8/11.9? Maybe I'm wrong, I don't own a multimeter though... Nice to know it's still technically within spec though, thanks.
 
Spec for the 12V line is 11.4V to 12.6V, so +- 5%. So you shouldnt have issues, although you dont seem to be pullong a helluva lot of current on 12V, unless you have a lot of optical drives/ccfls etc, not in your sig.
 
Impulse said:
The only other components not listed in the sig are two optical drives (DVD-ROM and a 16x NEC DVD-RW) and a SB Audigy.
Oh and an internal USB (header) CF/SD card reader, doub that draws much current at all. Both the case fans are connected to one line to the PSU that's not driving anything else.

The opticals are on another line, the SATA HDD is on it's own, and the BFG is on the same line as a PATA drive atm (that's not actually hooked up to an IDE port yet, it's an old drive I wanna transfer some stuff off from, haven't had a chance to).

Rest of the stuff inside is all in my sig, RAM is at stock vdimm. No case lighting as of yet (other than the LED on the front and PSU fans).
 
Its prob nothing to worry about really, as i said, youre still in the right tolerances, so everything in your system will be rated to run at theat anyway. Your motherboard might be at fault as well though, try updating the BIOS, i know mine reports my 3.3V line at 2.7V when its actually 3.4
 
Got the latest BIOS afaik, 1009 (it was posted at the end of Dec. after it went thru a few beta versions). I might grab a multimeter to check the lines sometime, how much would one run me? (hopefully not more than another PSU :p )

Edit: I just remembered I hooked up the HS fan to the mobo when I first set it up and it's been like that ever since... It's a low speed 92mm Panaflo though (L1A), doubt it exceeds the mobo's capabilities.
 
Depends where you are. Mine cost me £3.50, but thats cos i work at maplins, (think radio shack ish but not as shit by the impression i get from peoples comments)
 
Mine was supplying an overvoltage of 14.6V to an Abit AV8 mobo. I guess its better to get less than too much.
 
Back
Top