• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Recent content by jamesjohnson88

  1. J

    New Artwork

    I like it but feel it would be improved if the x-shaped plant/grass things did not look the same, or perhaps were not there at all.
  2. J

    640mm external radiator/resevoir project

    There would be a partition between the fans so that they didn't effect eachothers airflow. Yeah, it is 720mm. I was too busy thinking about the different radiator sizes to pay attention.
  3. J

    640mm external radiator/resevoir project

    *bump*
  4. J

    640mm external radiator/resevoir project

    Here is the design I have so far - I haven't measured out yet as I haven't decidedon parts but it'll be roughly as tall as a PC tower, around 15cm wide and 20-30 cm deep. I will probably have mesh cutouts over where the fan partition is to allow air in from the side. I'll most likely...
  5. J

    640mm external radiator/resevoir project

    No, I understand an appreciate the advice. I thought that I may be a problem to start with, ut it would be a lot easier that way, so it was worth asking. Still, I'm keen on the thing to be a tower though, so what do you think about using fans to blow air through the rads, which would both be...
  6. J

    Quad core Intel air cooler......?

    I'm using the Thermalright Ultra-120 eXtreme and its easily the best cooler i've tried. Fairly expensive but easily worth the money.
  7. J

    640mm external radiator/resevoir project

    I did actually mean sandwiched, its would go - In>Rad>Fans>Rad>Out This way the first rad has the air pulled from it and the second has the air pushed through it. Depending on the type of rad (heatercore, etc.) it would dictate which was the primary radiator and therefore whether it was the one...
  8. J

    640mm external radiator/resevoir project

    I just wanted to get a few opinions on a project i'm considering. What I want to do is house 2 360mm radiators in a purpose built box/case. It would be cooled by 3 x 120mm fans sandwiched between them. Obviously they'd be powerful fans so I'd most likely have them on a controller. There...
  9. J

    Splicing a fan controller

    Since spent all my money on a new GPU and Mobo I've had to utilise the fans from my Antec P182 to set-up my cooling in a decent way. I have one colling the HDDs and PSU, one pulling in air from the bottom/front, one exhausting it at the top/rear, and a Noctua 2000 on my heastink blowing the...
  10. J

    Vista Activation

    Well, the mobo should arrive tomorrow, so I guess i'll know for sure then. AT least I hope it arrives tomorrow, it better do for £12 delivery...
  11. J

    Vista Activation

    Ok, so I should be fine then. I doubt i'll be lucky enough for Vista to boot without a re-install, so I guess its time to dig out the linux CD and get the files off my HDD. Somebody mentioned that if you re-installed Vista without a re-format, that it kept your old 'My Docs' files. Can...
  12. J

    Vista Activation

    Hi, i'm hoping I could get some answers here about my vista activation. So here's the story - I built my new rig and installed vista and all the drivers no probs. I didn't activate it, but it said 'auto-activate in 3 days'...anyway, long story short, my mobo died and I am replacing it with a...
See more
Back
Top