asus a7v333

Farva

Extremely [H]
Joined
Feb 3, 2004
Messages
38,145
what is the fastest cpu i can put into my MB? i want to put in an amd 2800 into it, and the MB says it goes up to 2GHz+.
 
Your best bet is to go to Asus's website and look your board up there. It should say what is the fastest speed CPU you can run on it.

I will tell you right now that you will not be able to run a CPU on there that runs a bus speed higher than 133 (266DDR). The 333 part of the A7V333 just means it will officially support running RAM at 333, not the processor.
 
Asus A7V333 does support 333mhz fsb cpu's as of a certain bios revision. I don't remember which bios, but I know that I ran the latest bios that was available early last year and it supported them.

I was running a xp1800 palomino at 187x9 :cool:

It was a AWESOME motherboard, I wish I didn't accidentally kill it with my screwdriver :(
 
The The VIA KT333 chipset doesn't support 333 FSB Cpus. It only officially supports 333 DDR RAM. Some people can run a higher FSB but the PCI and AGP busses are out of spec and that can cause a problem. Some people get lucky and don't have that problem though.
 
Go here to query A7V333 CPU support. Whether or not KT333 does or doesnt support 333fsb, that motherboard DOES support 333fsb cpu's with bios 1016 and newer.

The PCI/AGP frequency resets at 150mhz to 30mhz and at 166mhz hits back to standard 33mhz. It then goes higher of course. I was able to max out at 187mhz fsb, where the pci was at something like 38 or 39mhz.
 
protias,

Which PCB version is your A7V333?

Version 1.## of that mobo can support only the 266FSB CPUs, up to a 2600+/266 Thoroughbred. Only PCB version 2.00 or higher can support the 333FSB CPUs and the Barton/Thorton core CPUs (with the appropriate BIOS version).
 
Interesting, I was looking at this myself a few weeks ago to give my rig (see sig) a bit more horsepower to tide me over until socket 939. I have a rev 1.01 mobo as well, so I'll have to get a Thoroughbred to replace the Palomino currently in there.

The only thing is, my usual hardware supplier only stocks the 333MHz flavour of the 2600 Thoroughbred. I take it that I will be able to run it at 266FSB so the lack of a bus lock doesn't fry my PCI/AGP stuff?

Also, am I right in assuming these chips will all now be Thoroughbred-Bs? What is the overhead like on them?

[k]

ps - just after I posted, I remembered that my PC Geiger tells me that my FSB is 333MHz, even though my revision of the mobo supposedly only supports 266 CPUs? I'll check I have the settings right, but if it's correct, what's to stop me giving a 2800 Thoroughbred full beans at 333 FSB? I'm guessing there are other changes to the rev 2.x boards for Barton.
 
[k]ar| if you unlock that palomino and raise the FSB/lower the multiplier, you'll get enough horsepower to tide you over :cool:
 
Originally posted by Benny Blanco
[k]ar| if you unlock that palomino and raise the FSB/lower the multiplier, you'll get enough horsepower to tide you over :cool:

OK, I finally got around to checking this out. I have not unlocked my Palomino, but when I go into the BIOS and change the setting to manual, it gives me the following options:

multipliers 13.0 -> 20.0
CPU/PCI frequencies 100/33 -> 227/45
Vcores 1.75 -> 1.85

Is this thing fully unlocked by default from the factory or is my trusty a7v333 pulling some kind of trick to somehow soft-unlock it?

What should I be aiming for in terms of OC? IIRC, my chip is an AGOIA, so I'll cross post later to the OC forum for more tips, but an indication for now would be cool.

Thanks,

[k]
 
Hmm, you might actually be out of luck, because the xp2100 uses the high range of multipliers, and the A7V333 doesn't do what some boards (like the NF7-S) do, which is give the low (12.5 and below) as well as the high (13 and above)....

If you really want to unlock it, I think you'll have to do a bit more than "standard" unlocking to get the low range of multi's.... Check out this page and see if its something you care to get involved in... otherwise, just wait for socket 939 (thats what i'd do if I were you) :D
 
i dont know which version of PCB it is, how do i find this out?
 
Originally posted by protias
i dont know which version of PCB it is, how do i find this out?

The PCB version is located just after the model number (A7V333) on the motherboard itself.
 
Originally posted by E4g1e
The PCB version is located just after the model number (A7V333) on the motherboard itself.

Yep - look between the PCI slots

BTW, thanks for the info Benny. The operation to get lower multipliers looks a bit OTT for me considering the actual benefit of doing it and the fact that I'll probably be moving to 939 in a few months anyway. Mind you, so long as my rig can run upcoming games reasonably I'll be happy. The Far Cry demo seemed OK so I think I'll be fine until 939/PCI-E/BTX.

[k]
 
Back
Top