a lil help with over clocking please

Acarey50

n00b
Joined
Mar 25, 2009
Messages
3
ok, first off im a complete newb to over clocking. But with that said and my explanation you shall see its not my knowledge thats the problem i dont think.

first question is : should i be even trying to over clock on my build?

corsair 850w power supply (which im kinda thinking might be the problem)
2600k
asus maximus extreme z68 mobo
16gb of geil memory which was chosen for being the highest ammount of memory that was supported on the manufacturers list of supported memory. also it was a little cheaper and had good reviews.
2X gtx 275's in sli running X16
3X 7200 rpm sata hard drives
1X ocz agility 120 gb ssd sata 6gb
1X 500gb usb hard drive
corsaid H100 for cooling
and three big fans plugged into the board inside a HAF 932 case.

i guess my main question is, is it my PSU thats killing me? everything installed perfect, ran prime for 2 hours, cpu topped at the turbo spec of 3.9. So, feeling confident in my boards ability i figured id give the auto tune a go, and chose the 4.6. it took the clock, booted sucessfully to windows 64bit, then after 30 seconds of prime 95 it BSOD. so i thought maybe it could hack 4.6, so i throttled it back to 4.2, same exact response from the pc. Any ideas? just hoping someone can help before i drop money i dont have on an unnescesary PSU.
 
I doubt very much your PSU is holding you back...I'm not familiar with that board,so someone with that board will be more help, but the first thing is try and do in manually......don't use the auto clock feature....
 
but im curious though, whats the difference between the two? as in whats used when doing it manually thats not in the auto?
 
Auto might not use completely stable settings, it uses generic settings that *most* of the CPUs are stable at.

Besides, overclocking 1155 is so easy, I don't see why you would use the auto overclock feature.
 
Don't use the auto features unless you don't want more than 4.3-4.4 GHz. They often forget little details like the fact that you need to play with PLL Overvoltage if you want to go 4.5 GHz or faster.

Just find a 2600k overclock guide. Don't like the one I linked? Type that into Google and choose one, there are so many!
 
Looking over that parts list the first thing I would single out would be that GeIL RAM. I had 4x 2GB sticks of their DDR2 on my previous build. It would pass memtest all day but BSOD whenever I tried to do anything that loaded up the memory. Took me months to figure out what parts were causing it because individually everything tested fine. I put some Mushkin RAM in instead and never had a problem again.

With my current Asus Maximus IV Extreme-Z I bought the Mushkins to start with and 4.6GHz was easy. I could be entirely wrong but based om my previous experience I know I will never try to save a buck on RAM again.

I also doubt the PSU is the issue.
 
heres another interesting thing i found, i did the over clock thru the bios the next time and it posted again to windows but with the over clock the NIC no longer worked. go back to bios take the over clock off, NIC works fine. Got me.
 
The biggest problem with the auto tune programs, in my opinion, is that they almost always change the BCLK along with the multiplier, which can cause instability. There is no reason, at all, to change the base clock with Sandy Bridge. The extra 2-3% just isn't worth the risk of instability.

Easiest thing to do is go into the BIOS and manually set the turbo multipliers to 42 (or 44) and then boot and see if it is stable. Most SB boards can run overclocks in that range with all Auto settings and only changing the multipliers. Try that first, and see what happens.
 
First, a BSOD is not likely at all to be caused by a poor PSU. Your system turning off might be caused by a poor PSU. So in this case your PSU should be fine. What is more likely to be the problem is the settings for the OC like others have said. Typically with a BSOD you either are not giving enough voltage, or too much voltage. It is best to take it off the auto OC and try a manual OC with the guides.
 
Back
Top