Slim or other type CPU coolers

carlmart

Gawd
Joined
Sep 17, 2006
Messages
691
This is a problem I also had with my past mobo, which now died: CPU cooler advancing over memory slots.

I imagine it must be a common problem on small form mobos, particularly those with just two mem slots. How are you people solving it?

At the same time I need it to fulfill its cooling function well and be as silent as possible. So to start with it must have a 120mm fan.

Which one would you recommend?
 
I forgot to mention it: mine is an i7 3770 LGA1155 cpu. But I am not overclocking or anything like it.

The cooler I was using was a Corsair A50.
 
It may be useful to know which motherboard in particular you are using. Due to the necessary proximity of the memory slots to the CPU socket (for architectural/electrical reasons), it will probably be very difficult to find a 120mm air cooler that does not extend over the memory slots. An AIO with a 120mm radiator may be your best option. Most AIO pumps do not extend beyond the immediate CPU socket region and with a 120mm fan should run reasonably quiet, though pump noise may become an issue.
 
You mean a liquid cooler? Out of the question.

Absurdly expensive over here and I don't think they are comfortable to use.

Now I had an idea: what happens if I invert the Corsair cooler positioning and make it blow inside the case? Will that heat up the memory heatsinks?

I might try to revert the cooler fan, so it blows outside, supposedly sucking the hot air from the heatsink, but I'm not sure how effective that might be.

The mobo I'm talking about is the Asus H61M-A.

I was looking at some horizontal coolers, but I'm not sure if they really will cool the cpu or how noisy they might be.
 
Assuming adequate airflow and the lack of overclocking, the stock CPU cooler can probably handle the load well enough.

I have had good experiences with mounting the fan on the back of a Hyper 212+/EVO so that the memory can still be easily accessible. That Corsair appears similar. Testing it should be easy enough. Thermal reporting for Ivy Bridge CPUs tends to be reasonably accurate in my experience.
 
Unfortunately I haven't got the stock CPU cooler anymore, if it actually came with it. But you can find it around.

You're right: the Hyper 212 is similar to the Corsair. Did you mount the fan blowing into the back, towards where the memory is or inverting the flow?

I am worried that testing with the cpu and increasing the heat might harm it .
 
OTOS, blowing the fan towards the back would also send some air into the mobo chipset, that uses to get quite hot.

The distance between the heatsink and the memory is 1", so I think there wouldn't be any hot air to affect the memories. What I'm not sure is about the whole air-flow inside the case, which would now be closed, as there would be two fans up front blowing air into the HDDs.
 
This is a problem I also had with my past mobo, which now died: CPU cooler advancing over memory slots.

I imagine it must be a common problem on small form mobos, particularly those with just two mem slots. How are you people solving it?

At the same time I need it to fulfill its cooling function well and be as silent as possible. So to start with it must have a 120mm fan.

Which one would you recommend?

If this is a major concern, Crucial sells a VLP (Very Low Profile) kit of their DDR3 1600mhz ram. It is shorter than the actual DIMM retention clips.

Comparison shots:

Sport VLP

Sport VLP 2

Note there is also a "Tactical LP" which is the same module, but has a small heatspreader. It is still smaller than a standard DIMM.

Tactical LP

--

Further comparison shots
 
I have some Ballistix Sport DDR3 that isn't VLP and is slightly taller, but is still much shorter than some Mushkin DDR3 I have which I will say is "standard height" as in most sticks I've seen are about the same height. The Crucial does clear my Xigmatek heatsink while the Mushkin would only clear if I bent some (4 or so) of the bottom fins up on the heatsink.

It's been very good to me, but one thing I have not done is overclock the RAM. With RAM I tend to stick to rated speeds and undervolt as much as possible rather than overclock. But since OP is talking about clearing heatsinks, I can definitely recommend the Ballistix Sport, and the VLP seems even better.
 
As an Amazon Associate, HardForum may earn from qualifying purchases.
I don't need one, but now I want one :(

Yeah, I haven't bought one yet, but the moment I need a new cooler it's top of my list.

My Mugen 2 is still doing just fine on my overclocked 2500k. This one is supposed to be better and easier to install, and or course smaller. Yay, progress!
 
The message I had written didn't get through.

Problem solved. The inverted cooler worked out fine and things are great.

Now I need a SATA adapter that I have to plug on the PCIEX1 that is below the graphic card fan. How do I do to get there?

This arrangement will have to do until I get a real mobo, probably a Z97, next time I travel abroad.
 
Yeah, I haven't bought one yet, but the moment I need a new cooler it's top of my list.

My Mugen 2 is still doing just fine on my overclocked 2500k. This one is supposed to be better and easier to install, and or course smaller. Yay, progress!

I had a Mugen 2 and yeah, the install was a major pain. It was like doing surgery. I got it done OK but if I hadn't found a youtube video I'd probably still be working on it. Thanks for the tip on the other cooler, I'll keep that in mind the next time I build.
 
Back
Top