A7N8X Deluxe problem overclocking

Dominat0r

2[H]4U
2FA
Joined
Jun 28, 2001
Messages
2,646
I just got a Asus board to replace my MSI board.

My last system ran just fine at 200x11 with Stock voltage.

I brought home my new board and got everything up and running. I installed windows without overclocking. I got windows up and running then went into bios and started to raise the FSB. Now when I raise the FSB the computer freezes in the windows start up screen.

The weird part about it is, that if i go back and reset to default FSB, it still freezes in the windows screen. It will sit there for about 5 mins and then reboot itself.

I was also noticing that in my Hardware Monitor in my Bios...it showed my +12V rail at 12.54v Could this be the problem?
 
Forgot to mention...im running my Ram at very loose timings and have tried 2.6-2.8v for it.

Could this be a bad board?

No reason this shouldnt overclock just as good as my MSI board. I cant figure this out to save the life of me.

I bought a new power supply, installing it now.

I also noticed that there is no 4pin AUX power connector on my board. I was just wondering is this just a older revision?
 
Well i guess its a PSU problem. Now i can get to 193x11.5 but cant hit 200 FSB for the life of me...


Any reason why this wouldnt be able to hit that?
 
if the board is rev. 1.xx then its really hard to hit 200fsb, try flashing new bios
if its a rev. 2, could be a psu problem
or try to raise the voltage on the chip
 
Put A multimeter on your rails to make sure you are getting the right readings.
Are you running in dual channel mode (not familier with your MB)Maybe try running in single channel mem?


Not to start a flame fest but MSI makes a decent board!
 
Originally posted by Highlife
Its version 1.04

Running memory in single might yeild better overclock?

no, it wont
most 1.04 boards wont make it past 187fsb, consider yourself lucky
i had a 1.04 board, was able to go all the way up to 200fsb, but it wouldnt even post at 201, and the chip still had alot of headroom (1700+ tbred b)

so, you can either sell the board and get a rev. 2, or youre stuck.
 
Well, what if i put a Barton 3200 in there with the 200 FSB? Seems to me like if it doesnt run that then im stuck.

Anyone thought about RMAing it to Asus? Since it cant run 200FSB CPU then its not what the box says.

Also, im using speedfan and when i opened it for the first time the I have about 12 different temps in there.

3-4 of which are close to the same. Anyone know which is my CPU?
 
Ok this board is driving me crazy...im getting errors in 3dmark2001 like mad....

ARGGG i cant belive this board cant match my overclock of my MSI board.....un real!
 
did you run in single channel mode?

You left the [H] off of ARGGG :D
 
Yea i tried it in Dual and single...

I also tried a 3200 Barton and guess what....wont even boot...even with the jumper set to 200FSB.

Im not overclocked a bit right now and it still getting errors here and there. Reboots and everything...

I dont know what else to do really...very upset with this board. It cant even run a 200FSB CPU no matter what.
 
Time to step away from the dark side and back into the light:eek:

Maybe that board is as finscky as my board was with the ram?
 
Originally Posted by CallMeIshmael
I've seen some posts at AbitUSA'a forum (in the Nforce chipset section) about Nforce2 mobos having problems with overclocking, with 512MB DIMMs in dual channel (something about CPC in BIOS...not a memory geek). If you overclock, you may not see the same FSBs with the 512s you would get with the 256s....
Originally posted by zupadupa
Thanks alot for info on the overclocking of my mobo. Is it true to all revisions of the A7N8X? Any idea what Bios version and board version have that might not overclock well?
Originally posted by CallMeIshmael
Overclocking info only applies with dual channel 2x512MB DIMMs. All Nforce motherboards (except DFI with beta [modded] BIOS), NOT just Asus.
Originally posted by burningrave101 2[H]4U
... I would get 1GB of RAM for sure but you dont really need to worry about enabling dual channel on your Athlon XP board because dual channel benefits the Athlon XP boards very little if at all.
Not sure if the last statement is 100% true.

I guess what I found out is that the Revsion 2.0 boards OC a better then the 1.0x, but not by much. With my 2500+ and revision 2.0 board, I can OC up to a 3200+ with a 200 FSB and probably even higher, but I havent tried to push further since my cooling is mediocre and had little time to try. I guess its luck of the draw, but it really sounds like this board isnt that great for OC'ing (basically from what I have read so far)

Is there any chance on exchaning it for a 2.0 revision??
 
Anyone using Giel Ultra Memory with a Asus board.

I bought a A7N8X-E Deluxe havent had a chance to check it yet, but want to know if anyone is using this two together.

Giel is a pretty good brand of ram, I dunno why it would have problems running on a Asus board....

Anyone let me know....im using PC3500 Giel Ultra Platinum, its got silver heatspreaders on it and its rated at 6-3-3-2.5

I have tried Vcore settings, Vdimm, AGP voltage....everything. Even at STOCK speeds on my 2500 prime95 crashes in about 2 hours.
 
Since you have a revision 1.04 board, you will not have the best chance to get the FSB up to 200. It was something with the early nForce2 chipsets. They didn't usually run 200 FSB and if you got one that did, you were lucky. The chipsets also ran very hot.

I also have a revision 1.04 board but I have one of the good ones. I can run up to 208 FSB stable with my RAM and no extra cooling on the northbrdge, just the passive heatsink.
 
Back
Top