Asus A8N Wont POST?

Shifra

Gawd
Joined
Feb 13, 2005
Messages
640
Brand new pc, new proc, ram, etc. I have been building PCs for a few years so i think im out of luck however i'd like any ideas.

AMD3500+ 90nm
1gig DDR500 PC4000 Ballistix
X800XT (positive its working)
Antec 480 Neopower

Basically i was going to install a whole new AMD system into a somewhat complex water cooled case. However before i seat everything i simply wanted to make sure it would POST. Nothing ticks me off worse then setting it all up only to find something is bad and having to weave between hoses to yank it out. Plug all the stuff in (CPU has no cooler only a water block without water for the moment), reguardless all i need is for it to POST so, like my LG775 i figure it will boot without coolant for 20seconds. Nothing comes up on screen, it emits 1 long beep then nothing. Obviously i dont dare leave it on for any period of time over 15seconds with the CPU getting no cooling. I'v moved the memory around (yes its installed into B_1 not A_1) and even pulled the CPU as it should still post with an error. I get nothing. At this point im not sure if its the motherboard or a bad memory module. According to Crucials own chart the motherboard does support it so its not a problem of incompatability. It simply emits 1 long beep and wont do anything further.

Suggestions?
 
Remove the ram, see if you get same beep code. Try with one stick of ram in slot B1 see if you get same beep code.

Also plug some speakers in, might get a "post message". *See page 61 of the manual if you do.
 
Hey buddy whats up, im sorry to hear your having problems......i had the A8N-SLI board for a couple of months(just switched to DFI Ultra-D), and i too had problems but i over came them and turned out to be a very decent board indeed. Ill try and help as i have had every problem with thta board to date and i may prove usefull to you. First of all, the most important thing is to get the most updated bios. I know that that MB wont work with a X850 series card untill you update the bios to 1003 or higher, maybe that could be your problem. Another thing is that that board is very sensative to power and memory. Make sure you have the 24 pin power supply or a really high 20 pin power supply(id recomend the 24 pin however). Next, your memory needs to be decent as the board is real picky. OK, i just looked over your specs and i think your problem is the voltage on your CPU, ALOT of people had problems untill they fixed the voltage on there 3500 CPU's. This only applies if you have a 90 core 3500. It has a different power intake(1.4 i think, and the board makes it lower for some reason.) All these solutions wont help unless you can actually post, so what i would do is reset the CMOS. I had a similar problem at first and once i cleared the cmos i got into the bios and went from there. Also, make sure that you 12v line(4-pin) is installed properlly, i know that sounds dumb but it will only beep if your board isnt getting the 12 volts on top of the main power. So, try clearing the cmos first and if that does nothing, post back and we will try something else. I hope it works out for ya, and im here to help as i know how frustrated i was when i first got my board. But i worked it all out.
 
speaking of pluging in power, did you catch the slot near the pci e x 16 slot where you can plug the molex power into , i know that this is only needed for sli, but maybe woth a shot
 
hi ,

i got about the same problem.
when i shutdown from windows my pc goos down ,then when i try to put the computer on
with the power button I get 1 large beep and nothing anymore the pc just halts.
Then i have to shut it down with the powerbutton holding it for 4 seconds.
When it shuts down i push te main button on my powersupply 1 once off and on
push the powerbuttton on my pc and he's ready to go again.
have tryed nummerous combinations cant seem to be able to fiks it????

Another problem i had with my mem i got 1gb of corsair XMS pc4000 ddr500 when i put
my mem on 1T iget also 1 large beep and nothing else.
I have to reset my cmos and put it back on 2t then its ok..
I hate this f**ing mobo never had problems whit soltek ,msi or Aopen or gygabite
I once by an ASUS and this is the last time cost a lot and sucks for support and service!!

bye greets
 
Figured out my prob, as usual its always something small and stupid or major. Just had to remove/replace the SLI connector card. Switched it to dual with my single card and it did the POST fine. The single side is just a really tight fit so it needed more pressure then normal.

q-tip, make sure if you are only using 1 module of ram that its in the third slot over from the processor (slot b_1 in the manual). And make sure you dont have the same problem i did. You should only be able to see the very ends of the metal on the SLI card. This motherbaord also uses the following beep codes:

1 Long, 2 Short Video adapter failure Bad video adapter
Repeating (Endless loop) Memory error Bad memory or bad connection
1 Long, 3 Short Video adapter failure Bad video adapter or memory
High freq. beeps (while running) CPU is overheating CPU fan failure
Repeating High, Low beeps CPU failure Bad processor

a short beep will almost sound like its skipping on a single beep, its very fast.
 
Back
Top