ASrock Taichi x370,.. Dr Bug A6

viktum

n00b
Joined
May 2, 2017
Messages
36
Just got my new build done and after POST I am seeing an A6 error on the Dr Bug. I have not installed an OS yet. Thr is 1 HDD and 1 dvdr/w. Does anyon hav any xperience with this error?
So far everything seems to be running fine.
 
Pretty sure
A0 - A7 Problem related to IDE or SATA devices. Please re-install IDE and SATA devices. If the problem still exists, please clear CMOS and try removing all SATA devices.

Which port do you have your drive in? And are both of your drives showing up in Bios?
 
Yes I see both drives in the BIOS. HDD is in port 4 and the dvdr/w is in port 6.
 
If they are both showing up are you having any issues? Seems like it might show that code if there is nothing to boot to, IE no OS
 
No I have not encountered any issues so far. Other than the dr Bug showing A6. No I have not started the OS installation nor have I tried any overclocking. I basically just flashed the BIOS after POST and nothing else.

Should I move forward with clearing the CMOS? I have unplugged both SATA connections.

Also when I reboot with the HDD and dvdr/w disconnected I still see an A6 after reaching the BIOS.
 
Last edited:
The only thing i can think of espically if its the same error code when you have no drives plugged in, basically the board is waiting for the next step which it cant do because there is no boot device.
 
The only thing i can think of espically if its the same error code when you have no drives plugged in, basically the board is waiting for the next step which it cant do because there is no boot device.

Yea that seems logical. I have never built my own PC. So I am a little apprehensive about everything
 
OK the A6 error shows while in BIOS. But is replaced with 24 error after loading into windows.

I am using 8GB x2 GSkill DDR4-3200 PC4-25600. F4-3200C14D-16GFX

One stick is in DIMM A2 and One is in DImm B2
 
OK so I swapped the 2 sticks,. A2>B2 B2>A2

And I reset the cmos. Boot to BIOS still shows A6 error while in BIOS. But, upon BOOT to OS there are no more errors:)

I think I have successfully built my first pc:) WooHoo
 
is the 24 an error or a temp reading?
It was on the Dr. Bug LED

Well I recreated the 24 on the Dr Bug led,....

Seems when I enable the Onboard Debug Port LED, in the BIOs under the advanced tab\South Bridge Config, I am getting the 24 when I boot to OS. This is disabled by default. This option has 3 settings, Disabled, Enabled, and Runetime CPU Temp
 
Last edited:
just something stupid.. I had an error once on an older board with a digital readout on it.. for the life of me, I cannot remember which brand on model.. On most of the mother boards I have seen in the last few years, SATA ports 3-6 are for Sata Express, or M.2 devices.. Some board will disable those ports if an M2 is plugged in.. It might just be a BIOS software issue, where the M2 slot is set to active, but it is detecting drives connected to it.. and giving off the error code.. Nothing is wrong, just freaking it out..
 
Everything seems to be running ok. Boots up flawlessly every time. Ram is running at only 2400 but I have not enable XMP or messed with anything in OC tweaker yet. Just running at stock atm.

Maybee I should just disable the Dr. Bug LED or set it to runtime temp setting?

Really irks me tho. I will always know its there if even if I don't see it. :(
 
Send ASRock an email and ask them about it. Maybe it is something silly like KedsDead said.
 
Well I have finished me build setup. I am not receiving anymore error readings(after entering OS). I am a first time builder and 1st time OC'r. Yet, I was able to get a successful OC. I cannot get the RAM to 3200+mhz. Due to my lack of experience and the touchy relationship between RAM and these type of boards, I settled on 2933 No OC on RAM and XMP enabled at stock timings. I got the r5 1600 to 3800. I did bump the SOC voltage to 1.1 but I am not sure I really needed too.
Not much of an overclock.I know this setup can do better.
I got close with RAM at 3200+(stock 3200 with XMP would not boot-gskill Flare X) I figure I might try again later on a new BIOS update.(currently 2.30)

Completed MEMtest86 successfully.
Completed a 20min LinX burn.
Completed 3DMark Time Spy Benchmark and their 10min Stress test.
Completed CPUz benchmark and outscored r7 1700 on single thread and r5 1600x on multi thread.


I will probably do more long term stress testing over the next few nights.
Thanks for all comments.
 
Last edited:
Well I have finished me build setup. I am not receiving anymore error readings(after entering OS). I am a first time builder and 1st time OC'r. Yet, I was able to get a successful OC. I cannot get the RAM to 3200+mhz. Due to my lack of experience and the touchy relationship between RAM and these type of boards, I settled on 2933 No OC on RAM and XMP enabled at stock timings. I got the r5 1600 to 3800. I did bump the SOC voltage to 1.1 but I am not sure I really needed too.
Not much of an overclock.I know this setup can do better.
I got close with RAM at 3200+(stock 3200 with XMP would not boot-gskill Flare X) I figure I might try again later on a new BIOS update.(currently 2.30)

Completed MEMtest86 successfully.
Completed a 20min LinX burn.
Completed 3DMark Time Spy Benchmark and their 10min Stress test.
Completed CPUz benchmark and outscored r7 1700 on single thread and r5 1600x on multi thread.


I will probably do more long term stress testing over the next few nights.
Thanks for all comments.

Yeah you should not worry about things like ram at this point in time , take another look a few bios revisions later.
Are you using stupid amount of voltage for ram ?
 
Yeah you should not worry about things like ram at this point in time , take another look a few bios revisions later.
Are you using stupid amount of voltage for ram ?
No I took all voltages back to auto and just have cpu at 3800 and RAM is xmp enabled at 2933 with stock timings and auto voltages. I am content with it for now. I will try later on. There is already ya new BIOS out. But I will wait for a few more months. This setup will handle everything I need atm.
 
Yeah the newer agesa code for 1.0.0.6 came out for the asrock boards. I would give that a try. Not sure you should need it i heard great things about the Taichi and flarex. I can also tell you i have the asrock killer ac board and i loaded up the newer bios and it didnt help me get past 2933 either.
 
Yeah the newer agesa code for 1.0.0.6 came out for the asrock boards. I would give that a try. Not sure you should need it i heard great things about the Taichi and flarex. I can also tell you i have the asrock killer ac board and i loaded up the newer bios and it didnt help me get past 2933 either.
Ah ic. It just feels like it should work when I start tweaking settings to get the 3200. I am sure someone with more experience in this could get it working. I will probably try it on the 2.4 update or the next one. Hopefully one of these BIOS updates will make it work with just xmp and stock/auto settings for noObs like me.
 
Ah ic. It just feels like it should work when I start tweaking settings to get the 3200. I am sure someone with more experience in this could get it working. I will probably try it on the 2.4 update or the next one. Hopefully one of these BIOS updates will make it work with just xmp and stock/auto settings for noObs like me.

And you are right in that regard that if you can not get it to work without jumping through 200 different hoops and still don't have a stable result or a result which matches someone with nearly the same hardware why not wait until they do have a bios which is better or more flexible with the ram you have.
 
And you are right in that regard that if you can not get it to work without jumping through 200 different hoops and still don't have a stable result or a result which matches someone with nearly the same hardware why not wait until they do have a bios which is better or more flexible with the ram you have.

Did you entertain the possibility that his chips IMC might be a little weaker than on other Ryzens' ?
 
Did you entertain the possibility that his chips IMC might be a little weaker than on other Ryzens' ?
Supposedly 3200 should be less of a problem.


https://rog.asus.com/forum/showthre...EFI-build-1401&p=655766&viewfull=1#post655766

3600 may never be possible for all people on this platform, even if you have an Intel-rated 4266 kit. Too many variables. 3200 is the doable zone for most CPUs/kits/boards. After that, things become more conditional.
 
Here is a review from the 3200mhz flarex kit + your taichi on newegg.

Pros: - Works well with my Ryzen 1700/asrock taichi MB
- Good speed and latency

Cons: - None so far

Other Thoughts: Initially would only boot to 2933 XMP with my particular MB with older bios, just flashed to the AGESA 1006 bios and now runs at advertised speed. As ryzen matures and firmware improves these issues should resolve. After browsing the forums, there seems to be no sure fire combination that works despite the manufacturer QVLs, but these sticks seem to be among the best for ryzen compatibility. Make sure your bios is up to date no matter who makes your MB. Going to see how high I can OC these eventually, hoping to hit upper 3000's
 
Here is a review from the 3200mhz flarex kit + your taichi on newegg.

Pros: - Works well with my Ryzen 1700/asrock taichi MB
- Good speed and latency

Cons: - None so far

Other Thoughts: Initially would only boot to 2933 XMP with my particular MB with older bios, just flashed to the AGESA 1006 bios and now runs at advertised speed. As ryzen matures and firmware improves these issues should resolve. After browsing the forums, there seems to be no sure fire combination that works despite the manufacturer QVLs, but these sticks seem to be among the best for ryzen compatibility. Make sure your bios is up to date no matter who makes your MB. Going to see how high I can OC these eventually, hoping to hit upper 3000's
If you get to 3600mhz it will be because you have a superior IMC on your chip, but it is UNLIKEY. Getting 3333mhz is doable. I could NOT boot to 3466 with my FlareX DDR4 3200.
 
Back
Top